Emerson KEYSTONE F635 Montageanleitung

3

12

11

5

6

7

1

8

9

10

2

4

KEYSTONE SLURRY CONTROL VALVES

FIGURE 635

Complete assembly and disassembly instructions for F635 slurry valves

DISASSEMBLY INSTRUCTIONS

1. Remove the valve from the pipeline. The disc should be in the closed position.

2. Disconnect any electric or pneumatic lines and remove the actuator.

3. Clean off all external deposits of slurry by steam cleaning or grit blasting.

4. Remove both gland nuts (12), gland plate (5) and gland collar (6).

5. Remove both gland studs (11) from the valve body (1).

6. Remove the end cover plate (9) and gasket(8).

7. Remove the disc screws (4). For valve sizes DN 50 - 300, there are two only disc screws.

For sizes DN 350 - 500, there are three. With the larger valves it is recommended that you

support the disc.

8. Drive out the shaft (3) using a brass or aluminium dolly from the bottom of the valve.

9. Remove the disc (2).

10. Remove all the old gland packing (7).

11. Thoroughly clean all components and examine them for excessive wear or damage, replacing

them where necessary.

12. Disassembly is now complete and ready for re-assembly. Refer to assembly instructions.

NOTE: DN 50 - 300 valve illustrated.

ASSEMBLY INSTRUCTIONS

1. Fit the graphite gasket (8) to the end cover(9).

2 Fit the end cover (8, 9, 10) to the bottom end of the valve body (1).

3 Pack the valve gland with graphite packing(7).

4 Fit both gland studs (11) after first coating them with anti-seize compound.

5 Fit the disc (2) inside the valve bore, with the disc screw holes uppermost. (For 5 degree angled

seat option only, ensure that the disc is positioned so that the valve will close in the anti-clock

wise direction, looking from the top of the valve.)

6 Fit the gland plate (5) and the gland collar (6) to the shaft (3).

7 Insert the shaft assembly (3, 5 and 6) through the body (1) and disc (2), ensuring that the shaft

and disc screw holes are aligned.

8 Fit and tighten the disc screws (4). For valve sizes DN 50 - 300, there are two only disc screws

for sizes DN 350 - 500, there are three.

9 Check that the disc is free to rotate. (For 5 degree angled seat options, check that the disc is

free to move from the open to the 5 degree closed position).

10. Tighten up the gland nuts (12) ensuring it is not overtightened.

11. Assembly is now complete and ready for installation. Refer to the F635 installation and

commissioning instructions.

12. The gland may need to be adjusted on plant start up.

© 2012 Emerson plc. All Rights Reserved.www.valves.emerson.com VCIOM-02909-EN 15/09

© 2017 Emerson. All rights reserved.

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Emerson Steuereinheit Handbücher

Emerson

Emerson Alco Controls TIH FLR Series Bedienungsanleitung

Emerson

Emerson Keystone 952 Bedienungsanleitung

Emerson

Emerson numatics E22 Bedienungsanleitung

Emerson

Emerson Fisher V270 Bedienungsanleitung

Emerson

Emerson Fisher 63EG-98HM Bedienungsanleitung

Emerson

Emerson ANDERSON GREENWOOD 5910C Bedienungsanleitung

Emerson

Emerson Anderson Greenwood M4TL Bedienungsanleitung

Emerson

Emerson Sempell series Bedienungsanleitung

Emerson

Emerson IC200UEM001 Bedienungsanleitung

Emerson

Emerson Fisher OS2 Bedienungsanleitung

Emerson

Emerson KTM RICHARDS FIGURE R384 Bedienungsanleitung

Emerson

Emerson Sapag 1100 Bedienungsanleitung

Emerson

Emerson KEYSTONE FIGURE 955 Bedienungsanleitung

Emerson

Emerson Neotecha NTB Bedienungsanleitung

Emerson

Emerson Fisher 8532 Bedienungsanleitung

Emerson

Emerson KEYSTONE 60 Series Bedienungsanleitung

Emerson

Emerson PACSystems IC695ACC302 Bedienungsanleitung

Emerson

Emerson Fisher N551 Bedienungsanleitung

Emerson

Emerson Bettis OM3 Bedienungsanleitung

Emerson

Emerson Fisher Control-Disk NPS 14 CL150 Bedienungsanleitung

Emerson

Emerson Fisher MR98LD Bedienungsanleitung

Emerson

Emerson Clarkson ZP300 Bedienungsanleitung

Emerson

Emerson YARWAY B Handbuch

Emerson

Emerson Dixell XEV20D Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung