EliteProAV Pro Frame Thin Series Bedienungsanleitung

V03182021-JA www.eliteproav.com 1

Pro Frame Thin Series

EDGE FREE® Matte White Fixed Frame Screen

USER’S GUIDE –E Type

_____________________________________________________________________

Product Description:

The Pro Frame Thin Series is a fixed frame projection screen that uses Elite ProAV’s EDGE FREE®

technology. The EDGE FREE®design resembles a giant size flat panel TV display. The Pro Frame Thin

includes a micro-thin aluminum bezel trim to further enhance the frame appearance. An LED kit is also

included for mood lighting.

The screen material included is our CineWhite®,which is a matte white tensioned front projection material for

environments with controlled lighting.

For optimum projection qualities and performance, please refer to the list below for proper maintenance and

cleaning.

•Use a dry microfiber cloth to remove dust from the screen’s surface.

•When cleaning, use a damp microfiber cloth with warm water to remove any marks.

•Never rub or apply pressure when cleaning the surface.

•Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.

•In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any

other sharp or abrasive objects.

1. Frame and Edge TrimParts List

Qty

item

2 pcs

Main Frame Parts

Qty

item

2 pcs

Edge Trim Parts

Part

vertical frame

Part

½ horizontal frame

Part

½ horizontal frame

Part

V03182021-JA www.eliteproav.com 2

Frame Assembly

Step 1: Place the soft padded foam sheet on a clean area on the ground where the screen will be assembled.

Step 2:Position the pieces of the frame on the foam sheet in the arrangement shown below.

2. Hardware Parts List

Item

Parts List

PFT

100H

PFT

110H

PFT

120H

PFT

135H

PFT

150H

Center Joints (1)

Elbow Joints (2)

M4x6 Screws

Spring Hook

Spring

104

116

128

Top wall brackets

M5x50 Wall Screws

Hollow Wall anchors

Bottom wall brackets

Angle cover

LED light strip clip

Center Support Bar

White gloves

Fiberglass rods

Foam Sheet

V03182021-JA www.eliteproav.com 3

Step 3: Remove the foam on all frame ends before assembling the frame.

Step 4: Insert the center joint (a) connectors into one-half of the horizontal frame (b/c) and secure with the

M4x6 screws (c).

Step 5: Connect the elbow joints (b) to the top and bottom sections of the vertical frame. Once inserted,

connect the vertical sections of the horizontal frame sections. Make sure all holes are in alignment and the

frame pieces are flush (no gaps). They should form perfect right angles.

Step 6: Secure the elbow joints by fastening them with M4x6 screws (c), 4 at each corner.

2. Hardware Parts List

V03182021-JA www.eliteproav.com 4

Screen Material

Step 7: Put on the white gloves(m) and carefully unroll the screen material on a clean surface from the roller

to the other side as shown below. The back side of the screen material should be placed upwards.

Step 8: Insert the fiberglass rods (n) through the openings. The longer rods are used on the vertical edges of

the screen material, and the shorter rods are used on the horizontal edges, as shown below.

Step 9:Carefully and gently place the assembled frame on top of the screen material. Make sure to not allow

the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

Step 10: With one end of the spring and secure inside the groove of the frame, use the spring hook (d) to

attach the spring to the hole located on the screen material’s outer edge in the following order.

Attach the four corners first (1). After those are secure, connect the vertical portions of the material, begin in

the center and move towards the corners (2). Lastly, connect the horizontal sections of the material by

connecting the center of the material and make your way towards the corners (3).

Back side

Back Side

RFront

V03182021-JA www.eliteproav.com 5

Note (after all springs have been attached):

Correct material installation –Corners of the screen material are properly wrapped around the corner edges

of the frame and material is evenly tensioned and flat, creating a nicely taut surface.

Incorrect material installation –Thecorners of the screen material are not properly wrapped along the edge

of the frame leaving the material with unbalanced tension and an uneven finish. To correct, detach springs

from material at the corner(s) where material does not lie flat along the edge of the frame, reposition the

material so that it lies flat and wraps along the edge of the frame, and reattach springs to the material.

Center Support Bar

Step 11: Insert the Center Support Bar (i)into the upper top groove on the back of the frame with the bottom

end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are

in alignment with the groove.

Diagonal Models 150” and below use 1 x Center Support Bar

To avoid ripples forming in the material it is imperative that all of the corners are properly wrappedaround the

edges as illustrated in the check mark diagrams.

V03182021-JA www.eliteproav.com 6

How to avoid getting ripples on the screen material’s projection surface.

Solution: Pull and smooth out the material using your hand from the center to the corners, creating a

nicely taut surface as shown below.

Attention: Do not proceed with the Edge Trim installation until making sure there are no ripples

in the material.

Edge Trim Installation

Step 12: Place the Edge Trim over each end of the frame and secure with M4x6screws (c).

Start with the center points first, then the rest of the corners as shown below.

Step 13: Installthe angle cover(j)on each corner of the frame and install the LED light strip to hold down the

angle cover.

Then insert the LED light clip (l)to hold the LED light strip in place.

V03182021-JA www.eliteproav.com 7

Wall Installation

Step 14:Measure the overall length and height of the frame and drill holes for the top brackets. Line up the

wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver.

If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws

with a screwdriver. Make sure the brackets are leveled.

Step 15: Position the fixed frame screen onto the top wall brackets as shown below and push down at the

center of the top of the frame to secure.

Step 16: With the frame slightly tilted outward; connect the bottom brackets onto the bottom groove of the

frame. Then secure them by screwing onto the wall.

For Technical Support or an Elite ProAV contact in your area, visit

www.eliteproav.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EliteProAV Projektionsfläche Handbücher

EliteProAV

EliteProAV EDGE FREE Aeon ALR Series Bedienungsanleitung

EliteProAV

EliteProAV Tab-Tension Pro Series Bedienungsanleitung

EliteProAV

EliteProAV T153UWS1-D Bedienungsanleitung

EliteProAV

EliteProAV Presenter Pro DarkUST 2 Series Bedienungsanleitung

EliteProAV

EliteProAV CLR Series Bedienungsanleitung

EliteProAV

EliteProAV Pro Frame Acoustic Series Bedienungsanleitung

EliteProAV

EliteProAV EDGE FREE Pro Frame Thin UST Series Bedienungsanleitung

EliteProAV

EliteProAV Yard Master Pro 2 Series Bedienungsanleitung

EliteProAV

EliteProAV Kestrel Stage Series Kurzanleitung

EliteProAV

EliteProAV WhiteBoardScreen TE Series Bedienungsanleitung

EliteProAV

EliteProAV Planate Tab-Tension Series Bedienungsanleitung

EliteProAV

EliteProAV Manual Grande 2 Series Bedienungsanleitung

EliteProAV

EliteProAV AV Manual B Series Gebrauchsanweisung

EliteProAV

EliteProAV Planate Tab-Tension Series Bedienungsanleitung

EliteProAV

EliteProAV TensionPro TP200 XHW2 Bedienungsanleitung

EliteProAV

EliteProAV Pro Frame Series Bedienungsanleitung

EliteProAV

EliteProAV CineGrey 5D Bedienungsanleitung

EliteProAV

EliteProAV ITE139XW2-E8 Bedienungsanleitung

EliteProAV

EliteProAV Saker Series Bedienungsanleitung

EliteProAV

EliteProAV Presenter Pro CLR 2 Bedienungsanleitung

EliteProAV

EliteProAV Saker Tab-Tension CineGrey 5D Series Bedienungsanleitung

EliteProAV

EliteProAV Spectrum2 Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung