ELTEX LTP-8X Bedienungsanleitung

Integrated networking soluons

www.eltexalatau.kz/en

Optical line terminals

LTP-8X, LTP-4X

EasyMode manual

Версия ПО3.38.0

LTP EasyMode manual 3.38.0
 2
Содержание
LTP-X EasyMode description ....................................................................................................4
Software and hardware requirements......................................................................................5
Installation and connection.......................................................................................................6
Connection to the terminal........................................................................................................7
1 Console cable connection.........................................................................................................7
2 Connection via Telnet/SSH .....................................................................................................12
Service model in EasyMode ....................................................................................................13
EasyMode enabling and configuration...................................................................................14
1 Default configuration...............................................................................................................14
2 Custom configuration..............................................................................................................15
2.1 VLAN configuration ..........................................................................................................15
2.2 Configuration of the LTP management interface...........................................................15
2.3 DHCP Relay Agent (option 82) configuration..................................................................17
3 Saving configuration................................................................................................................20
Adding new ONTs ....................................................................................................................21
1 Automatic ONT activation configuration................................................................................21
2 Manual ONT activation............................................................................................................21
Configuration of VoIP on the ONT ..........................................................................................23
Using a predefined ONT configuration without using EasyMode.........................................25

 LTP EasyMode manual 3.38.0

Notes and warnings

Notes contain important information, tips, or recommendations on device operation and setup.



Warnings are used to inform the user about harmful situations for the device and the user alike, which

could cause malfunction or data loss.



 LTP EasyMode manual 3.38.0

•

1 LTP-X EasyMode description

EasyMode is a function set of LTP optical terminals. EasyMode is dedicated to fast GPON deployment

according to realized service model. EasyMode allows providers to configure Triple-Play services promptly.

EasyMode can be used for:

Acquaintance with GPON technology and Eltex equipment;

Fast testing of the main capabilities of the equipment;

Automatic configuring of the equipment on a network.

 LTP EasyMode manual 3.38.0

2 Software and hardware requirements

The EasyMode is supported by the hardware of B and C revisions and by NTU terminals. For EasyMade

operation, it is necessary to use the software no below than:

For LTP-8X(4X) 3.26.1

ForNTU-1 3.24.0

ForNTU-2W 3.25.1

ForNTU-2V(C), NTU-RG-1402G-W 3.25.2

ForNTU-RG-1421(31)G-Wac 3.28.1

 LTP EasyMode manual 3.38.0

3 Installation and connection

To familiarize yourself with the hardware of the device, the installation and connection procedure, refer to the

'LTP Operation Manual', which you can find at the linkhttps://eltex-co.com/catalog/olt_gpon/.

 LTP EasyMode manual 3.38.0

4 Connection to the terminal

Connection to LTP is possible either with a console cable or with an Ethernet cable to the GE port.

4.1 Console cable connection

For LTP rev.B, the RS-232 cable DB9(F) – DB9(F), which is included in the delivery, is used. The port is located

on the left side of the front panel, as shown in Figure 1 – Front panel of the LTP rev.B.

Figure 1 – Front panel of the LTP rev.B

For LTP rev.C, the RS-232 cable RJ-45 – DB9(F), which is included in the delivery, is used. The port is located

on the left side of the front panel, as shown in Figure 2 – Front panel of the LTP rev.C.

Figure 2 – Front panel of the LTP rev.C

Table 1 – Description of connectors, LEDs and controls located on the front panel of LTP rev.B

# Front panel element Description

1 Console RS-232 console port for local control of the device

2 GE Port 0..3 4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-8X)

3 Combo GE 0..3 4 chassis for SFP modules of 1000Base-X uplink interface for

connection to IP networks (for LTP-4X)

4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-4X)

4..7 4 chassis for SFP modules of 1000Base-X uplink interface for

connection to IP networks (for LTP-8X)

4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-8X)

 LTP EasyMode manual 3.38.0

•

# Front panel element Description

4 10G/1G 0..1 2 chassis for SFP modules of 10GBase/1000Base-X uplink

interface for connection to IP networks

5 PON 4 chassis for SFP modules of xPON 2.5 G (for LTP-4X)

8 chassis for SFP modules of xPON 2.5 G (for LTP-8X)

6 Power Device power LED

7 Status Device operation indicator

8 F Functional key that reboots the device and resets it to factory

default configuration:

pressing the key for less than 10 seconds reboots the

device;

pressing the key for more than 10 seconds resets the

device to factory default configuration.

Configuring the response to a button click is done in the CLI of the

terminal.

Table 2 lists connectors, LEDs and controls located on the front panel of LTP rev.C.

Table 2 – Description of the connectors, LEDs, and controls located on the front panel of LTP rev.C

# Front panel element Description

1 Power Device power LED

2 Status Device operation indicator

3 Fan Fan operation LED.

4 RPS Redundant power supply LED.

 LTP EasyMode manual 3.38.0

# Front panel element Description

5 Console Console port for local management of the device.

Connector pinning:

· not used

· RX

· GND

· TX

· not used

6 F Functional key that reboots the device and resets it to factory

default configuration:

· pressing the key for less than 10 seconds reboots the device;

· pressing the key for more than 10 seconds resets the device

to factory default configuration.

Configuring the response to a button click is done in the CLI of

the terminal.

7 GE Port 0..3 4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-8X)

8 Combo GE 0..3 4 chassis for SFP modules of 1000Base-X uplink interface for

connection to IP networks (for LTP-4X)

4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-4X)

4..7 4 chassis for SFP modules of 1000Base-X uplink interface for

connection to IP networks (for LTP-8X)

4 RJ-45 connectors of 10/100/1000Base-T Gigabit uplink

interfaces for connection to IP networks (for LTP-8X)

9 10G/1G 0..1 2 chassis for SFP modules of 10GBase/1000Base-X uplink

interface for connection to IP networks

 LTP EasyMode manual 3.38.0

# Front panel element Description

10 PON 4 chassis for SFP modules of xPON 2.5 G (for LTP-4X)

8 chassis for SFP modules of xPON 2.5 G (for LTP-8X)

Connect the cable and configure the following connection parameters:

Baud rate 115200

Data bits 8

Parity none

Stop bits 1

Flow Control none

For SecureCRT, the settings will be like in Figure 3.

Figure 3 – SecureCRT connection cofiguration

If the connection is successful, you will see a prompt to enter:

********************************************

* Optical line terminal LTP-4X rev.B *

********************************************

LTP-4X login:

Andere Handbücher für LTP-8X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ELTEX Touch-Terminal Handbücher

ELTEX

ELTEX NTU-2V Bedienungsanleitung

ELTEX

ELTEX NTU-RG-5402G-W Bedienungsanleitung

ELTEX

ELTEX TAU-32M.IP Bedienungsanleitung

ELTEX

ELTEX NTU-1 Bedienungsanleitung

ELTEX

ELTEX LTP-16N Merkblatt

ELTEX

ELTEX TAU-36.IP Bedienungsanleitung

ELTEX

ELTEX LTP-8X Bedienungsanleitung

ELTEX

ELTEX TAU-36.IP Bedienungsanleitung

ELTEX

ELTEX NTU-RG-1421G-WZ Bedienungsanleitung

ELTEX

ELTEX NTU-RG-5402G-W Kurzanleitung

ELTEX

ELTEX NTU-52V Bedienungsanleitung

ELTEX

ELTEX LTP-8X Installationshandbuch

ELTEX

ELTEX LTP-16N Bedienungsanleitung

ELTEX

ELTEX NTU-MD500P Bedienungsanleitung

ELTEX

ELTEX NTU-RG-1421G-Wac Bedienungsanleitung

ELTEX

ELTEX ONT NTU-1 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung