Elitegroup Computer Systems K7S5A+ Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 6

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 25

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 47

Preface i

Features and Packing List Translations 錯誤! 尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction.................................................................................................1

Checklist.....................................................................................................1

Standard Items................................................................................................. 1

Features .....................................................................................................2

Choosing a Computer Case .......................................................................3

Mainboard Components .............................................................................4

CHAPTER 2 6

Installing the Mainboard 6

Safety Precautions......................................................................................6

Quick Guide................................................................................................6

Installing the Mainboard in a Case..............................................................7

Checking Jumper Settings..........................................................................7

Setting Jumpers ............................................................................................... 7

Checking Jumper Settings............................................................................... 8

Jumper Settings ............................................................................................... 8

Connecting Case Components.................................................................10

Front Panel Connector................................................................................... 12

Installing Hardware...................................................................................13

Installing the Processor.................................................................................. 13

Installing Memory Modules .......................................................................... 15

Installing a Hard Disk Drive/CD-ROM......................................................... 16

Installing a Floppy Diskette Drive................................................................. 18

Installing Add-on Cards................................................................................. 19

Connecting Optional Devices........................................................................ 21

Connecting I/O Devices............................................................................23

External Connector Color Coding................................................................. 24

CHAPTER 3 25

Using BIOS 25

About the Setup Utility..............................................................................25

The Standard Configuration .......................................................................... 25

Entering the Setup Utility.............................................................................. 26

Updating the BIOS........................................................................................ 26

Using BIOS...............................................................................................27

Standard CMOS Features.............................................................................. 28

Advanced BIOS Features .............................................................................. 30

iii

Advanced Chipset Features........................................................................... 32

Integrated Peripherals.................................................................................... 35

Power Management Setup Option................................................................. 39

PNP/PCI Configurations................................................................................ 42

PC Health Status............................................................................................ 43

Frequency/Voltage Control............................................................................ 44

Load Fail-Safe Defaults Option..................................................................... 45

Load Optimized Defaults Option................................................................... 45

Set Supervisor/User Password....................................................................... 45

Save & Exit Setup ......................................................................................... 46

Exit Without Saving ...................................................................................... 46

CHAPTER 4 47

Using the Mainboard Software 47

About the Software CD-ROM ...................................................................47

Auto-installing under Windows 98.............................................................47

Running Setup............................................................................................... 48

Manual Installation....................................................................................50

Utility Software Reference........................................................................50

Introducing the Mainboard

Thank you for choosing the K7S5A+ mainboard. The K7S5A+ is a high per-

formance system board integrated with SiS 745 which supports a 4X AGP slot

for highly graphics display, DDR interface and Ultra DMA 33/66/100 function.

This ATX mainboard which measure 220 mm x 304 mm accommodates AMD

AthlonXP/Athlon/Duron processors supporting frontside bus (FSB) speeds up

to 100/133MHz. It has 3 built-in 184-pin DIMM slots, and the main memory is

expandable to a maximum of 1.0 GB (2 unbuffered DDR333 DIMM) or 1.5GB

(3 unbuffered DDR266/DDR200 DIMM).

To top it all, the mainboard has an extended set of ATX I/O Ports such as dual

channel IDE interfaces, a floppy controller, two high-speed serial port, an

EPP/ECP capable bi-directional parallel port connector, four USB (Universal

Serial Bus) connector, a PS/2 keyboard and mouse connectors. One AGP slot,

five PCI local bus slots and one communication and networking riser (CNR)

slot provide expandability for add-on peripheral cards.

The K7S5A+ has all the features you need to build a powerful multimedia

workstation.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• One auto-install software support CD

• This user’s manual

Processor The K7S5A+ mainboard uses an AMD 462-pin Socket A that

has the following features:

• Supports 200/266 MHz frontside bus (FSB)

• Accommodates AMD AthlonXP/Athlon/Duron processors

Chipset The SiS745 chipset is based on an innovative and scalable

architecture with proven reliability and performance. A few of

the chipset’s advanced features are:

• A low 2.5-volt DDR266 SDRAM power consumption

which makes it an excellent solution for notebooks and

desktops with a small footprint

• Support for a 4xAGP interface providing vivid 3D graphics

and video performance

• An ATA 100 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 100 Hard Disk Drives, delivering maximum

sustained data transfer rates of 100 MB/sec

• Built-in multithreaded I/O link used to enhance perform-

ance, providing enough I/O bandwidth for throughput up

to 1.2 GB/s

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Memory The mainboard can accommodate 2.5V DDR SDRAM. It ac-

commodates three unbuffered 2.5V 184 pin slots. Each slot

can support up to 512 MB with a total maximum capacity of 1.0

GB (2 unbuffered DDR333 DIMM) or 1.5GB (3 unbuffered

DDR266/DDR200 DIMM).

VGA The K7S5A+ includes a 4xAGP slot that provides four times

the bandwidth of the original AGP specification. AGP technol-

ogy provides a direct connection between the graphics sub-

system and the processor so that the graphics do not have to

compete for processor time with other devices on the PCI bus.

AC’ 97 Audio

Codec The AC’ 97 Audio codec is compliant with the AC’ 97 2.2

specification, and supports 18-bit ADC (Analog Digital Con-

verter) and DAC (Digital Analog Converter) resolution as well

as 18-bit stereo full-duplex codec with independent and vari-

able sampling rates.

Onboard LAN

(optional) The Realtek RTL8100B LAN chip is incorporated in the chipset

providing the mainboard with integrated Ethernet PCI LAN

capabilities.

Expansion

Options K7S5A+ has five 32-bit PCI slots, an AGP slot and CNR

(Communications and Networking Riser) slot.

The K7S5A+ supports Ultra DMA bus mastering with transfer

rates of 33/66/100 MB/sec.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• Two serial ports

• One parallel port

• One MIDI/game port

• Two USB ports

• One LAN port (optional)

• Audio jacks for microphone, line-in and line-out

BIOS

Firmware This mainboard uses Award BIOS that enables users to con-

figure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters and memory timing

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 220 x 304 mm. Choose a case that

accommodates this form factor.

Table of Mainboard Components

Label Component

AGP1 Accelerated Graphics Port

ATX1 Power connector

AUDIO Front Audio Connector

BT1 Three volt realtime clock battery

CASEFAN Case Fan header

CD1 Primary CD-in connector

CD2 Secondary CD-in connector

CNR1 Communications Networking Riser slot

CPU1 Socket A for AMD AthlonXP/Athlon/Duron CPUs

CPUFAN Cooling fan for CPU

DDR1~DDR3 Three 184 pin DDR SDRAM

FDD1 Floppy disk drive connector

FIDJP CPU ratio select jumper

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

SIR Infrared cable header

JP1 Clear CMOS jumper

JP2 KB wake-up function header

JP3 BIOS protection jumper

LED1 Memory module LED

PANEL Connector for case front panel switches and LED

indicators

PCI1 ~ PCI5 Five 32-bit add-on card slots

PWRFAN Power Fan connector

SJ Single LED header

SPKR1 Speaker connector

USB2/USB3 Front panel USB headers

WOL1 Wake On LAN wakeup connector

WOM1 Wake On Modem wakeup connector

Note: LED1 is usually connected to a light that indicates that the computer is

powered on. Do not install hardware or disconnect power cables while the

LED is on.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

• Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

• Leave components in the static-proof bags they came in.

• Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 4

Installing the Mainboard in a Case Go to page 7

Setting Jumpers Go to page 7

Installing Case Components Go to page 10

Installing the CPU Go to page 13

Installing Memory Go to page 15

Installing an HDD and CD-ROM Drive Go to page 16

Installing an FDD Go to page 18

Installing Add-on Cards Go to page 19

Connecting Options Go to page 21

Connecting Peripheral (I/O) Devices Go to page 23

Inhaltsverzeichnis

Andere Elitegroup Computer Systems Hauptplatine Handbücher

Elitegroup Computer Systems

Elitegroup Computer Systems 741-M Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P5TX-AR Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P4ITM Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems AF1 Deluxe Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P6IWM Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems 748-A Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P6EX-A+ Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems Z170-LIGHTSABER Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P6VPA2T Einrichtungshandbuch

Elitegroup Computer Systems

Elitegroup Computer Systems K7AMA3 Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems P6VXM2T Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems K7S5A2 Bedienungsanleitung

Elitegroup Computer Systems

Elitegroup Computer Systems K7AMA2 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung