Elumen8 DB1300 Bedienungsanleitung

Order codes: ELUM065

DB1300 DMX Stage Blinder

User Manual

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Safety advice & installation

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablemainssupplyvoltageis

240VAC,50Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesandlampsofthesametypeandrating.

• ThisdevicefallsunderprotectionclassI.Thepowerplug

mustonlybepluggedintoaprotectionclassIoutlet.The

voltageandfrequencymustbeexactlythesameasstated

onthexture.Incorrectvoltagesorpoweroutletscanlead

tothedestructionofthextureandtoelectricshocks.

• Duringtheinitialstart-upsomesmokeorsmellmayarise.

Thisisanormalprocessanddoesnotnecessarilymean

thatthextureisdefective.

• CAUTION!Duringtheoperation,thehousing/lamps

becomeextremelyhot.

• Thisdeviceisdesignedforprofessionaluseonly

e.g.onstages,indiscothequesandtheatresetc.

• Themaximumdutycycleis1minute(fullon).Afterwards,

switchthedeviceoffandletitcooldownfor3minutes.

• Thexturemustneverbeoperatedorstockpiledin

surroundingswheresplashwater,rain,moistureorfog

mayharmthedevice.Moistureorveryhighhumidity

canreducetheinsulationandleadtoelectricshocks.

Whenusingsmokemachines,makesurethextureis

neverexposedtothedirectsmokejetandisinstalledin

adistanceof0.5mbetweenthesmokemachineandthe

xture.Theroommustonlybesaturatedwithanamount

ofsmokewherethevisibilityisstillgreaterthan10m.

• Neverusethisxtureduringthunderstorms.Overvoltage

coulddestroythexture.Alwaysdisconnectthedevice

duringthunderstorms.

• Thesymbol determinestheminimum

distancefromlitobjects.Theminimumdistance

betweenlightxtureandtheilluminatedsurface

mustbemorethan2m.

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Safety advice & installation

CABLE/LAMP INSTALLATION

Before replacing the lamp, unplug the mains lead and let the lamp cool down (for approx. 20 minutes).

Duringtheinstallationdonottouchtheglassbulbsbare-handed!Pleasefollowthelampmanufacturersnotes.

Donotinstalllampswithahigherwattage.Lampswithahigherwattagegeneratetemperaturesthextureisnotdesignedfor.

Damagescausednon-observancearenotsubjecttowarranty.

Forinstallationyouwillneed2xPar36650W120VDWElamps(Ordercode:LAMP91).

Duringtheoperation,thelampreacheshightemperaturesofupto400°C.



To install/replace the lamp follow the procedure below:

Step 1:Unscrewthelampcover.

Step 2:Ifreplacingthelamp,removetheoldlampfromthehousingandloosenthescrewsandwires.

Step 3:LoosenthescrewsontheonthenewPar36650W120VDWElampwithanappropriatescrewdriver.

Step 4:Connectthewirestothelampusinganappropriatescrewdriver.

Step 5Tightenthescrews.

Step 6:Insertthelampintothehousing.

Step 7:Screwthelampcoverbackontothexture.

• Thisxtureisonlyallowedtobeinstalledusingthe

suppliedmountingbracket.Inordertosafeguardsufcient

ventilation,leave0.5moffreespacearoundthedevice.

• Thehousingmustnevertouchsurroundingsurfacesor

objects.

• Alwayssecurethexturewithanappropriatesafetywire

asasecuritysafetymeasure.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• Thislightingxtureisforprofessionaluseonly-itis

notdesignedfororsuitableforhouseholduse.The

productmustbeinstalledbyaqualiedtechnicianin

accordancewithlocalterritoryregulations.Thesafetyof

theinstallationistheresponsibilityoftheinstaller.The

xturepresentsrisksofsevereinjuryordeathduetore

hazards,electricshockandfalls.

• WARRANTY:Twoyearsfromdateofpurchase.

Thisdoesnotapplytolampsortriacdevices.

DB1300 Stage Blinder, 2 x Par 36 650W

120V DWE Lamps, 240V connection

The connection cable must have a

diameter of at least 3 x 1.00mm2.

CAUTION!

THE LAMP HAS TO BE

REPLACED WHEN IT IS

DAMAGED OR DEFORMED

DUE TO THE HEAT.

DWE

120V/650W

DWE

120V/650W

240V

ENLNL

DANGER TO LIFE!

THE INSTALLATION MUST

ONLY BE CARRIED OUT BY

A QUALIFIED TECHNICIAN.

DO NOT OPERATE THIS

FIXTURE WITHOUT THE

LAMP CLOSED.

DANGER TO LIFE!

ONLY INSTALL LAMPS WITH

THE FIXTURE SWITCHED OFF!

UNPLUG FROM THE MAINS

BEFORE INSTALLING LAMPS.

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

CONNECTION WITH THE MAINS

Connectthexturetothemainswiththepowerplug.Theoccupationoftheconnectioncablesisasfollows:



Attention! Theearthhastobeconnected.

Ifthedevicewillbedirectlyconnectedwiththelocalpowersupplynetwork,adisconnectionswitchwithaminimumopening

of3mmateverypolehastobeincludedinthepermanentelectricalinstallation.

ThedevicemustonlybeconnectedwithanelectricinstallationcarriedoutincompliancewiththeIECstandards.Theelectric

installationmustbeequippedwithaResidualCurrentDevice(RCD)withamaximumfaultcurrentof30mA.

CONNECTION WITH THE MAINS

Ifthelampburnsout,thene-wirefuseofthexturemightfusetoo.Onlyreplacethefusebyafuseofthesame

typeandrating.

Before replacing the fuse, unplug the mains lead.

To replace the fuse follow the procedure below:

Step 1:Unscrewthefuseholderontherearpanelwithanappropriatescrewdriverfromthehousinganti-clockwise.

Step 2:Removetheoldfusefromthefuseholder.

Step 3:Installthenewfuseinthefuseholder.

Step 4:Replacethefuseholderinthehousingandscrewitbackin.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

Cable Pin International

Brown Live L

Blue Neutral N

Yellow/Green Earth

Safety advice & installation

DANGER TO LIFE!

WHEN INSTALLING THE FIXTURE, MAKE SURE THERE IS NO

HIGHLY-INFLAMMABLE MATERIAL WITHIN A MINIMUM DISTANCE OF 0.5m.

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Product overview & technical specications

TheeLumen8DB1300Blinderfeaturesanintegral,1CHDMXdimmerallowingtraditionalblinderstobeadded

intolightingrigswithoutanybulkydimmerracks.Utilisingindustrystandard650WDWEMFLlampswiredinseries

the2-cellblinderdeliversthewarmtonesofhalogenfromacompact,ruggedchassis.Idealforuseonstage.

•2x120V650WDWElampswiredinseries

(Ordercode:LAMP91-notsupplied)

•Beamangle:40°x30°

•7699Lux@2m(fullon)

•DMXchannels:1

•Dimming,autoandmaster/slavemodes

•Dipswitchmode/addressselection

•0-100%dimming

•Captivepowerconnectionttedwitha13AUKplug

•3-PinXLRinput/output

•Convectioncooled

DB1300 DMX 2 Cell Stage Blinder

Specications DB1300 Stage Blinder

Powerconsumption 1320W

Max.ambienttemperatureTa45°C

Max.distancefromammablesurfaces 0.5m

Minimumdistancetolitobject 2m

Dutycycle 1minute(fullon)

Coolingtime 3minutes

Powersupply 240V,50Hz

Fuse F8A250V

Dimensions 225x390x175mm

Weight 3.2kg

Ordercode ELUM065

175mm

190mm

225mm

325mm

390mm

0m 1m 2m 3m 4m 5m

30800 7699 3420 1930 1230

40 x 30 °

Lux

40 x 30°

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

POWER INPUT:

230V AC~50Hz

DB1300

DMX 2 Cell Stage Blinder

FUSE:

F8A 250V

DMX OUTPUT DMX INPUT

CAUTION!

During operation the unit and lamps become extremely hot!

Read the user manual carefully before use.

Never look directly into the light source.

Before opening the housing/replacing the lamp make sure

the xture is off and disconnected form the mains.

Keep away from rain and moisture.

Lamp: 2 x Par 36 650W 120V DWE

Duty cycle: 1 minute full on, 3 minutes rest

Ta=45°C

TC=410°C

DMX pinout:

1: Ground

2: Signal (-)

3: Signal (+)

09 01 06 07 02 03 05 0409

Technical specications

01-Earthpoint

02-Dipswitches

03-DMXsignalindicator

04-3-PinDMXinput

05-3-PinDMXoutput

06-Captivepowerconnection

07-FuseF8A250V

08-Hangingbracket

09-Hangingbracketadjustableknob

Inthebox:1 x xture

& 1 x user manual

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Operating instructions

Tosetthextureinto“Manual

Mode”,setdipswitches“9”and

“10”tothe“ON”position.The

brightnessofthetwolampscan

thenbeadjustedviadipswitches

“5” to“8”.

Tosetthextureinto“Auto

Mode”,setdipswitch“10”tothe

“ON”position.Thedimspeedof

thetwolampscanthenbead-

justedviadipswitches“1” to“8”.

Whendipswitches“1” to“8” are

“ON”thedimspeedisveryslow.

Whendipswitches“1” to“8” are

“OFF”thedimspeedisveryfast.

Tousethexturein“DMX

Mode”,usedipswitches“1”

to“9”tosetthedesiredDMX

address.

Addressing

Eachdeviceoccupies1channel.Toensurethatthecontrolsignalsareproperlydirectedtoachdevice

thexturerequiresaddressing.Thisneedstobechangedforeveryxturebychangingthedipswitches

assetoutinthetablebelow.Thestartingaddressisdenedastherstchannelfromwhichthe

devicewillrespondtothecontroller.Pleasemakesurethatyoudonothaveanyoverlappingchannelsin

ordertocontroleachxturecorrectlyandindependentlyfromanyotherxtureontheDMXdatalink.If

two,three,ormoredevicesareaddressedsimilarly,theywillworksimilarly.

Controlling

Afterhavingaddressedall

devices,youmaynowstart

operatingtheseviayour

controller.

Manual mode: Auto mode: DMX mode:

12345678 9 10

Dark Bright

12345678 9 10

Speed

Slow Fast

12345 6 78 9 10

DMXAddress

Dipswitchnumber 1 2345 6 78 9

DMXstartingaddress 1 24816 32 64 128 256

Occupation of the dipswitches:

Fixture1-Channel1 ON

OFF

Fixture4-Channel4 ON

OFF

Fixture5-Channel5 ON

OFF

Fixture2-Channel2 ON

OFF

Fixture3-Channel3 ON

OFF

Channel Value Function

1 000-255 Masterdimmer

(0-100%)

1 channel mode

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

DMX dipswitch quick reference chart

DMX DIPSWITCH SET

0 = OFF

1 = ON

#9 0000000011111111

#8 0000111100001111

#7 0 0 1100110011001 1

#6 0101010101010101

#1 #2 #3 #4 #5

00000 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480

10000 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

010 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

11000 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

0010 0 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

1010 0 537 69 101 133 165 197 229 261 293 325 357 389 421 453 485

0110 0 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

1110 0 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

00010840 72 104 136 168 200 232 264 296 328 360 392 424 456 488

10010941 73 105 137 169 201 233 265 297 329 361 393 425 457 489

0101010 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

1101011 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

0011012 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

1011013 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

0111014 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

1111015 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

0000116 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

1000117 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

0100118 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

1100119 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

0010120 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

1010121 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

0110122 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

11101 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

0001 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

1001 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

0101 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

1101 1 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

001 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

101 1 1 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

01 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

11111 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

Operating instructions

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Note: DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk DB1300 DMX Stage Blinder User Manual

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterference.Itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

Inhaltsverzeichnis

Andere Elumen8 DJ-Equipment Handbücher

Elumen8

Elumen8 ELUM107 Bedienungsanleitung

Elumen8

Elumen8 Evora CMY470 Hybrid Bedienungsanleitung

Elumen8

Elumen8 Virtuoso 1000 Profile WW Bedienungsanleitung

Elumen8

Elumen8 MP 15 LED Fresnel DTW Bedienungsanleitung

Elumen8

Elumen8 Evora 600 Beam Bedienungsanleitung

Elumen8

Elumen8 Endura 1Q120 Bedienungsanleitung

Elumen8

Elumen8 ELUM085 Bedienungsanleitung

Elumen8

Elumen8 9RE Beam Bedienungsanleitung

Elumen8

Elumen8 Titan Beam T3 Bedienungsanleitung

Elumen8

Elumen8 MP180 LED Fresnel RGBALC Bedienungsanleitung

Elumen8

Elumen8 Kudos 350ZS Bedienungsanleitung

Elumen8

Elumen8 Kudos 700 Beam Bedienungsanleitung

Elumen8

Elumen8 Kudos 60 Beam Bedienungsanleitung

Elumen8

Elumen8 Evora 850 Zoom Spot Bedienungsanleitung

Elumen8

Elumen8 Virtuoso 2000 Fresnel RGBAL Bedienungsanleitung

Elumen8

Elumen8 MP60 LED Fresnel WW Bedienungsanleitung

Elumen8

Elumen8 TZ 250PC WW Bedienungsanleitung

Elumen8

Elumen8 tz250 Bedienungsanleitung

Elumen8

Elumen8 Evora 500 Spot Bedienungsanleitung

Elumen8

Elumen8 Endura 1Q60 RGBW COB Exterior Fixture Bedienungsanleitung

Elumen8

Elumen8 Evora Zoom Spot CMY300 Bedienungsanleitung

Elumen8

Elumen8 ELUM021 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung