Eling 8OZ Bedienungsanleitung

8OZ POPCORN MACHINE

INSTRUCTION MANUAL

ALWAYS READ ALL INSTRUCTIONS BEFORE USING

IMPORTANT SAFEGUARDS

Safety precautions should always be followed when using electrical

appliances. These precautions include the following:

1. READ ALL INSTRUCTIONS PRIOR TO USING YOUR POPCORN MACHINE.

2. Before operating the popcorn machine, always make sure it is located on a flat and level surface.

Do not place the unit on or near a hot gas or electric burner or in a heated oven.

3. KEEP OUT OF REACH OF CHILDREN. Close supervision is necessary when it is being used

near children.

4. Position appliance close to a power outlet to avoid the possibility of tripping over the power cord.

5. Always connect the electrical cord between the popping kettle and the main unit first, and then

connect the main power cord into a wall outlet.

6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of

electrical shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not

fit into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not

attempt to modify the plug in any way.

7. The popping kettle should NOT be connected to ANY electrical cord not included in this unit.

8. Do not leave power cord hanging over the edge of a table or counter and do not allow it to come in

contact with any hot surfaces.

9. Do not operate the appliance with a damaged cord or plug, with a malfunction, or with any

mechanical damages.

10. NEVER LEAVE UNATTENDED WHILE IN USE.

11. Do not touch hot surfaces. Always use handles or knobs to operate.

12. Keep door closed while operating. Do not touch kettle while operating – this area gets HOT.

Kettle surface is HOT and should NOT be touched during popping or immediately after use.

13. Do not pop kernels with a dry popping kettle (i.e., without oil). To avoid overheating, always add oil

first and then kernels before operating.

14. Be very cautious when emptying popcorn from the popping kettle to avoid burns from the kettle or

from residual oil.

15. Allow HOT parts to cool down before moving. Use extreme caution when moving the appliance

containing hot oil or other hot liquids.

16. Turn ALL switches to “OFF” position before disconnecting power plug from the wall supply outlet.

17. Unplug main power cord from outlet while not in use and before cleaning the popcorn machine.

18. To avoid any risk of electrical shock, do not immerse cord or plug into water or other liquid.

19. Do not immerse popping kettle set into water. NO PARTS ARE INTENDED FOR THE

DISHWASHER.

20. DO NOT USE ANY ABRASIVE CLEANING MATERIALS.

21. The use of any accessory or attachment not provided or recommended by manufacturer may

cause injury. NEVER FORCE ANY PARTS OR BRACKETS INTO POSITION.

22. Unplug, clean and store the popcorn machine in a dry and safe place if not being used for a long

time.

23. Not recommended for use outdoors.

24. Do not use appliance for other than indicated usage.

SAVE THESE INSTRUCTIONS

-1-

INSTRUCTIONS

Thank you for purchasing the vintage style popcorn machine, which uses the latest

technological advances in kettle popcorn operation.

Model No. & Specifications: Model No.:81200 & 81201

Voltage: AC 120V~60Hz

Input Power: 850W

Please read this Instruction Manual carefully before assembling and using the popcorn

machine.

PARTS

FOR TABLETOP MODELS ONLY:

A. Main unit x 1 pc B. Kettle x 1 pc

C. Popcorn scoop x 1 pc D. Kernel scoop + Oil scoop set

Assemble the kettle (B) on the supporters

which are built into the main unit (A), and

connect the socket.

-2-

FOR TABLETOP WITH CART MODELS ONLY:

A. Main unit x 1 pc B. Kettle x 1 pc

C. Working platform x 1 pc D. Hand rail x 1 pc

E. Square pole x 2 pcs F. Long stand x 1 set

G. Short stand x 1 set H. Wheel axle x 1 pc.

J. Wheels x 2 pcs. K. Storage cabinet x 1 pc

L. Popcorn scoop x 1 pc M. Kernel scoop + Oil scoop set

N. Cart hardware box include:

(Package A) 9/16”X1/2” Bolts x 8 pcs. + Nuts x 8 pcs. + Washers x 8 pcs.

(Package B) 9/16”X1-3/8” Bolts x 8 pcs. + Washers x 4 pcs.,

(Package C) 9/16” Nuts with round cap x 2 pcs. + Washers x 2 pcs.

(Package D) Wrench x 2 pcs

Assemble the kettle (B) on the supporters

which are built into the main unit (A), and

connect the socket.

-3-

CART MODELS (81210 & 81211) ASSEMBLING PROCEDURES:

1. Use bolts & washers (Package B) provided to connect the Long stand (F) and the 2 pcs

square pole (E) together.

2. Connect the completed above (1) with the short stand (G) by the bolts & washers

(Package B).

3. Insert axle (H) into short stand. Place

sleeves and washers (Package C) onto

each side of wheels (J) and then fix it with

round cap nuts by wrenches provided

(Package D).

4. Turn the storage cabinet (K) up side

down for convenient assembling. Insert

both ends of the short and long stand

into the bottom of (H) and then fix by

bolts in (Package B).

5. Turn the complete unit back to up-right

position. Install the handrail (D) on the

storage cabinet (K) [on the other side of

the wheels (J)] & the working platform

same side of the wheels (J)] by bolts &

nuts with washers included in (Package

A).

6. Place the main unit (A) onto the topside

of the storage cabinet. Use the four spring

loaded latches (Under the Main Unit) to

secure the popping unit to the storage

cabinet.

7. Hook up the Kettle (B) onto the hanger.

(Caution: Roller bar should be on the door

side and also check if gears between pot and ceiling are perfectly matched).

8. Connect the power plug from the ceiling with the socket on the bottom of the kettle.

-4-

USING YOUR POPCORN MACHINE

1) Make sure the popcorn maker is unplugged before you do any of the following.

2) Before using the unit, please check carefully if voltage is suitable to the country. (Please

check if the voltage is matching with rating label specified next to the power cord).

3) Clean the internal surface of the kettle and main unit surfaces.

4) Main unit has 3 function switches as follows:

Spot light and warmer (I)

Stirrer (II)

Stainless steel Kettle heater (III)

5) Hook up the kettle onto the hanger of the main unit.

6) Plug in the power cord to the popcorn maker.

7) Switch on the light and heater (I & III), and then fill in suitable amount of butter or oil

(Fig. 1). Consumer could fill amount of oil (Max. 15g) subject to your own

preference .

8) Kettle should be pre-heated for 3 to 4 minutes with oil (until steam comes out from

the kettle). Please prepare kernels with sugar. (Measure amount of kernels by

measuring scoop provided and amount of sugar subject to your own preference, liquid

sugar and honey are prohibited to be used.)

9) Open the lid and then pour in pre-mixed kernel and sugar. (Fig. 2)

Caution: Lid might be hot and recommend using an oven mitten.

10) Switch ON the Stirrer (II) so that it starts stirring. (Fig. 3)

11) Close the door carefully.

12) Popcorn starts popping out through the lid after about 2 to minutes. (Fig. 4)

13) Switch OFF the stirrer & heater (II & III) when popping completed

(No more popping

sound from kettle). Rotate the roller bar of the kettle and

pour out all remaining

popcorn from kettle.

-5-

14) Keep heater switch (III) OFF if the unit is not continuously running. Keep only the

spot light and warmer ON to keep the popcorn warm, dry and tasty.

15) Serve your popcorn with popcorn scoop provided.

16) Remove plug from power supply if the unit is not being used for a long time.

17) Repeat steps 7 to 10 for continue popping.

Fig. 2 Fig. 3

Cleaning and Maintenance

-With a clean damp cloth, wipe the doors, glass and metal surfaces. Do NOT use any

acidic, citrus based cleaners or abrasive cleaners on the acrylic doors as they might cause

scratching or dullness.

-Frequently empty the catch tray of unpopped popcorn kernels and clean with soap and

water. Dry thoroughly.

Frequent cleaning of the popcorn kettle is strongly recommended. This will help prevent

burning of excess oils on the bottom of the kettle.

-Let the unit cool down before cleaning.

-Use wet cloth to clean the kettle surface inside and out.

To thoroughly clean the popcorn kettle, turn off the unit and add 1-1/2 to 2 cups of hot water

into the kettle (no detergent is necessary). Place a towel in the bottom of the main unit and

place a large bowl or container on the towel (the container must be large enough to

easily pour water from the popcorn kettle). Turn ON the Stirrer & Heater (2) and bring water

to boil for 1 to 2 minutes. Turn OFF stirrer and heater and carefully pour the water from the

popcorn kettle to the bowl or container. CAUTION: Kettle and water will be HOT! Repeat

same procedure 2 to 3 times for best results.

Never immerse the kettle into water or place in dishwasher.

-6-

Fig. 1

Fig. 4

Inhaltsverzeichnis

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

Vogue

Vogue D446 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

ADE

ADE AUTOMATIC-L Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung