Embraco Fullmotion CF10C Bedienungsanleitung
FULLMOTION COMPRESSORS
ELECTRONIC INVERTER
Product Manual
Fullmotion CF10C
www.embraco.com October, 2018 Revision 2.1
BEFORE YOU BEGIN
!!
WARNING
!!
NOTICE
CAUTION
!!
Incorrect operation could result in bod-
ily injury or death due to electrical haz-
ard.
!!
WARNING
!!
NOTICE
CAUTION
!!
Incorrect operation could cause bod-
ily injury or could result in equipment
damage.
!!
WARNING
!!
NOTICE
CAUTION
!!
Contain helpful suggestions or refer-
ences to material not covered in this
document.
Contents
1 INTRODUCTION 1
1.1 Productdescription ............................. 2
1.1.1 Stand alone inverter . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1.2 Instituteapproval.......................... 2
1.2 VNE compressor series description . . . . . . . . . . . . . . . . . . . . 3
1.3 FMF and VEG compressor series description . . . . . . . . . . . . . . . 4
1.4 Producthandling............................... 4
1.5 Dimensions(mm) .............................. 5
1.5.1 FMF and VEG compressor series . . . . . . . . . . . . . . . . . 5
1.5.2 VNE compressor series . . . . . . . . . . . . . . . . . . . . . . . 6
1.6 Packageinformation............................. 6
2 TECHNICAL SPECIFICATIONS 8
2.1 Nomenclature ................................ 8
2.1.1 Labelinformation.......................... 9
2.2 Productspecications............................ 9
2.3 Inverterenclosure .............................. 11
2.3.1 Product dimensions . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3.2 Connectors.............................. 11
2.3.3 Productdiscards .......................... 14
2.4 Information about input inrush current . . . . . . . . . . . . . . . . . . 15
3 INSTALLATION 16
3.1 Assemblyinstructions............................ 16
3.1.1 VEG and FMF compressor cable connection . . . . . . . . . . 17
3.1.2 VNE compressor cable connection . . . . . . . . . . . . . . . . 19
3.1.3 Forced ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.4 Optional AC Fan switch control . . . . . . . . . . . . . . . . . . 24
3.1.5 Inverter cables arrangement . . . . . . . . . . . . . . . . . . . 25
3.1.6 Input cable with ferrite lter . . . . . . . . . . . . . . . . . . . . 27
3.2 Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4 OPERATION 29
4.1 Frequency control mode . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 Drop-Incontrolmode ............................ 31
4.2.1 First time Pull-down . . . . . . . . . . . . . . . . . . . . . . . . 32
4.2.2 Normalcycling............................ 32
4.2.3 Connection.............................. 32
CONTENTS
4.3 Serialcontrolmode ............................. 33
4.3.1 Serial specications and Internal Circuit . . . . . . . . . . . . . 33
4.3.2 Commands.............................. 35
5 DIAGNOSTICS 39
5.1 LEDindication ................................ 39
5.2 Troubleshooting ............................... 40
GENERAL PRECAUTIONS
!!
WARNING
!!
NOTICE
CAUTION
!!
• During instalation the environment must be prop-
erly protected against ESD. The operator and ma-
chines must be properly Earthed.
• Make sure that Fullmotion CF10C Inverter will not
be in direct contact with ames during assembly.
• The location where the Inverter will be installed
must be protected against splashed water from all
directions.
• Do not open the Inverter enclosure. For installa-
tion, remove only the Inverter Cover to make the
electrical connections.
!!
WARNING
!!
NOTICE
CAUTION
!!
• This inverter is for use only with the Fullmotion Em-
braco compressors.
• Read this material carefully before you begin the
Fullmotion CF10C Inverter installation and start up
procedure.
• To prevent damage to your inverter during and af-
ter assembly, avoid contacting with the following
substances: Hydrocarbons; Ester based oils (e.g.:
compressor oil); Phenols; Amines; Ketenes; Au-
tomotive uids such as grease, except glycol and
heavy alcohol.
!!
WARNING
!!
NOTICE
CAUTION
!!
• The protection against access to live parts have
been evaluated according to the relevant require-
ments from IEC 60335-1 and UL 60730-1.
Chapter 1
INTRODUCTION
Embraco’s Fullmotion compressors are ideal for commercial applications where
wide voltage range, fast pull down, better performance, ne temperature control,
lower power consumption and very low noise and vibration levels are required.
This is possible thanks to the use of an electronic inverter capable of driving the
compressor at dierent speeds and consequently, controlling its refrigeration ca-
pacity.
Eciency
Fullmotion Compressors technology al-
lows the compressor to operate at dif-
ferent speeds, adjusting it according to
demand. When side by side with a con-
ventional compressor, the energy con-
sumption is up to 45%.
Flexible
Indicated for commercial refrigeration
system, provides more exibility in cus-
tomized solutions through inclusion of
electronics already coupled to the com-
pressor, opening a wide variety of appli-
cations.
1
CHAPTER 1. INTRODUCTION 2
1.1 Product description
1.1.1 Stand alone inverter
1
2
3
4
Figure 1.1: Stand alone view
Composed by
Indicator Description
1 Plastic body
2 Plastic cover
3Compressor cable
output connection
4
Input/ Earth/
Communication
cables connection
!!
WARNING
!!
NOTICE
CAUTION
!!
CF10C inverter series are designed to
be used only in built in appliances, with
not accessible machine compartment.
1.1.2 Institute approval
Institute approval
CF10C Inverter Approved according to
EN 60335-1
CHAPTER 1. INTRODUCTION 3
1.2 VNE compressor series description
5
1.Product descripton
9
10
8
6
5
4
1
3
7
2
1- Fence cover
2- OLP
3- 3/4 OLP
4- Cord anchorage
5- Screw
6- Grommets
7- Compressor shell
8- Process tube
9- Discharge tube
10- Suction tube
!!
WARNING
!!
NOTICE
CAUTION
!!
• Before you begin your installation observe
technical specications and proper connec-
tions.
• Check if product is properly identied and if
it’s enclosure is without cracks.
CHAPTER 1. INTRODUCTION 4
1.3 FMF and VEG compressor series description
5
1
23
4
6
7
8
1-Fence cover
2-Cord anchorage
3-Screw
4-Grommets
5-Compressor shell
6-Process tube
7-Discharge tube
8-Suction tube
1
23
4
5
6
7
8
1.4 Product handling
!!
WARNING
!!
NOTICE
CAUTION
!!
• Inverter is sensitive to Electrostatic Dis-
charges. Take care with product handling
until nal assembly.
• Special care must be taken to avoid me-
chanical impacts on the inverter during
assembly process.
• The environment must be properly pro-
tected against ESD.
• The workers that handle the inverter must
be Earthed through adequate ESD wrist
strap and must wear ESD gloves.
• Do not hold by the wiring.
• Do not use the inverter if it drops during
handling.
CHAPTER 1. INTRODUCTION 5
1.5 Dimensions (mm)
1.5.1 FMF and VEG compressor series
173.3
85.5
133.3
217.3
(INVERTER)
199.5
241
202
Inhaltsverzeichnis
Andere Embraco Luftkompressor Handbücher
