ELRO AS80RE11 Bedienungsanleitung

AS80RE11

Wireless Keyfob

Installation Instructions

General Introduction

The Wireless Keyfob is used to Arm, Partial Arm and Disarm the system. The

Keyfob also incorporates a Panic switch that will immediately initiate a Full Alarm

condition when the system is Armed or Disarmed.

Product Overview

A LED indicator

B Arm

C Partial Arm

D Disarm

E Panic Switch

F Key Chain Ring

G Negative Polarity

H Positive Polarity

Binding

Remove the battery cover behind thekeyfob.

Prepare the CR2032 coin cell battery by removing any plastic wrapping onthe

battery. Do not insert the batteries yet into theunit.

Log into the ELRO Smart Home Alarm account from a webbrowser.

Select “System”, then “Add a NewDevice”.

Select “Keyfob”.

The following screen will appear. This means the gateway is entering binding

mode.

Insert the battery ensuring that the +v terminal faces upwards away from the

PCB and replace the battery cover.

The screen below will appear in 10 seconds if the process issuccessful.

Time-out will occur if the binding process was unsuccessful. Please refer to the

“Manual binding” section.

Manual Binding

1. With the battery inserted, repeat steps 3 to 6 of the Binding with Homesys

Within 5 secs, the LED indicator then stop flashing and turn off, indicating the

learning procedure is completed. The screen below will appear indicating the

process is successful.

If after 30 seconds LED flashes rapidly for 3 times, it means the keyfob fails the

binding process

Operation & Testing

Operating the Keyfob

There are 5 operating modes provided by the keyfob.

ARM : Press and release the ARM button.

DISARM : Press and release

PARTIAL ARM 1: Press and release the Partial Arm buttononce

PANIC: Slide the Panic Switch and hold for at least 3 secs beforereleasing.

Note: The LED on the keyfob will turn green after button press is released. This

implies the keyfob receives a confirmation signal from the Gateway. Instead if the

LED turns red, this means the keyfob did not receive the reply from gateway

Testing the Keyfob

section.

2. Press and hold the Disarm button for more than 3 seconds until the LED flashes

Press the Arm button to see if there is an entry in the LOGS page of your

ELRO Smart Home Alarm account.

moderately (on for 2 second; off for 2 second). This implies keyfob has now

entered the binding mode and is waiting to receive binding signals from the

gateway.

Press the Partial Arm button to see if there is an entry in the LOGS page of your

ELRO Smart Home Alarm account.

Press the Disarm button to see if there is an entry in the LOGS page of your

ELRO Smart Home Alarm account.

Slide the Panic Switch and hold for at least 3 secs before releasing. See if there

is an entry in the LOGS page of your ELRO Smart Home Alarm account.

Note: Press the Disarm button to deactivate a triggered alarm and siren sound.

Maintenance

Low Battery: When the battery becomes low, the LED will turn orange after

each press to indicate low battery condition to the user. Replace the battery

when this occurs.

Troubleshooting

The troubleshooting table lists some possible causes and solutions. Please contact

your original retailer or nearest service center if the below solutions cannot solve

your problem.

Specifications

Battery

CR2032 3V/230mAh

Operating Frequency

868MHz

Operating Temperature

-10°C to 40°C

RF Output power

< 25mW

** Specifications are subject to change without notice.

WARNING:

Do not dispose of electrical appliances as unsorted municipal waste, use separate

collection facilities instead. Please contact your local government for information

regarding the collection systems available.

If electrical appliances are disposed of in landfills or dumps, hazardous substances

can leak into the groundwater and get into the food chain, damaging your health

polarity.

out of rangeof and well-being.

When replacing old appliances with new once, the retailer is legally obligated to

take back your old appliance for disposal at least for free of charge.

LED Table

The table below summarizes the LED indication of the keyfob.

Function LED Indication

RF transmission Green LED illuminating for 1 second

Failed RF transmission Red LED illuminating for 1 second

Low battery Orange LED illuminating for 1 second

Binding in process LED flashing with an interval of 2 seconds

Binding successful Green LED illuminating for 0.5 seconds

Binding timeout Green LED flash 3 times.

Reset to Factory Settings

Remove the battery from thekeyfob.

Using two fingers, press and hold both the Arm and Disarm simultaneously

while inserting thebattery.

Keep pressing both buttons for more than 5 secs until the detector’s LED blinks

red, this implies the device is reset back to factorymode.

Note: After power on, the Keyfob will automatically enter “Auto-binding” mode

to bind with a gateway. The auto-binding process lasts for 30 seconds

indicated by the LED blinking slowly.

Symptom

Cause of Failure

Recommendation

LED cannot be

displayed

Run out of battery

power.

Check if reversebattery

Replace a new battery.

Refit the battery with correct

polarity.

LED turns red after

pressing the button

Keyfob is

the gateway.

Move closer to the gateway

Hold the keyfob higher and

press again.

LED blinks green

slowly for 30secs after

power on.

1. Keyfob has not bind

with Gateway

1. Remove the battery and

perform binding

Inhaltsverzeichnis

Andere ELRO Fernbedienung Handbücher

ELRO

ELRO AG40RE11 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung