Eliminator Lighting LED CLOUD Bedienungsanleitung

LED CloudLED Cloud

User Manual

SKU#: LED CLOUD

UPC#: 817175010198

instructions herein are subject to change without notice. Eliminator logo and identifying product

names and numbers herein are trademarks of Eliminator Lighting. Copyright protection claimed in-

cludes all forms and matters of copyrightable materials and information now allowed by statutory or

judicial law or hereinafter granted. Product names used in this document may be trademarks or reg-

istered trademarks of their respective companies and are hereby acknowledged. All non-Eliminator

brands and product names are trademarks or registered trademarks of their respective companies.

Eliminator Lighting and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/

or as a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and

operation of this product.

Eliminator Lighting USA

6122 S. Eastern Ave. | Los Angeles, CA 90040 USA

Tel: (323) 948-0480 | Fax: 888-287-5224 | www.eliminatorlighting.com | [email protected]

GENERAL INFORMATION

INTRODUCTION

Please read and understand all instructions in this manual carefully and thoroughly before attempting

to operate this product. These instructions contain important safety and use information.

UNPACKING: This product has been thoroughly tested and has been shipped in perfect condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If the car-

ton appears to have been damaged, carefully inspect your product for damage and be sure all ac-

cessories necessary to assemble the product have arrived intact. In the event that damage has been

found or parts are missing, please contact our customer support team for further instructions. Please

do not return this product to your dealer without rst contacting customer support at the number

listed below. Please do not discard the shipping carton in the trash. Please recycle whenever pos-

sible.

CUSTOMER SUPPORT

Tel: (323) 213-4592 | Fax: (323) 582-2941

www.eliminatorlighting.com | [email protected]

WARRANTY RETURNS

All returned service items, whether under warranty or not, must be freight pre-paid and accompa-

nied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside

of the return package. A brief description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping container. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. Items returned without an R.A. number

clearly marked on the outside of the package will be refused and returned at customer’s expense.

You may obtain an R.A. number by contacting customer support.

Eliminator Lighting warranty is valid from the date of purchase. Our 1 year limited warranty cov-

ers manufacturing defects only. Serial number and place of purchase with dated valid receipt must

be submitted at time of service. Eliminator Lighting warranty does not cover items or parts prone

to wear and tear: lamps, LEDs, fuses, brushes, and belts. Eliminator Lighting warranty is only valid

within the United States of America.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt to perform any repairs

yourself, as doing so will void your manufacturer’s warranty. In the unlikely event that your unit may

require service, please contact Eliminator Lighting. Eliminator Lighting will not accept any liability for

any resulting damages caused by the non-observance of information in this manual or any unauthor-

ized modications to this unit.

During operation, the housing may become extremely hot. Avoid touching the unit with bare hands

while in use.

LIMITED WARRANTY (USA ONLY)

A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the original purchaser, ADJ Products, LLC

products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of

purchase (see specic warranty period listed below). This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s responsibility to estab-

lish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product,

please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Prod-

ucts, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts re-

placement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a des-

ignated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No

accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products,

LLC shall have no liability whatsoever for loss of or damage to any such accessories, or for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modied in any manner

which ADJ Products, LLC concludes, after inspection, aects the reliability of the product; if the product has been

repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was

issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth

in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up.

During the period specied above, ADJ Products, LLC will replace defective parts at its expense with new or refur-

bished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or

workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the

product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered

by this warranty were manufactured after August 15, 2012, and bear identifying marks to that eect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products with-

out any obligation to include these changes in any products theretofore manufactured. No warranty, whether

expressed or implied, is given or made with respect to any accessory supplied with products described above.

Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection

with this product, including warranties of merchantability or tness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or t-

ness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be

such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC

be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to Eliminator Lighting, an ADJ Products, LLC brand, and su-

persedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

All Eliminator Lighting products (except laser diodes) = 1-year (365 days) Limited Warranty (Such as: Special

Eect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans,

Trussing, Lighting Stands etc., excluding lamps)

Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited war-

ranty)

Batteries = 180 Day Limited Warranty

To register your Eliminator Lighting product online, please click here to the ADJ Warranty Registration Page:

https://www.adj.com/portal/user/register/

SAFETY GUIDELINES

THERE ARE NO USER SERVICEABLE PARTS INSIDE THESE DEVICES. DO NOT

ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFAC-

TURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THESE

DEVICES AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDE-

LINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE

NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.

NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

ALWAYS REPLACE FUSES WITH REPLACEMENTS OF THE SAME TYPE!

KEEP FLAMMABLE MATERIALS AWAY FROM THESE DEVICES!

INDOOR / DRY LOCATIONS USE ONLY!

DO NOT EXPOSE DEVICES TO RAIN AND/OR MOISTURE!

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY CLEANING OR

MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an extend-

ed life. The frequency of cleaning depends on the environment in which the device operates: damp,

smoky, or particularly dirty environments can cause greater accumulation of dirt on the xture hous-

ing and/or light xture optics. Clean the external surface and the front lens of the device periodically

with a soft cloth to avoid dirt/debris accumulation

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no

user serviceable parts inside these devices; please refer all other service issues to Eliminator Light-

ing. Should you need any spare parts, please order genuine parts from Eliminator Lighting.

FUSE REPLACEMENT

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder

located inside the power socket. Insert a at-head screw driver into the power socket and gently pry

out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in

socket for a spare fuse; be sure not to confuse the spare fuse with active fuse.

INSTALLATION INSTRUCTIONS

FLAMMABLE MATERIAL WARNING

Keep devices at least 5.0 feet (1.5m) away from ammable materials and/or pyrotech-

nics.

ELECTRICAL CONNECTIONS

A qualied electrician should be used for all electrical connections and/or installations.

DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!

OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING CALCULATING

WORKING LOAD LIMITS, KNOWLEDGE OF INSTALLATION MATERIAL BEING USED, AND

PERIODIC SAFETY INSPECTION OF ALL INSTALLATION MATERIALS. IF YOU LACK THESE

QUALIFICATIONS, DO NOT ATTEMPT THE INSTALLATION YOURSELF. IMPROPER INSTALLA-

TION CAN RESULT IN BODILY INJURY.

BEFORE RIGGING/MOUNTING DEVICES TO ANY METAL TRUSS/STRUCTURE OR CEILING, A

PROFESSIONAL EQUIPMENT INSTALLER MUST BE CONSULTED TO DETERMINE WHETHER

THE METAL TRUSS/STRUCTURE OR CEILING IS PROPERLY CERTIFIED TO SAFELY HOLD

THE COMBINED WEIGHT OF THE LIGHT FIXTURE, CLAMPS, CABLES, AND ACCESSORIES.

BEFORE MOUNTING DEVICES TO ANY SURFACE OR STRUCTURE, MAKE SURE THE SUR-

FACE OR STRUCTURE CAN HOLD A MINIMUM POINT LOAD OF 10 TIMES THE WEIGHT OF

THE DEVICES.

MAKE SURE SCREWS AND/OR ANCHOR BOLTS (NOT INCLUDED) FIT INTO MOUNTING

HOLES!

FOR ADDED PROTECTION, MOUNT DEVICES OUTSIDE WALKING PATHS, SEATING AREAS,

OR AREAS WHERE UNAUTHORIZED PERSONNEL CAN REACH THE DEVICES.

SECURE FIXTURE WITH A SECONDARY SAFETY ATTACHMENT, SUCH AS AN APPROPRIATE-

LY RATED SAFETY CABLE. (NOT INCLUDED)

NEVER STAND DIRECTLY BELOW THE DEVICES WHEN MOUNTING, REMOVING OR SERVIC-

ING.

DEVICES MUST ALL BE INSTALLED FOLLOWING ALL LOCAL, NATIONAL, AND COUNTRY

COMMERICAL ELECTRICAL AND CONSTRUCTION CODES AND REGULATIONS.

OPERATING INSTRUCTIONS:

This unit is a 4 channel DMX intelligent LED unit. It can be run as a stand-alone or in a primary-sec-

ondary conguration. The unit has 3 operating modes: sound active mode, auto mode, and DMX

controlled. This unit has been inspected at the factory for problems and defects. No assembly is

required, and the unit is ready to be plugged in to a power outlet. A fog machine can be used in con-

junction with this device to enhance the display. The instructions below explain the operation of each

mode in detail.

Auto Run Mode:

1. Plug the xture in and press the MODE button until “AU.XX” is displayed. “XX” represents the cur-

rently selected running speed.

2. Press ENTER, then use the UP and DOWN buttons to adjust the running speed. The running

speed can be adjusted from “AU.00” (slowest speed) to “AU.99” (fastest speed).

Sound Active Mode: In this mode the LED Cloud will react to sound.

1. Plug the xture in and press the MODE button until “SU.XX” is displayed. “XX” represents the cur-

rently selected sound senstivity level.

2. Press ENTER, then use the UP and DOWN buttons to adjust the sound sensitivity. The sensitivity

can be adjusted from “SU.01” (least sensitive) to “SU.99” (most sensitive).

DMX Mode: Operating through a DMX controller gives the user the freedom to create their own pro-

grams tailored to their own individual needs. The LED Cloud has 4 DMX channels. See the chart in

the DMX Traits section of this manual for the DMX traits and values.

1. This function will allow you to control each individual xture’s traits with a standard DMX 512 con-

troller.

2. To run your xture in DMX mode, press the MODE button until “AXXX” is displayed. “XXX” repre-

sents the currently selected DMX address. Press ENTER and use the UP or DOWN buttons to nd

your desired DMX address.

3. After you have chosen your desired DMX address, plug in the xture via the XLR connections to

any standard DMX controller.

Primary-Secondary Conguration:

1. Daisy chain your units together via the XLR connectors on the rear of the units. Use standard XLR

data cables to link your units together. Remember that the Male XLR connector is the input and

the Female XLR connector is the output. The rst unit in the chain (primary) will use the female

XLR connector only, and the last unit in the chain will use the male XLR connector only.

2. Connect the rst “Secondary” unit to the “Primary.”

3. Set the “Primary” unit to your desired mode of operation. On the “Secondary” unit, set the DMX

address to “001”. The “Secondary” unit will now follow the “Primary”.

SYSTEM MENU

DMX TRAITS

Eliminator LED Cloud - DMX Traits

CHANNEL DMX VALUE DESCRIPTION

Color Macros

000 - 007 Blackout

008 - 015 Red

016 - 023 Green

024 - 031 Blue

032 - 039 White

040 - 047 Amber

048 - 055 Red + Green

056 - 063 Green + Blue

064 - 071 Blue + White

072 - 079 White + Amber

080 - 087 Red + Amber

088 - 095 Green + Amber

096 - 103 Blue + Amber

104 - 111 Red + Blue

112 - 119 Red + White

120 - 127 Green + White

128 - 135 Red + Green + Blue

136 - 143 Green + Blue + White

144 - 151 Blue + White + Amber

152 - 159 Red + White + Amber

160 - 167 Green + White + Amber

168 - 175 Red + Green + Amber

176 - 183 Red + Green + White

184 - 191 Red + Blue + Amber

192 - 199 Red + Blue + White

200 - 207 Green + Amber + Blue

208 - 215 Red + Green + Blue + White

216 - 223 Green + Blue + White + Amber

224 - 231 Red + Green + Blue + Amber

CONTINUED ON NEXT PAGE

DMX TRAITS

Eliminator LED Cloud - DMX Traits

CHANNEL DMX VALUE DESCRIPTION

Color Macros (continued)

232 - 239 Red + Green + White + Amber

240 - 247 Red + Green + Blue + White + Amber

248 - 255 Sound Active

Rotation

000 - 009 Stop Rotation

010 - 120 Clockwise Rotation, fast to slow

121 - 134 Stop Rotation

135 - 245 Counter-Clockwise Rotation, fast to slow

246 - 255 Stop Rotation

Strobe

000 Strobe O

001 - 255 Strobe Speed, slow to fast

4000 - 255 Dimmer, 0% to 100%

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eliminator Lighting DJ-Equipment Handbücher

Eliminator Lighting

Eliminator Lighting Katana LED Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Stealth Wash Zoom Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting EM20 Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting TriDisc9 LED Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 146 CYCLOPS Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Electro 64 BLED Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Furious Five RG Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Mini Par UV LED Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting EM12 Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 143 ASTEROID Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting EZ8 System Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting UV Disc Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting LED Moon Beam Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting FROST FX BAR RGBW Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting MEGA PAR PROFILE EP Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting EM30 Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting COSMIC BURST Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Follow Spot 100 LED Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Electro Swarm Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 141 OCTO BAR Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Moon Beam Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting Mini Par RGBW LED Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung