Elkay 4400BFEVGWR Installationshandbuch

Page 1 1000004001 (Rev. A - 08/2017)

4400BF_FTN_AWR, LK4400BF_FTN_AWR

Endura II™ Steel Outdoor Pedestal Fountain with Bottle Filling Station with rounded corner design, heavy-duty steel with textured powder-coat

nish and E-Coat immersion for year-round beauty with minimum maintenance. The E-Coat immersion process coats the inside and outside for

the ultimate in corrosion protection.

• Ambient Air Temperature: 50-100.4 °F (10-38 °C).

• Water Pressure: 20-100 psig (0.14-0.69 MPa).

• Maximum Water Temperature: 90 °F (32 °C).

• For Outdoor Commercial Use only.

• Water Inlet: 3/8” (9.5mm) O.D. unplated copper tube.

• Waste Water Outlet: 1-1/4” (38.1mm) O.D. tube.

DANGER – Indicates death or serious injury will result if proper precautions are not taken.

WARNING – Indicates death, serious injury or property damage can result if proper precautions are not taken.

CAUTION – Indicates some injury or property damage may result if proper precautions are not taken.

Denitions

Authorized Service Personnel – Factory trained personnel or personnel having working knowledge of electrical,

plumbing, and machine (appliance) maintenance procedures.

Safety

DANGER

• Please read these instructions completely before starting the installation or performing any service. Failure to follow the instructions and safety

precautions in this manual can result in serious injury or death.

• After installation, keep these instructions in a safe location for future reference.

• Electric supply must be identical in voltage, cycle, and phase to that specied on nameplate.

• Electrical supply must have Ground Fault Circuit Interrupter (GFCI) protection.

• A means for disconnecting electrical supply to the unit must be incorporated in the xed wiring in accordance with wiring rules. This is to allow

electrical disconnection of the unit from electrical supply after installation.

WARNING

• For use with clean, clear potable drinking water only. Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before the system.

• Installation and connection to water and electrical mains must be in compliance with local and national laws.

• All Installation and Service work must be performed by an authorized service personnel.

CAUTION

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities

or lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children

without supervision.

• To prevent a metallic taste or increased metal content in the water due to an electrolysis process caused by electrical feedback from the

grounding of electrical equipment to water supply and water waste mains, connect to these mains using non-conductive materials. The provided

solenoid valve regulator assembly meets this requirement.

Description

Ratings

Installation / Care / Use Manual

Original Instructions

Models: 4400BFEVGWR & LK4400BFEVGWR

Page 21000004001 (Rev. A - 08/2017)

4400BF_FTN_AWR, LK4400BF_FTN_AWR

Installation

For correct and safe installation, please read these instructions completely.

• All Installation work must be performed by an authorized service personnel.

• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.

• Unit not suitable for installations where water jets could be used.

DANGER

WARNING

• Shut off water supply serving the Installation area to reduce risk of water damage.

• Ensure proper ventilation by maintaining clearance from cabinet louvers to wall on each side of Cooler as specied in installation instructions.

• Never wire compressor directly to electrical supply.

• Thoroughly ush all water lines and ttings of all foreign matter before connecting to Cooler.

• Warranty is void if Installation is not made in accordance with current Manufacturing instructions.

CAUTION

• Hose-sets are not to be used for connecting to water mains.

• If inlet pressure is above 100 psig (0.69 MPa), a pressure regulator must be installed in water supply line. Any damage caused by reason of

connecting this product to water supply line pressure outside it’s rated pressure, is not covered by warranty.

• Tools/Items required but not provided:

Installation

Operation: Start-Up

1. Turn water supply on and inspect for leaks. Fix all leaks before continuing.

2. Connect plug end of International Power Cord Set (sold separately) into electrical outlet and turn on power supply to remote chiller.

Note: The inital dispenses might have air in line which may cause a sputter. This will be eliminated once all air is purged from the line. A steady

stream of water assures all air is removed.

3. Recheck all water and drain connections with water owing through system.

• Water Shut-off Valve with 3/8” (9.5mm) compression outlet.

• Waste Trap (non-metallic)

• Safety Glasses

• Protective Gloves

• 5/16” (8mm) Hex Socket or Flathead Screwdriver

• 3/32” (2.4mm) Hex Key

• Fasteners for wall type

1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure.

NOTE: Mounting structure must be capable of supporting 300 lb. load on fountain.

2. Refer to rough-in for plumbing.

3. Install shut-off valve on water supply. (Valve not furnished)

4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished).

5. Prior to installing the Bottle Filler to the fountain, insert drain tube (Item # 4) by positioning the short end of drain pipe through the mounting

plate of bottle ller. Install ller onto fountain and secure with mounting hardware.

6. Connect water supply and fountain drain. Water connection and drain must comply with local codes.

7. Turn on water supply and check all connections for leaks.

CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the inlet water supply

exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line pressures lower than 20 PSI or higher than 105 PSI is not

covered by warranty.

8. Water supply 3/8” O.D. unplated copper tube. Waste 1-1/4” IPS. Contractor to supply waste trap and service stop valve in accordance with

local code.

9. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being connected to fountain.

This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color, or sediment problems.

10. Connect fountain to supply line with a shut-off valve and install a 3/8” unplated copper water line between the valve and the cooler. Remove

any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive stop, approximately 3/4” (See Fig. 2). DO

NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

1/4” O.D. TUBE

WATER INLET

TO COOLER

3/8” O.D. TUBE CONNECT

COLD WATER SUPPLY

BUILDING WATER

INLET

NOTE: WATERFLOW

DIRECTION

SERVICE STOP

(NOT FURNISHED)

Figure 1 Figure 2

Page 3 1000004001 (Rev. A - 08/2017)

4400BF_FTN_AWR, LK4400BF_FTN_AWR

O1/2"

13mm (6)

O14"

356mm

O12"

305mm B.C.

203mm

30"

762mm

64"

1626mm

44"

1118mm

149/16"

371mm

10"

254mm

76mm

29 1/2"

750mm

LEGEND

A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT

SHUT OFF VALVE BY OTHERS

B = ACCESS PANEL ( 8" X 10" )

Figure 3 (Rough-In)

Service

• Safety Glasses

• Protective gloves

• 5/16” (8mm) Hex Socket or Flathead Screwdriver

• 3/32” (2.4mm) Hex Key

For proper and safe servicing, please read these instructions completely.

DANGER

• All Service and Maintenance must be performed by an authorized service personnel.

• Shut off water supply serving the unit before any service work to reduce risk of water damage.

CAUTION

• Tools/Items required but not provided, for Servicing:

Page 41000004001 (Rev. A - 08/2017)

4400BF_FTN_AWR, LK4400BF_FTN_AWR

Service: Inspection/Cleaning

• Inspect Cooler twice each year for proper operation and performance.

• Inspection of the unit will require removal of panels, etc. and reassembly and return to service practices.

1. Cleaning: Warm, soapy water or mild household cleaning products can be used to clean the exterior panels. Extra caution should be used to

clean the mirror nished stainless steel panels. They can be easily scratched and should only be cleaned with mild soap and water or Windex

glass cleaner and a clean, soft cloth. Use of harsh chemicals or petroleum based or abrasive cleaners will void the warranty.

2. Water Flow: Conrm proper water ow. If water ow is slow, inspect lter or inline strainer for restriction. Replace lter cartridge if required.

Disassemble inline strainer and clean if required.

3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize o-ring water seal. To remove tubing from

the tting, relieve water pressure, push in on the gray collar before pulling on the tubing. To insert tubing, push tube straight into tting until it

reaches a positive stop, approximately 3/4” (19mm). See Figure 2.

PARTS LIST

ITEM NO. PART NO. DESCRIPTION

128955C Cover - Round Plate

245931C Outdoor Bottle Filler Drain Plug

345832C Access Panel

466815C Tube - Drain

575724C Screw - 1/4”x20 x 3/4” LG. Pinned Torx

698685C Kit - Hardware/Bolts/Nuts/Wshrs/Torx Screws

71000004179 Kit - (BF) Waterway/Nipple/Gasket/Tubes/Ftgs

81000004180 Kit - Regulator Assy. Wras (BF Only)

91000004181 Kit - Nozzle/Aerator/Gasket/Pin/Key

10 98680C Kit - Aerator/Key

98681C

1000003692

1000003693

Kit - Blank Bottle Filler Trim

Kit - LK4400BF Bottle Filler Trim

Kit - 4400BF Bottle Filler Trim

98682C

1000003694

1000003695

Kit - Push Button w/Blank Nameplate

Kit - Push Button w/LK4400BF Nameplate

Kit - Push Button w/4400BF Nameplate

13 98683C Kit - Drain Adapter/Gasket/Nut/Washer

14 97247C Kit - VR Torx Screws/Bit

NS 1000004069 In-Line Strainer

PRINTED IN U.S.A.

Halsey Taylor – halseytaylor.com

Elkay – elkay.com

6, 14

Figure 5

5, 6

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816

2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

6, 14

5, 6

Figure 6

NS = Not Shown

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay 4405BFFR Bedienungsanleitung

Elkay

Elkay 4420FR FTN A Series Bedienungsanleitung

Elkay

Elkay Soft Sides Series Installationshandbuch

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay EDFP220RC Installationshandbuch

Elkay

Elkay LVRCTL8 1D Series Installationshandbuch

Elkay

Elkay LZOOTL8WSS2KN Bedienungsanleitung

Elkay

Elkay SWIRLFLO LRPBD2 8WSC Series Gebrauchsanweisung

Elkay

Elkay EDFP19C*A Installationshandbuch

Elkay

Elkay Swirlflo Freeze Resistant Fountain... Gebrauchsanweisung

Elkay

Elkay Soft Sides FLEXI-GUARD ERO28C C Series Installationshandbuch

Elkay

Elkay EFRP8C Installationshandbuch

Elkay

Elkay LK4400 Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD EFHA8 1M Series Installationshandbuch

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay LK4410BFFR FTN A Series Bedienungsanleitung

Elkay

Elkay 4405BFFR Bedienungsanleitung

Elkay

Elkay 4410BF Bedienungsanleitung

Elkay

Elkay Soft Sides ERFPD28C Installationshandbuch

Elkay

Elkay 4410FR-FTN Bedienungsanleitung

Elkay

Elkay EDFAC11PBC Installationshandbuch

Elkay

Elkay EWCDA B Series Installationshandbuch

Elkay

Elkay OFA25 2FJO Series Installationshandbuch

Elkay

Elkay ERFP8C*B Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung