Elmdene G240 BMU Series Bedienungsanleitung

27.6V

WITCH

ODE

OWER

UPPLY

ODULES

ITH

ATTERY

ONITORING

Models:

G240x MU

Where ‘x’ is max load current: 1A, 2A, 3A or 5A

EATURES

High efficiency cost effective power supply ideal for use in Fire, Access Control and General Security

applications. Featuring a regulated 2 .6Vdc output supplying continuous full rated current to load and up to

an additional 0.5A for charging 2 x 12V standby batteries. Maximum battery life is assured using Deep

Discharge Protection to prevent premature battery failure when operating in standby mode for extended

periods. Two sets of volt-free contacts are provided to signal (i) loss of mains and (ii) battery and loss of

output faults. The universal mains input voltage enables the power supply to be used across a wide

geographical area. The highly efficient switch mode design ensures low operating costs while generating less

heat. The modular construction simplifies maintenance.

•Universal mains input voltage 90-264Vac

•Additional 0.5A to charge 2 x 12V standby batteries

•High efficiency electronics for reduced running costs and lower

operating temperatures

•Continuous full rated current to load

•Volt free contact signalling mains failure

•Volt free contact signalling battery and output faults

•Deep Discharge Protection

•Installer safe design with all high voltage electronics fully shrouded

•Reverse battery connection protection

•Full electronic short circuit and overload protection on load output

•Mains transient protection circuit

•Modular construction for ease of maintenance & installation

•Green Mains present LED

•Orange Battery Charging LED

•Yellow Fault LED

Elmdene International Ltd

Tel: +44 (0)23 9269 6638

3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483

Portsmouth, Hampshire, PO3 5QD, UK 

Web: www.elmdene.co.uk

PECIFICATION

Input Specification

Voltage (rated)

100

240Vac

Voltage (operating)

264Vac

Frequency

60Hz

x Current

See Model Specification T

able

Mains Input Fuse

See Model Specification Table

Max standby Power

0.8W (n

o load

and no battery

connected)

Output Specification

Voltage

2 .0 – 28.0Vdc (2 .6vdc nominal) on mains power

21.0 – 24. Vdc on battery standby

Max load current

See Model Spe

cification Table

Ripple

0 mV pk

pk max

Load output Fuse

See Model Specification Table below

Overload

Electronic shutdown until overload or short circuit removed

(under mains power only)

Local Indicators

MAINS LED

(Green)

FAULT LED

(Yellow)

Charge L

(Orange)

Status

OFF

NORMAL

Battery fully charged

OFF

NORMAL

Battery charging

1s ON, 1s OFF

ON or OFF

FAULT

See signalling outputs

OFF 0.1s ON, 3s OFF OFF

FAULT

Mains Loss; PSU operating under standby

battery

OFF

FAU

No Output, Mains and Battery Loss

Standby atteries

Battery Type

2 x 12V Valve Regulated Lead Acid

Battery Charging Fuse

protection

See Model Specification Table

Battery Re

Charge Time

< 24hr (to 80% of 8Ah capacity)

Signalling Outputs

GEN Fault

(general)

0.1 A @ 60 VDC N/O volt

free contact.

Open when battery disconnected, output fuse fail, battery fuse fail,

output short circuit or low output voltage.

EPS Fault (mains)

0.1 A @ 60 VDC N/O volt

free contact.

Open when loss of mains for more than 8s

Mechanical

Model G2401 MU / G2402 MU G2403 MU / G2405 MU

Module

Dimensions

w x h x d (mm / external) 152 x 106 x 52 15 x 143 x 55

Recommended Batteries 2 x 12V NP or NP1

Weight (excluding batteries)

G2401 MU / G2402 MU G2403NU / G2405NU

280g 650g

Environmental

Temperature -10 to +40°C (operating) 95% RH non-condensing

-20 to +80°C (storage)

Connections

+O/P +ve voltage O/P to load equipment

-O/P -ve voltage O/P to load equipment

+BATT Red lead to standby battery 1

-BATT Black lead to standby battery 2

GEN FAULT Volt-free contacts for general faults

EPS FAULT Volt-free contacts for loss of mains indication

PERATION

This unit is intended for use by Service Personnel only - There are NO USER SERVICEABLE parts inside.

The Green Mains LED will be illuminated whilst the mains supply is present. In the event of a fault condition,

the Yellow Fault LED will be illuminated. The Orange Battery Charging LED will be illuminated when the

battery is not fully charged and is charging normally. When the battery is fully charged it will be

extinguished.

NSTALLATION AND

-U

This unit is only suitable for installation as permanently connected equipment. The PSU is NOT SUITABLE for

external installation. EQUIPMENT MUST BE EARTHED. Before installation, ensure that external disconnect

device is OFF. The PSU should be installed according to all relevant safety regulations applicable to the

application.

Module Enclosure & Mounting

This power supply module has high voltage present and is for use by Service Personnel only. This power

supply module MUST be securely mounted within a robust enclosure having suitable means to prevent

unintentional access to the module. Suitable notices must be affixed to the outside of the enclosure to warn

of high voltages present internally.

Mounting

1) Mount securely in correct orientation allowing minimum clearance of 20mm all round – see diagrams

below.

0m m

20mm

2) The G2401BMU and G2402BMU modules have the option of either being DIN rail mounted (using the

integrated DIN rail mount) or by using appropriate fixings using the four available mounting lugs. The

G2403BMU and G2405BMU modules are fixed using the three available mounting points.

NSTALLATION AND

-U

CONTINUED

Mains Power Up

3) Attach correctly rated mains cable (minimum 0.5mm

[3A], 300/500Vac) and secure in enclosure using

cable ties.

4) Apply mains power. Check for 2 .6Vdc on load outputs. Check Green Mains LED is on.

5) Disconnect mains power.

Load Output

6) Attach correctly rated load cable and secure in enclosure using cable ties. Note polarity.

) Apply mains power. Check green Mains LED is on.

8) NOTE: Yellow Fault LED may flash to indicate no battery has been connected; this is normal.

9) Verify load is operating correctly.

10) Disconnect mains power.

Signalling Outputs

11) Connect EPS and GEN fault outputs to appropriate inputs of control equipment.

Standby attery

12) Connect battery to terminal block using minimum 32/0.2 (1.0mm

CSA) stranded wire.

NOTE: ensure correct polarity of battery connections. Maximum recommended total battery lead

length = 500mm

13) Apply mains power. Check Green Mains LED is ON. Check Orange Charging LED is ON.

14) Check there is no fault indication on Yellow LED.

15) Disconnect mains power. Check that the batteries continue to supply voltage and current to the load.

Check Green Mains LED is OFF and the control panel displays a Loss of Mains (EPS) fault

NOTE: Batteries must have sufficient charge to supply the load

16) Reconnect mains power. Green LED should be on.

1 ) Remove Load fuse. Check Yellow Fault LED is ON and control panel shows General PSU fault.

18) Replace Load fuse. Check Yellow Fault LED is OFF and General PSU fault has cleared at control panel.

0m m

20mm

N E L

G240

1BMU &G2402BMU

G2403BMU & G2405BMU

N E L

L E N

Module Dimensions

128

42,4

152

106

G2401BM & G2402BM

157

128

42,4

G2403BM & G2405BM

Fixing Holes Ø3.3mm

Recommended fixing screw M3

AINTENANCE

There is no regular maintenance required of the PSU other than periodic testing and replacement of the

standby batteries. Reference should be made to the battery manufacturer’s documentation to determine

typical/expected battery life with a view to periodic replacement of the battery.

If the output of the PSU fails the cause of the failure should be investigated e.g. short circuit load. The fault

should be rectified before restoring power to the PSU. The fuses may need to be replaced. Ensure the

correct fuse rating and type is used.

Model Specification Table G2401BMU G2402BMU G2403BMU G2405BMU

Output Current 1A 2A 3A 5A

Max Mains Input Current (at 90Vac) 1.0A 1.3A 1.4A 2.0A

F1 - Mains Input Fuse (20mm HRC) T2.0A T2.0A T3.15A T3.15A

F2 - Output Fuse (20mm) F1.0A F2.0A F3.15A F5.0A

F3 - Battery Fuse (20mm) F1.0A F2.0A F3.15A F5.0A

This p ge h s been intention lly left bl nk

OMPLIANCE

This product meets the essential requirements of the following EU Directives:

Low Voltage: 2014/35/EU

EMC: 2014/30/EU

RoHS2: 2011/65/EU

WEEE: 2012/19/EU

ISPOSAL OF

RODUCT AT

ND OF

IFE

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic Equipment

(WEEE) and 2013/56/EU (Battery). At the end of life, the product must be separated from the domestic

waste stream and disposed via an appropriate approved WEEE disposal route in accordance with all national

and local regulations.

Before disposal of the product, the standby battery must be removed and disposed separately via an

appropriate approved battery disposal route in accordance with all national and local regulations. Package

used batteries safely for onward transport to your supplier, collection point or disposal facility.

See Specification for battery type information. The battery is marked with the crossed out wheelie bin

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For more information see: www.recyclethis.info

Caution: Risk of explosion if b ttery is repl ced by n incorrect type.

Dispose of used b tteries ccording to the b ttery m nuf cturer’s

instructions nd ll loc l nd n tion l regul tions.

The p ck ging supplied with this product m y be recycled.

Ple se dispose of p ck ging ccordingly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elmdene Steuereinheit Handbücher

Elmdene

Elmdene G240xNU Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung