EMC VNXe3100 Bedienungsanleitung

2/2/11 1

EMC®VNXe3100™

Replacing a VNXe3100 Memory Module

Before you start

Before you begin the replacement procedure, make sure you have correctly identified the faulted part,

and that a replacement memory module (DIMM) is available. Refer to your EMC® VNXe™ online help

(Servicing your system > Adding or replacing faulted hardware components > Replace a faulted

hardware component) for instructions on how to identify failures, order new parts, and handle

hardware components. Also, prepare your disk processor enclosure (DPE) for service as described

below.

Preparing your disk processor enclosure for service

IMPORTANT

To protect your VNXe system from accidental data loss while you remove and replace DPE

components, open Unisphere™ and select Settings, then Service System.

• Log in with your service password.

•IntheSystem Components column, select the storage processor (A or B) associated with the

faulted component.

•UnderService Actions, select Enter Service Mode, then Execute service action.

The storage processor fault LED will flash alternating amber and blue while the SP remains in

Service Mode and is receiving active power.

Contents

This document provides instructions on the following tasks:

Task 1: Remove the storage processor (SP) assembly on page 2

Task 2: Remove the SP assembly top cover on page 3

Task 3: Replace the memory module on page 4

Task 4: Replace the SP top cover on page 5

Task 5: Replace the storage processor on page 6

Task 6: Reboot the storage processor on page 7

Task 7: Verify the operation of the new module on page 7

Task 8: Return the faulted memory module on page 8

Replacing a VNXe3100 Memory Module2

Task 1: Remove the storage processor (SP) assembly

The memory modules reside on the storage processor printed circuit board (motherboard), within the

storage processor assembly. To replace a memory module, you must remove the SP assembly from the

chassis, and then remove its top cover to gain access to processor board components.

Follow these steps to remove the VNXe storage processor assembly:

CAUTION

DO NOT REMOVE a storage processor while the “Unsafe to remove SP” LED is on.

The light indicates that you may interrupt a vital system or data-caching process.

If your system has a single storage processor, DO NOT REMOVE the storage

processor if the “Unsafe to remove” LED for the cache protection module is on.

1. Disconnect the network and all other cables from the back of the assembly that includes the faulted

module. Do not remove any cables from the other storage processor assembly.

Mark the cables with the port numbers from which you removed them.

2. Locate the two orange release levers on the storage processor latches.

3. Squeeze the levers to release the latches and then pull the latches outward.

4. Pull out the latches until they are fully extended and the storage processor assembly is released from

its enclosure.

5. Use the latches to partially slide the assembly from its enclosure. When the storage processor is about

half-way out of its enclosure, use both hands to support the assembly and draw it fully out of the

enclosure.

6. Place the storage processor assembly on a clean, flat, static-free work surface.

CL4682

Task 2: Remove the SP assembly top cover 3

1. Press the blue button on the cover.

2. Push the cover back 1/4 inch.

3. Lift the cover up.

4. Unpack the replacement memory module and then place it on the same clean, flat, static free work

area.

Note: Retain the packaging to return the faulted module.

Task 2: Remove the SP assembly top cover

Replacing a VNXe3100 Memory Module4

Remove the memory module from the storage processor, and install the replacemen:.

1. Rotate the memory module latches outward to release the module from the socket.

2. Touching only the outside edges of the memory module, pull the module directly out of the socket,

and place it on an antistatic surface.

3. Remove the replacement memory module from its antistatic bag.

4. Handling only the outside edges of the module, align the module with the socket.

Note: The socket and module are keyed to prevent incorrect alignment.

5. Firmly push the module directly into the socket.

6. The latches will snap to the closed position when the module is fully inserted in its socket.

DIMM 0 DIMM 1

Task 3: Replace the memory module

Task 4: Replace the SP top cover 5

Replace the canister cover:

1. Align the cover tabs with the notches in the canister.

2. Slide it forward 1/4 inch until the tab secures the cover.

Task 4: Replace the SP top cover

Replacing a VNXe3100 Memory Module6

Replace the SP assembly in the enclosure:

1. Pull out the latches on each side of the SP and make sure they stay in the open position.

2. Align the SP with the chassis opening and push it straight into the chassis.

The latches begin to close when they contact the chassis edges.

3. Close the right and left latches to fully seat the SP in the chassis.

An audible click indicates that the latches are secure.

4. Reconnect the cables to the back of the storage processor.

• Connect all cables to the same ports from which you removed them on the faulted SP assembly.

• The SP begins powering up immediately after connection to an active AC power source.

CL4687

Task 5: Replace the storage processor

Task 6: Reboot the storage processor 7

Once you have replaced the faulted memory module and returned the storage processor assembly to

the chassis, reboot the recently serviced SP to ensure that it leaves Service Mode:

1. From Unisphere, select Settings, then Service System.

2. Log in with your service password.

3. In the System Components column, select the replaced storage processor (A or B).

4. Under Service Actions, select Reboot, then Execute service action.

Note: It may take several minutes for the system to complete its reboot and return to Normal Mode.

5. Refresh your browser, or follow the on-screen instructions, to bring the software out of Service Mode

and restore full-function Unisphere.

Verify that the new memory module is recognized by your system, and operating correctly:

1. In Unisphere, click View System Health.

2. Select the storage processor in the Component list or the graphical view:

• In the Component list, the memory should be marked with a status OK icon:

• In the graphical view, the SP is highlighted green.

Note: If the system health monitor shows the replacement module as faulted, contact your service

provider.

Task 6: Reboot the storage processor

Task 7: Verify the operation of the new module

Replacing a VNXe3100 Memory Module8

Return the faulted memory module to your service provider:

1. Package the faulted part in the shipping box that contained the replacement, and seal the box.

2. From Unisphere, click Support > Need more Help? > Customer replaceable parts > Return a

customer replaceable part to enter the EMC Online Support website. The site includes detailed

instructions on how to return the faulted part.

Note: If your screen does not show the Return a customer replaceable part option, contact your

service provider for instructions on what to do next.

3. Follow the on-screen instructions. The website includes a printable return label and box pickup

information.

4. Attach the shipping label, and contact the appropriate person to pick up the faulted part.

Part number: 300-012-220 A01

Published February, 2011

EMC believes the information in this publication is accurate as of its publication date. The information is subject to

change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Use, copying, and distribution of any EMC software described in this publication requires an applicable software license.

For the most up-to-date regulatory document for your product line, go to the Technical Documentation and Advisories

section on EMC Powerlink.

For the most up-to-date listing of EMC product names, see EMC Corporation Trademarks on EMC.com.

All other trademarks used herein are the property of their respective owners.

Task 8: Return the faulted memory module

Andere Handbücher für VNXe3100

Inhaltsverzeichnis

Andere EMC Server Handbücher

EMC

EMC Data Domain DD670 Gebrauchs- und Pflegehandbuch

EMC

EMC IS1200 Bedienungsanleitung

EMC

EMC Celerra Installationshandbuch

EMC

EMC SVR-I2U-R2312 Produkthandbuch

EMC

EMC VPLEX with GeoSynchrony 4.2 Montageanleitung

EMC

EMC SVR-I2U-H2316 Produkthandbuch

EMC

EMC SVR-I1U-1304 Produkthandbuch

EMC

EMC Avamar Data Store Gen4T Bedienungsanleitung

EMC

EMC Connectrix B Series Kurzanleitung

EMC

EMC SVR-I1U-1208 Produkthandbuch

EMC

EMC CLARiiON 300002039 Bedienungsanleitung

EMC

EMC CLARiiON Bedienungsanleitung

EMC

EMC Data Domain DS60 Montageanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung