Emaux SSCnano Bedienungsanleitung

USER MANUAL

SSCnano

INSTALLATION AND OPERATION

MANUAL

Model: SSCnano

SAA

EMSW23101 285

DIRECTIVE

2011/65/Eu

SSCnano

FOR ABOVE AND INGROUND POOL

TABLE OF

CONTENT

PAGE

....

P1 CONTENT

4. TROUBLESHOOTING

5. SPARE PARTS LIST

....

6. TERMS OF THE WARRANTY

....

1. PRODUCT INTRODUCTION

.... WARNING

....

2. SPECIFICATIONS

2.2 ACCESSORIES

2.1 DIMENSION

3. INSTALLATION & OPERATION

3.1 INSTALLATION

3.2 OPERATION

3.1 .1 CONNECT WITH 50MM (1½”) UNION

3.1

38MM(1½”) FLEXI HOSE CONNECTOR

.2 CONNECT WITH THE 32MM(1¼”) &

3.2 .1 ON / OFF

3.2 .2 CHLORINE PERCENTAGE

3.2 .3 TIMER

........

3.2 .4 MEMORY MODE

WARNINGS P2

1. PRODUCT INTRODUCTION

SSCnano is an innovative inline salt chlorinator that seamlessly synchronizes with the pump. With its

preset timer offering flexible options and 4 chlorine production modes, SSCnano provides complete

control over the chlorination process. Enjoy the benefits of long cell life and reduced chemical usage,

thanks to its efficient and environmentally friendly design. Compact and user-friendly, SSCnano

revolutionizes the experience of chlorine production.

Salt chlorination is a method of sanitizing swimming pools with chlorine generated by electrolysis.

The electrolysis is achieved by passing the salt water solution through a weak electric charge in an

electrolytic cell, which converts sodium chloride (salt) in the water into chlorine gas. The gas is

dissolved in the water and becomes sodium hypochlorite (liquid chlorine).

This product should be installed and repaired by a technician who is

qualified in the installation and maintenance of pool/spa products.

Please read this manual before installing the product. The instructions in

this manual can be followed exactly. Disconnect electrical power before

removing the cover for servicing unit. Replace all screws and covers

before reconnecting the unit to electric power. Incorrect installation

and/or operation can cause serious injury, property damage, or death. To

reduce the risk of injury, do not permit children to use this product.

Improper installation and/or operation will void the warranty.

WARNINGS

2. SPECIFICATIONS

9130045 SSCnano4

110 -240V

/50-60 Hz

3500

ppm

4g/hr

2.5 bar

1.5”/ 50mm

and

32mm& 38mm

union

10-45°C3

m³/hr

20m³

9130046 SSCnano6 6g/hr 30m³

9130047 SSCnano8 8g/hr 40m³

9130048 SSCnano10 10g/hr 50m³

Code Model

Input

Voltage/

Frequency

Salt

Level

Cell

Production

Rate

Maximum

Working

Pressure

Cell

Connections

Working

Temperature

Min.

Flow

Max

Pool

Volume

200

310

214

249

134

138 138

134

173

105

P3 SPECIFICATIONS

2. 1 DIMENSION(mm)

2. 2 ACCESSORIES

32mm(1¼”) &

38mm(1½”) Flexi hose

connector

50mm (1½”) union Mounting Stand

[Fig.1] Stand and Wall Mount

105

32mm(1¼”) & 38mm(1½”) Flexi hose connector and 50mm (1½”) union installation,

please refer to Part 3, Installation & Operation.

The mounting stand is allowed the SSCnano place stand on the floor or wall mount.

INSTALLATION & OPERATION P4

3. INSTALLATION & OPERATION

Check the pool system regularly and make sure the parameters are within the range:

Salinity

3,000 to 4,000 ppm

pH level 7.2 to 7.4

Water temperature

10 - 45°

Flow rate 3 to 10 mᶾ/h

Target range

Parameter

3. INSTALLATION1

The SSCnano has an arrow mark on its body [Fig.2]

showing the water flow direction. It is designed to

operate with water flow rates between 3-10 mᶾ/h.

Please refer to the pipe manufacturer specifications for

recommended maximum flow rate. It is a must to use a

bypass loop with flow control valve if the flow rate is

over 8 mᶾ/h. [Fig.3] showing the general installation.

Adding a valve before and after SSCnano to make sure

the isolation between SSCnano and the facilitate when

maintenance. [Fig.2]

[Fig.3]

P5 INSTALLATION & OPERATION

3.1.1 CONNECT WITH 50MM (1½”) UNION

3.1.2 CONNECT WITH THE 32MM(1¼”) & 38MM(1½”)

FLEXI HOSE CONNECTOR

SSCnano can be installed either horizontal or vertical. The

union is designed for imperial 1½” pipe and metric 50mm pipe.

Pipes are required gluing to fix.

[Fig.4]

[Fig.5]

The 32mm(1¼”) & 38mm(1½”) Flexi hose

connector can let the SSCnano use with

flexible pipes, shown as [Fig.6].

3. OPERATION2

3.2.1 ON / OFF

OFF

Press once

Default

Press twice

[Fig.6]

3.2.2 CHLORINE PERCENTAGE

Optimize the chlorine percentage, to suit pool size/ temperature.

If the pool size is smaller than the max pool size of the SSCnano, lower the chlorine percentage

proportionally. (e.g. Using SSCnano4 for a 10m³ pool, press twice to 50% of the max chlorine

percentage rate.)

100%, the light is off

75%, the light flashes once

Press

four times

50%, the light flashes twice

25%, the light flashes three times

Press once

Press twice

Press three times

Default

The light will turn on after

the flash,

chlorine percentage.

running with

0 hour, the light is off

4 hours, the light flashes once

Press

four times

8 hours, the light flashes twice

12 hours, the light flashes three times

Press once

Press twice

Press three times

Default

The light will turn on after

the flash, running with timer.

Operating during winter:

The lower the water's temperature, the lower the salt water's conductivity will be. This in turn will

cause the SSCnano to work much harder than normal to produce chlorine. Algae and bacteria don't

grow well in cold environments. Thus, very little chlorine is needed, simply adjust the chlorine

percentage to an ideal rate.

During winter (e.g. temperature drops below 16℃), you can reduce to 25 % of the max chlorine

percentage to minimize chlorination for your pool.

Low-temperature protection:

When the water temperature is below 10℃, SSCnano will stop functioning. ( , NaCl light will flash,

refer to Part 4, Troubleshooting). This feature prolongs the service life of the cell.

3.2.3 TIMER

The timer setting can synchronize with the expected operation time for energy saving. (e.g. To set

the timer ON at 9:00 and off at 17:00. When it is 9:00 a.m., press  twice to set the timer of SSCnano

to 8 hours. It will stop running at 5:00 p.m. and function again at 9:00 a.m. the next morning.)

Note:

1) All setting will be saved when press ON/OFF to power off the SSCnano.

2) Power cut SSCnano will reset all settings to factory default.

INSTALLATION & OPERATION P6

3.2.4 MEMORY MODE

This function is for connecting the SSCnano to an automation system device. The SSCnano will start

chlorine generation once powered up. The chlorine percentage setting will be saved after power

down. (e.g. The chlorine percentage of the SSCnano was set to 50%. The setting will be kept if the

power is cut and turned back on.)

Note: The set time will not be saved and reset to default when power down.

To enter memory mode:

During OFF stage, press and hold for 5 seconds to enter the memory mode. (The light will flash three

times. It will flash once every 30 seconds if the SSCnano is running in memory mode.)

To cancel memory mode:

During ON stage, press and hold for 5 seconds to cancel the memory mode. (The light will flash three

times after canceling the mode and then stop.)

P7 INSTALLATION & OPERATION

4. TROUBLESHOOTING

LIGHT FLASH

CONTINUOUSLY POSSIBLE CAUSE SOLUTION

The normal operating range is

3,000 to 4,000 ppm. Add salt to

pool to achieve 3500 ppm to

ensure. Once the correct level has

been reached. The chlorinator

should operate normally.

The normal operating flow rate

range is between 3 to 10 mᶾ/h.

Make sure the flow rate is

sufficient. The bypass is proving

enough water to the cell and the

valves are correctly set.

If all the above were confirmed,

the flow sensor might have fatal

error, contact customer support

for a replacement.

Make sure the temperature is

between 10 to 45℃.

If the above were confirmed, the

temperature sensor might have a

fatal error, contact customer

support for a replacement.

Check the wiring connection, and

restart SSCnano.

If all the lights still flash, please

contact customer support for a

replacement.

Make sure the power supply is

connected and input the correct

voltage [110-240V, 50-60Hz].

If it still having no function,

please contact customer support

for a replacement.

Low salinity level. Salinity

below 2500ppm, causing the

production rate of chlorine is

being reduced.

No flow/ Flow rate too small/

error in flow sensor

Water temperature is not

within the operating range or

error in temperature sensor

Cell lifetime ran out

Wiring issues

NaCl

All lights are flashing

No function

Make sure the unit is connected

to the SSCnano paired adaptor.

Incorrect input voltage

NaCl , ,

P8TROUBLESHOOTING

, ,

5. SPARE PARTS LIST

Key

No.

Part

No. Description QTY

530135108

Electrolytic cell nut

E1330069

SSCnano4 Electrolytic cell （4 grams)

SSCnano6 Electrolytic cell（6 grams)

SSCnano8 Electrolytic cell（8 grams)

SSCnano10 Electrolytic cell（10 grams)

SSCnano PCB

111010013

SSCnano O-Ring

111040010

D116.6X1.5 O-Ring

5300410081

Electrolyser housing

111202472

O-Ring D70 x d60 x 6

430170991

2.0" Union Nut (black)

430300943

1.5" Union

111142481

O-Ring d42x3

430091071

32x38 Union

5203410081

Stand

5203410083

Mounting Stand Base

DC power supply（4 & 6 grams)

DC power supply（8 grams)

DC power supply（10 grams)

678

power supply

E1330070

E1330071

E1330072

106090062

106090063

106090064

1062510186

P9 SPARE PARTS LIST

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere emaux Wasserfiltersystem Handbücher

emaux

emaux SSC one Bedienungsanleitung

emaux

emaux NT-UV Series Bedienungsanleitung

emaux

emaux S1000 Bedienungsanleitung

emaux

emaux EM2837 Sicherheitsleitfaden

emaux

emaux MER150-100S Bedienungsanleitung

emaux

emaux V350 Bedienungsanleitung

emaux

emaux ICF 230 Bedienungsanleitung

emaux

emaux FSCO Series Bedienungsanleitung

emaux

emaux GALAXY IDE Series Bedienungsanleitung

emaux

emaux SSC mini Bedienungsanleitung

emaux

emaux CLL Series Bedienungsanleitung

emaux

emaux TMG Series Bedienungsanleitung

emaux

emaux ICF 100 Bedienungsanleitung

emaux

emaux V700B Bedienungsanleitung

emaux

emaux EM2861 Sicherheitsleitfaden

emaux

emaux NL1200 Bedienungsanleitung

emaux

emaux EM2817V Series Handbuch

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung

emaux SSCnano Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken