Emerson Advantage 2.1 Bedienungsanleitung

Table of Contents

Advantage 2.1 Actuator Installation and Operation Manual 1

Table of Contents

Introduction and Safety .......................................................................................................... 2

Safety message levels ............................................................................................................ 2

User health and safety ............................................................................................................ 2

Transportation and Storage ................................................................................................... 4

Handling and unpacking guidelines ........................................................................................ 4

Storage, disposal, and return requirements ............................................................................ 4

Product Description ................................................................................................................ 5

Actuator identification .............................................................................................................. 5

Bonnet description .................................................................................................................. 6

Valve diaphragm identification ................................................................................................ 6

Installation ............................................................................................................................... 8

Precautions ............................................................................................................................. 8

Install the valve and topworks ................................................................................................. 8

Change the compressor, tube nut, and snap ring ................................................................... 9

Mount the topworks to the valve ............................................................................................ 10

Tighten the bonnet fasteners ................................................................................................ 10

Fastener torque table for valve body to topworks .................................................................. 11

Actuator operating pressure .................................................................................................. 11

Disassemble the valve .......................................................................................................... 11

Replace the valve diaphragm ................................................................................................ 11

Designed and Manufactured by ITT

Introduction and Safety

Advantage 2.1 Actuator Installation and Operation Manual2

Introduction and Safety

Safety message levels

Definitions

Safety message level Indication

DANGER: A hazardous situation which, if not avoided, will

result in death or serious injury

WARNING: A hazardous situation which, if not avoided,

could result in death or serious injury

CAUTION: A hazardous situation which, if not avoided,

could result in minor or moderate injury

Electrical Hazard: The possibility of electrical risks if instructions

are not followed in a proper manner

NOTICE: • A potential situation which, if not avoided,

could result in an undesirable result or

state

• A practice not related to personal injury

User health and safety

General precautions

This product is designed and manufactured using good workmanship and materials, and meets

all applicable industry standards. This product should be used only as recommended by ITT or

ASCO.

WARNING:

• Misapplication of the valve can result in injury or property damage. Select valves and valve

components of the proper materials and make sure that they are consistent with your

specific performance requirements. Incorrect application of this product includes but is not

limited to:

• Exceeding the pressure or temperature rating

• Failing to maintain this product according to the recommendations

• Using this product to contain or control media that is incompatible with the materials of

construction

Qualifications and training

The personnel responsible for the assembly, operation, inspection, and maintenance of the

valve must be appropriately qualified. The operating company must do the following tasks:

• Define the responsibilities and competency of all personnel handling this equipment.

• Provide instruction and training.

Designed and Manufactured by ITT

Introduction and Safety

Advantage 2.1 Actuator Installation and Operation Manual 3

• Ensure that the contents of the operating instructions have been fully understood by the

personnel.

Instruction and training can be carried out by ASCO as the reseller of the valve by order of the

manufacturer.

Non-compliance risks

Failure to comply with all safety precautions can result in the following conditions:

• Death or serious injury due to electrical, mechanical, and chemical influences

• Environmental damage due to the leakage of dangerous materials

• Product damage

• Property damage

• Loss of all claims for damages

Operational safety precautions

Be aware of these safety precautions when operating this product:

• Do not leave hot or cold components of the product unsecured against contact if they are a

source of danger.

• Do not remove the contact guard for moving parts when the product is in operation. Never

operate the product without the contact guard installed.

• Do not hang items from the product. Any accessories must be firmly or permanently

attached.

• Do not use the product as a step or hand hold.

• Do not paint over the identification tag, warnings, notices, or other identification marks

associated with the product.

Maintenance safety precautions

Be aware of these safety precautions when performing maintenance on this product:

• You must decontaminate the product if it has been exposed to harmful substances such as

caustic chemicals.

Use of unauthorized parts

Reconstruction or modification of the product is only permissible after consultation with ITT.

Genuine spare parts and accessories authorized by ITT serve to maintain safety. Use of non-

genuine ITT parts can annul liability of the manufacturer for the consequences. ITT parts are

not to be used in conjunction with products not supplied by ITT as this improper use can annul

all liability for the consequences.

Unacceptable modes of operation

The operational reliability of this product is only guaranteed when it is used as designated. The

operating limits given on the identification tag and in the data sheet may not be exceeded under

any circumstances. If the identification tag is missing or worn, contact ASCO for specific

instructions.

Designed and Manufactured by ITT

Transportation and Storage

Advantage 2.1 Actuator Installation and Operation Manual4

Transportation and Storage

Handling and unpacking guidelines

CAUTION:

Always observe the applicable standards and regulations regarding the prevention of

accidents when handling the product.

Handling guidelines

Follow these guidelines when handling the product to prevent damage:

• Use care when handling the product.

• Leave protective caps and covers on the product until installation.

Unpacking guidelines

Follow these guidelines when unpacking the product:

1. Inspect the package for damaged or missing items upon delivery.

2. Note any damaged or missing items on the receipt and freight bill.

3. Do not lift or pull on the electrical conduit lines. Doing so may cause the POC switches to

come out of calibration.

Storage, disposal, and return requirements

Storage If you are not immediately installing the product after delivery, store it as follows:

• Store the product in a dry room that maintains a constant temperature.

• Make sure that the products are not stacked on top of one another.

Disposal Dispose of this product and associated components in compliance with federal, state, and local

regulations.

Return Ensure these requirements are met before you return a product to ASCO:

• Contact ASCO for specific instructions on how to return the product.

• Clean the valve of all hazardous material.

• Complete a Material Safety Data Sheet or Process Data Sheet for any process fluid that

could remain on the valve.

• Obtain a Return Material Authorization from the factory.

Designed and Manufactured by ITT

Product Description

Advantage 2.1 Actuator Installation and Operation Manual 5

1For fail close actuators, codes are specific spring combinations.

2Series number equates to diaphragm effective area.

Product Description

Actuator identification

Design Overview The actuator is a spring or double acting pneumatic actuator.

To determine if you have an Advantage actuator or an Advantage actuator 2.1 locate the

spindle compressor connection and determine if you have a pin connection or modular

compressor design.

Figure 1: Pin connection

for Advantage actuator

Figure 2: Compressor for

Advantage 2.0 actuator

Figure 3: Modular compressor with snap

ring retention for Advantage 2.1

actuator

Model number The actuator model number is located on the ASCO identification tag. The model number is a

four digit number defining the actuator as follows.

Table 1: Actuator

Code Description

B Advantage 2.1 actuator

Table 2: Mode of operation

Code Description

1 Fail open (spring to open, air to close) (direct acting)

2 Fail close (spring to close, air to open) (reverse

acting)

3 Double acting (air to open, air to close)

Table 3: Actuator series

Code1Actuator series2

03, 04 3

05, 06 5

08, 09 8

16, 17 16

Table 4: Examples

Model number Description

B308 Advantage 2.1 actuator, double acting, series 8

B216 Advantage 2.1 actuator, fail close, series 16 with a

spring set

Designed and Manufactured by ITT

Product Description

Advantage 2.1 Actuator Installation and Operation Manual6

Identification tag

Line Description

1 Valve serial number

2 Valve size and model number

3 Valve diaphragm type

4 Maximum recommended actuation pressure

Bonnet description

Non-Sealed bonnetThe non-sealed bonnet has a weep hole that indicates a diaphragm failure by allowing process

fluid that accumulates in the bonnet to pass through the hole.

Sealed bonnet The sealed bonnet uses a special “V-notch” vent plug, which permits leak detection.

Figure 4: Weep hole and V-notch vent plug

Valve diaphragm identification

Diaphragm tab codes

All diaphragm materials and physical properties are batch traceable via permanent codes

molded into the diaphragm tabs. The molding date, grade of diaphragm, and size provide

traceability to original batch records.

Designed and Manufactured by ITT

Product Description

Advantage 2.1 Actuator Installation and Operation Manual 7

1. Date code

2. Supplier code

Figure 5: Elastomer diaphragm front

1. Valve size

2. Grade of diaphragm

Figure 6: Elastomer diaphragm back

1. Material code

2. Date code

Figure 7: PTFE diaphragm

Designed and Manufactured by ITT

Installation

Advantage 2.1 Actuator Installation and Operation Manual8

Installation

Precautions

WARNING:

• All procedures must be performed by qualified personnel.

• When the process fluid is hazardous, thermal (hot or cold), or corrosive, take extra

precautions. Employ the appropriate safety devices and be prepared to control a process

media leak.

• Always wear protective clothing and equipment to safeguard the eyes, face, hands, skin,

and lungs from the fluid in the line.

• Do not disassemble the actuator in the field. The actuator contains energized springs

which can cause injury. The product is designed to be recycled in its entirety.

CAUTION:

• Disconnect electrical, pneumatic, and hydraulic power before servicing actuator or

automation components.

Install the valve and topworks

NOTICE:

The topworks size and configuration can limit the actual operating pressure. Consult the Pure-

Flo catalog for pressure limitations. Consult the factory or engineering catalog for vacuum

operation.

Consider the following information before installing the actuator:

• The series 3, 5, 8, or 16 stainless steel bonnet Advantage 2.1 actuator can have the air

inlets positioned in any quadrant.

• The maximum valve operating pressure is 10.34 bar | 150 psig. This pressure is applicable

up to 38ºC | 100ºF. Valves at maximum pressure cannot be used at maximum

temperatures.

• The maximum actuator pressure is 6.2 bar | 90 psi.

1. If you have a weld end valve, then consider the following:

If you are welding ... Then ...

Manually Remove the topworks.

In line for schedule 10

or heavier pipe Remove the topworks.

In line for schedule 5

or lighter pipe and tub-

ing

You can weld with automatic equipment. Before you perform the weld:

1. Remove the topworks (optional).

2. If left installed, set the valve to the open position.

3. Properly purge the valve with an inert gas.

2. Install the valve.

If the valve is a ... Then ...

Dia-Flo diaphragm

valve For horizontal piping systems to be drained through the valve, install the valve

spindle between 0º and 30º above horizontal. For vertical piping systems, no

specific orientation is required.

Designed and Manufactured by ITT

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson Copeland EV2 Series Benutzerhandbuch

Emerson

Emerson Fisher easy-Drive 200R Bedienungsanleitung

Emerson

Emerson Fisher KC Series Bedienungsanleitung

Emerson

Emerson Dixell XM670K Verdrahtungsschema

Emerson

Emerson Fisher S200 Series Bedienungsanleitung

Emerson

Emerson EL-O-Matic F-Series Installations- und Betriebsanleitung

Emerson

Emerson Bettis XTE3000 Bedienungsanleitung

Emerson

Emerson KEYSTONE FIGURE 79U Handbuch

Emerson

Emerson Dixell XR03CH Verdrahtungsschema

Emerson

Emerson Fisher 1051 Bedienungsanleitung

Emerson

Emerson White-Rodgers 21M51U-843 Bedienungsanleitung

Emerson

Emerson PeC C100 Bedienungsanleitung

Emerson

Emerson DIXELL XD70T Verdrahtungsschema

Emerson

Emerson ControlWave Bedienungsanleitung

Emerson

Emerson ECD-002 Bedienungsanleitung

Emerson

Emerson FIELDVUE DVC6200f Bedienungsanleitung

Emerson

Emerson PMAC II Bedienungsanleitung

Emerson

Emerson Bettis RTS Bedienungsanleitung

Emerson

Emerson dixell XR60CX Verdrahtungsschema

Emerson

Emerson EL-O-Matic F-Series Bedienungsanleitung

Emerson

Emerson EXD-HP1/2 Bedienungsanleitung

Emerson

Emerson PACSystems RX3i IC695CPE302 Bedienungsanleitung

Emerson

Emerson Fisher 585CLS Bedienungsanleitung

Emerson

Emerson EC2-552 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung