Elmo CRC-1 Bedienungsanleitung
CRC-1
Installation Manual
2
Contents
1. Usage Precautions ..........................................................................................................3
2. List of Contents ...............................................................................................................3
3. Installing the Expansion Board......................................................................................4
Disassembly view ......................................................................................................4
Connecting the connectors and expansion board .....................................................6
Installation method.....................................................................................................7
Cable connections .....................................................................................................8
4. About RS-232C ................................................................................................................9
Supported models .....................................................................................................9
Using the programming tool ....................................................................................10
5. Appendix ........................................................................................................................20
Pin assignment ........................................................................................................20
Command tables......................................................................................................24
RS-232C connector .................................................................................................26
3
1. Usage Precautions
Read "Instruction Manual.pdf" carefully before using this option.
When using an output from the expansion board, do not use an output from the main unit.
Do not use for the objective of output distribution.
2. List of Contents
No. Name Quantity
(1) Programming cable 1
(2) Expansion board 1
4
3. Installing the Expansion Board
Disassembly view
Remove the two screws under the front cover, and remove the rear cover
so that the expansion board can be installed.
Cut out the rectangle perforations on the rear cover so that the
connection cables of the expansion board can be passed through. The
oval perforations are for the fixing screws of the unit.
Caution
To fix the unit with screws, cut out the oval perforated areas.
5
Fix in advance to the installation location.
Connect the expansion board by referring to "Connecting the connectors
and expansion board" on p.6.
After installing the expansion board, reinstall the rear cover (removed in
step (1)).
6
Connecting the connectors and expansion board
The figure below shows the unit with the rear cover removed.
Connect the colored connectors of the expansion board to the unit’s connectors of the
same color.
Details of connectors of the expansion board are described below.
Connector Connector
color
No. of
pins
Connector
name Description
(1) White 2 Power In (DC) Power connector
(2) White 3 AUDIO Output AUDIO output connector
(3) Yellow 2 VIDEO Output VIDEO image output connector
(4) Red 3 RS232C Output RS-232C control connector
(5) Blue 2 IR Output IR control connector
(6) White 9 RGB Output RGB image output connector
Caution
Some connectors are the same shape but different colors. Be sure to connect
connectors of the same color. Otherwise, a malfunction may result.
7
Installation method
The installation method for the expansion board is shown below.
Diameter of installation hole on expansion board: Ф4.7 mm
Use screws that fit this diameter to fix the expansion board to a wall or similar location.
Connect the expansion board to the ground.
8
Cable connections
The methods for connecting peripheral devices to the expansion board are described
below. When connecting the cables, insert them fully and securely into the connectors. If a
connector has fixing screws, tighten them securely.
No. Connector Function Connection
(1) RGB RGB image output Connects to the projector with a VGA cable
(2) VIDEO VIDEO image output Connects to the projector with a video cable
(3) AUDIO Audio output Connects to an external speaker with an
audio cable
(4)*1 RS-232C Control output Connects to the control connector of the
projector with the supplied RS cable
(5)*2 IR Control output Installs the supplied IR cable within the
reception range of the projector
(6) DC IN Power supply Connects the supplied AC Adapter
Caution
*1 If the connector shape on the projector side does not match, create a cable
by referring to "RS-232C connector" on p.26.
*2 Use the bracket or something similar to fix the emitter of the IR cable.
9
4. About RS-232C
Supported models
This section shows the models that are supported by the commands registered in the unit,
and the models that correspond to the model data that is supplied with the programming
tool.
■Supported models (as of February 2010)
1. Initial setting
SANYO：LP-XW200 / LP-XW250 / LP-XW300 / *LP-XW60 / *LP-XW65 / *LP-WXL46
HITACHI：CP-X308J / CP-X417J / CP-X3010J / CP-X2510J
NEC：NP600SJ / NP500WSJ / NP215J / NP210J / NP115J / NP110J
EPSON：EB-410W / EB-826W / EB-825 / EB-85
SHARP：PG-F255W / PG-F312X / PG-F212X
Canon：LV-7375 / LV-7370 / LV-7275 / LV-8300
EIKI：LC-XS25D / LC-XS30D / *LC-XB42D
InFocus：IN2100 / IN2104EP
2. Supplied data
3M：MP8745
BenQ：MP623
MITSUBISHI：LVP-WD510 / *XD250U / *XD280U
Optoma：EX525ST / EX530
Panasonic：PT-LB78V / PT-LB90 / PT-LB90NT / PT-LB75V / PT-LB51NT
For the information registered in the model data, see "Command tables" on p.24.
For the pin assignment of the projector, see "RS-232C connector" on p.26.
Caution
* These projectors use the supplied RS cable's MiniDIN8.
10
Using the programming tool
■Requirements for the Computer on which the programming tool is to be installed
OS: Windows 2000/XP or later
At least one free Com port that operates normally.
■Installation
Obtain a tool that can decompress files with the ".rar" extension. (Example: winrar, winzip)
After decompressing is complete, open the folder.
Select the executable file (Rs 232 Programmer 280510.exe) and change the RS-232C
commands that are registered in the unit.
("280510" of the executable file can be changed occasionally.)
■How to use
When the tool starts, a precaution message is displayed. If you agree with the contents, select
[I AGREE]. This window is only displayed the first time that the tool is started.
Andere Handbücher für CRC-1
1
Inhaltsverzeichnis
Andere Elmo Schalten Handbücher
