Elkay EFA8 2YJO Series Installationshandbuch

PAGE 1

EFA8_2KJO

1000003124 (Rev. A - 12/15)

Installation / Care / Use Manual

Original Instructions

Models: EFA8*2YJO, EFA8*F2YJO, EFA8*P2YJO, EFA8*FP2YJO

Description

Refrigerated Drinking Fountain (Cooler) delivers chilled, clean potable drinking water. Water Cooler houses the refrigeration and delivers a

steady stream of water for direct drinking at the press of the pushbutton.

Ratings

• Electrical: 230Vac, 50Hz, (See nameplate for Amperage), 1 phase.

• Ambient Air Temperature: 50-100.4 °F (10-38 °C).

• Water Pressure: 20-100 psig (0.14-0.69 MPa).

• Maximum Water Temperature: 90 °F (32 °C).

• Refrigerant: HFC-R134a

• Ingress Protection: IP21

• For Indoor Commercial Use only.

• Water Inlet: 3/8”O.D. unplated copper tube.

• Waste Water Outlet: 1-1/4” O.D. tube

DANGER – Indicates death or serious injury will result if proper precautions are not taken.

WARNING – Indicates death, serious injury or property damage can result if proper precautions are not taken.

CAUTION – Indicates some injury or property damage may result if proper precautions are not taken.

Denitions

Authorized Service Personnel – Factory trained personnel or personnel having working knowledge of electrical, plumbing and

machine (appliance) maintenance procedures.

Safety

DANGER

• Please read these instructions completely before starting the installation or performing any service. Failure to follow the instructions and

safety precautions in this manual can result in serious injury or death.

• After installation, keep these instructions in a safe location for future reference.

• Electric supply must be identical in voltage, cycle, and phase to that specied on nameplate.

• Electrical supply must have Ground Fault Circuit Interrupter (GFCI) protection.

• A means for disconnecting electrical supply to the unit must be incorporated in the xed wiring in accordance with wiring rules. This is to

allow electrical disconnection of the unit from electrical supply after installation.

WARNING

• For use with clean, clear potable drinking water only. Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before the system.

• Installation and connection to water and electrical mains must be in compliance with local and national laws.

• All Installation and Service work must be performed by an authorized service personnel.

CAUTION

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or

lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children

without supervision.

• To prevent a metallic taste or increased metal content in the water due to an electrolysis process caused by electrical feedback from the

grounding of electrical equipment to water supply and water waste mains, connect to these mains using non-conductive materials. The

provided non-metallic In-line Strainer meets this requirement.

PAGE 2

EFA8_2KJO

1000003124 (Rev. A - 12/15)

Installation

For correct and safe installation, please read these instructions completely.

• All Installation work must be performed by an authorized service personnel.

• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.

• Unit not suitable for installations where water jets could be used.

DANGER

WARNING

• Shut off water supply serving the Installation area to reduce risk of water damage.

• Ensure proper ventilation by maintaining clearance from cabinet louvers to wall on each side of Cooler as specied in Rough-In.

• Never wire compressor directly to electrical supply.

• Do not solder tubes inserted into the In-line Strainer as damage to the o-rings may result.

• Thoroughly ush all water lines and ttings of all foreign matter before connecting to Cooler.

• Warranty is void if the plumbing kit or glass ller is not specied for use by the Manufacturer for this particular model.

• Warranty is void if Installation is not made in accordance with current Manufacturing instructions.

CAUTION

• Hose-sets are not to be used for connecting to water mains.

• If inlet pressure is above 100 psig (0.69 MPa), a pressure regulator must be installed in water supply line. Any damage caused by

reason of connecting this product to water supply line pressure outside its rated pressure, is not covered by warranty.

• This cooler is manufactured in such a manner that it does not in any way cause taste, odor, color, or sediment problems. If a taste,

odor or sediment problem is prevalent, try installing our water lter on the supply line.

• Tools/Items required but not provided.

o Water Shut-off Valve with 3/8” (9.5mm) compression outlet.

o 1-1/4" (31.8mm) Waste Trap (non-metallic)

o Safety Glasses

o Protective Gloves

o 5/16" (7.9mm) Hex Driver or Flathead Screwdriver

o C-13 Modular International Power Cord Set

Installation: Cooler Mounting

1. Select installation location. Installation location must be a at surface. Installation location should ensure proper ventilation by maintaining 4"

(102mm) minimum clearance from cabinet louvers to wall.

2. Remove front panel by unscrewing (2) 5/16" (7.9mm) Hex Head screws. Set panel aside.

3. Installation area must also include water supply, electrical supply and suitable drain. Water, drain and electrical supply systems must comply

with local code requirements.

Installation: Water Line connection

1. Ensure Mains Water Supply has Water Shut-off Valve with 3/8” (9.5mm) compression outlet.

2. Connect loose end of supplied 3/8” (9.5mm) unplated copper tube to Water Shut-off Valve. See Figure 1.

• NOTE: If 3/8” (9.5mm) copper tube must be cut for proper t, remove all burrs from the outside of tube and re-ush before use.

3. Install waste trap. Remove the slip nut and gasket from the waste trap and install them on the Cooler waste line making sure that the end of the

waste line ts into the waste trap. Assemble the slip nut and gasket to the trap and tighten securely.

4. Turn on building water supply and open Water Shut-off Valve. Check all connections for leaks and correct any found.

Installation: Electrical connection

1. Rotate fan to insure proper clearance and free fan action.

2. Connect modular (C-13) end of International Power Cord Set (sold separately) into Power Inlet on unit and ensure plug-end reaches electrical

outlet. Do not plug into electrical outlet!

NOTE: WATER FLOW

DIRECTION

BUILDING WATER SUPPLY

WATER SHUT-OFF VALVE

(NOT PROVIDED)

1/4" O.D. TUBE

WATER INLET

3/8" (9.5mm) O.D.

UNPLATED COPPER TUBE

IN-LINE

STRAINER

(PROVIDED)

Figure 1

Figure 2

A = White (Neutral)

B = Black (230Vac)

C = Ground (Earth)

D = Fan

E = Freeze Control (when provided)

F = Cold Control (Water)

G = Hot Tank Switch (When Provided)

H = Hot Tank (when provided)

I = Capacitor (when provided)

POWER INLET

PAGE 3

EFA8_2KJO

1000003124 (Rev. A - 12/15)

Rough-In: SCWT14A

Operation: Start-Up

1. Turn on the building water supply and check all connections for leaks.

2. Purge air from all water lines by activating pushbutton with your hand.

3. Recheck all water and drain connections with water owing through system.

4. Rotate fan to ensure proper clearance and free fan action.

5. Connect plug-end of International Power Cord Set (sold separately) into electrical outlet.

6. After verifying that the water cooler is properly connected and operational, replace and reattach cooler front panel by tightening (2) screws.

A = Water Mains Supply, 3/8” (9.5mm) O.D. compression outlet of Shut-off Valve (not provided) to be 1-1/2” (38mm) from Wall

B = Waste Outlet, 1-1/4” (31.8mm) O.D. Drain Tube

C = 1-1/4” (31.8mm) Trap (not provided)

D = Electrical Mains Supply Duplex Outled, 3-wire in Recessed Box. Must have Ground Fault Circuit Interrupter (GFCI) protection

E = Ensure proper ventilation by maintaining 4” (102mm) minimum clearance from cabinet louvers to wall

F = Power Inlet Location

G = Plumbing rough in may be located anywhere within this area

Figure 3

Service

For proper and safe servicing, please read these instructions completely.

• All Service and Maintenance must be performed by an authorized service personnel.

• Disconnect electrical supply to the unit before any service work to reduce risk of electrocution.

• Shut off water supply serving the unit before any service work to reduce risk of water damage.

DANGER

CAUTION

• Tools/Items required but not provided, for Servicing:

o Safety Glasses

o Protective gloves

o 5/16" (7.9mm) Hex Driver or Flathead Screwdriver

Service: Adjustments

1. Temperature Control: Factory set for 50ºF ± 5º (10ºC ± 2.8º) water under normal conditions. To adjust water temperature, remove front panel by

unscrewing (2) 5/16" (7.9mm) Hex Head screws. Set panel aside. Turn screw on cold control (Item 13) clockwise for colder, counter clockwise

for warmer. See Figure 9.

2. Water Stream Height: Stream height is factory set at 35 psig (0.24MPa). If supply varies greatly from this, remove items 1 and 2 and adjust

screw on item 4. Clockwise adjustmentwill raise stream height and counter-clockwise adjustment will lower stream. For best adjustment,

stream should hit basin approximately 6-1/2" (165mm) from bubbler. See Figure 5.

3. Water coming out of Bubbler continuously: When this occurs at the end of the compressor cycle, turn the cold control warmer (Item 13) counter-

clockwise 1/4 of a turn. See Figure 9.

PAGE 4

EFA8_2KJO

1000003124 (Rev. A - 12/15)

Service: Inspection/Cleaning

• Inspect Cooler twice each year for proper operation and performance.

• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc.

and reassembly and return to service practices.

1. Cleaning: Warm, soapy water or mild household cleaning products can be used to clean the exterior panels. Extra caution should be used to clean

the mirror nished stainless steel panels. They can be easily scratched and should only be cleaned with mild soap and water or Windex glass

cleaner and a clean, soft cloth. Use of harsh chemicals or petroleum based or abrasive cleaners will void the warranty.

2. Bubbler: Mineral deposits on the orice can cause water ow to spurt or not regulate. Mineral deposits may be removed from the orice with a

small round le not over 1/8” (3 mm) diameter or small diameter wire.

• CAUTION: DO NOT le or cut orice material. Care must be taken not to damage the orice(s)

3. Condenser Fan Motor: Conrm condenser fan turns freely. If the condenser fan does not spin freely, have an authorized service personnel

replace.

4. Ventilation: Cabinet louvers and condenser ns should be periodically cleaned with a brush, air hose or vacuum cleaner. Cleaning should be done

twice each year or more frequently if needed due to environment. Excess dirt or poor ventilation can cause no cold water and compressor cycling

on the compressor overload protector.

5. Water Flow: Conrm proper water ow. If water ow is slow, inspect lter or inline strainer for restriction. Replace lter cartridge if required.

Disassemble inline strainer and clean if required See Figure 6.

6. Lubrication: Motors are lifetime lubricated.

7. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize o-ring water seal. To remove tubing from the

tting, relieve water pressure, push in on the gray collar before pulling on the tubing. To insert tubing, push tube straight into tting until it reaches

a positive stop, approximately 3/4” (19mm). See Figure 7.

Service: Inspection/Replacement

• Inspect Cooler twice each year for proper operation and performance.

• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc. and reassembly and return to service practices.

1. Bubbler: To remove the bubbler, rst disconnect the electrical supply. Remove the Front Panel by removing (2) screws. To remove the bubbler,

loosen locknut from the underside of the basin and remove the tubing from the quick connect tting (see Figure 7 for actuation of Quick Connect

Fittings). When installing replacement bubbler, tighten nut only to hold parts snug in position. Do Not Overtighten. After servicing, replace the

front panel and two (2) screws.

2. Cleaning Strainer: Restricted water ow may be caused by clogged screen. Remove plug and screen. Clean screen and replace. Lubricate

O-Ring with food grade pharmaceutical mineral oil. Do not overtighten plug or ttings. See Figure 6.

ACBD

A = Plug with 7/8" (22.2mm) Hex

B = O-ring

C = Screen

D = Strainer Body with 1" (25.4mm) Hex

Figure 6

Figure 7

Figure 4

Figure 5

Figure 8

DESCRIPTION

ITEM NO. PART NO.

51299C

98926C

51469C

Filter Assy-1500 Gal.

Kit-Filter Head Fitting Includes

John Guest Fittings

Assy-Filter & Bracket includes Fltr

Head/Mtg Bkt/John Guest Ftgs/

Screws

WATERSENTRY® FILTER PARTS LIST

WATERSENTRY®Filter Detail

PAGE 5

EFA8_2KJO

1000003124 (Rev. A - 12/15)

Cover

Button

Regulator Retaining Nut

Regulator

Hex Nut

Regulator Holder

Basin

Bubbler Assy

Orice Assy

Housing Assy

Pedestal

Bubbler Locknut

Cold Control

Power Cord

Condenser

Fan Shroud

Fan Motor

Fan Blade

Fan Bracket

Fan Blade Nut

Drier

Compressor Service Pack

Kit - Compr Electrical/Relay/Overload/Cover

Receptor Drain

Bracket - Strain Relief

Strainer

Precooler Assy

Heat Exchanger

Evaporator

Nipple-Bubbler (GF)

Gasket (GF)

Poly Tubing (Cut to Length)

Gasket - Drain

Power Inlet

40089C

40048C

15005C

61313C

40169C

50986C

20776C

56073C

40322C

56011C

55997C

75580C

35839C

36024C

66743C

56237C

31430C

30664C

20282C

70018C

66703C

1000002147

98715C

50368C

27962C

55996C

45678C

66576C

66810C

15009C

100322740560

56092C

50005C

35826C

*22

Item

No.

Part No. Description

Replacement Parts: 230V-50Hz Parts List

*Includes Relay & Overload. If under Warranty, replace with same Compressor used

in original assembly.

NOTE: All correspondence pertaining to any of the above water cooler or orders for

repair parts MUST include Model number and Serial number of cooler, name and part

number of replacement part.

Replacement Parts: Color Table

Gray Beige

Almond

Stainless Steel

Sandalwood

Granite

Light Gray

PANEL COLOR

Right Panel (w/ hole) Right Panel (w/o

hole)

Left Panel

COLOR TABLE

20623C

21461C

20625C

21459C

27168C

N/A

27653C

27655C

27652C

27656C

27654C

27657C

20622C

21460C

20624C

21458C

27165C

27166C

For Replacement Parts, contact your local distributor or call 1.800.834.4816

Elkay Manufacturing Co. 2222 Camden Court – Oak Brook, IL 60523 U.S.A – 630.574.8484

Front Panel

20657C

20658C

20654C

21450C

27147C

27148C

Figure 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay Space-ette FLEXI-GUARD FDD Installationshandbuch

Elkay

Elkay EZH2O VRCGN8WS 1C Series Leitfaden

Elkay

Elkay ERO28C*C Installationshandbuch

Elkay

Elkay EDFPVR217RC Installationshandbuch

Elkay

Elkay Slimline EHWM14C A Series Bedienungsanleitung

Elkay

Elkay 4595FR Bedienungsanleitung

Elkay

Elkay HTHBHAC8SSWF25WN Installationshandbuch

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay EDFPW210C Installationshandbuch

Elkay

Elkay 4420BF1UFR Bedienungsanleitung

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD ESRC8,13 1D Series Installationshandbuch

Elkay

Elkay ERPA8C Installationshandbuch

Elkay

Elkay LZOOTL8WSS2KN Bedienungsanleitung

Elkay

Elkay 4400 Series Bedienungsanleitung

Elkay

Elkay Soft Sides FLEXI-GUARD ERO2-8C 2C Installationshandbuch

Elkay

Elkay FLEXI-GUARD EFW16 1E Series Installationshandbuch

Elkay

Elkay Hydroboost HTHBHAC8BLSSWF25N Installationshandbuch

Elkay

Elkay EDFPA17FPC Installationshandbuch

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay 4430FR Bedienungsanleitung

Elkay

Elkay Soft Sides ECDFPW314FPC Installationshandbuch

Elkay

Elkay 4400BFFR Bedienungsanleitung

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung