Emerson Bettis GVO-C Series Bedienungsanleitung

SIL Safety Manual

SM-025-GVO Rev. 0

November 2017

Bettis GVO-C Series Pneumatic Actuators

GVO-CLP-SR/FS SIL Safety Manual

SIL Safety Manual

SM-025-GVO Rev. 0

Table of Contents

November 2017

Table of Contents

Section 1: Introduction

Section 2: Acronyms

Section 3: Functional Specification

Section 4: Product Description

4.1 GVO-CLP-SR/FS pneumatic linear spring return actuator general description 7

4.2 GVO-CLP-SR/FS working principle ................................................................. 8

Section 5: Service Condition Limitations (limitation of use)

Section 6: Expected Time

Section 7: Failure Modes and Estimated Failure Rates

Section 8: Periodic Text and Maintenance Requirements

8.1 General ....................................................................................................... 13

8.2 Full Stroke Test (Proof Test) ......................................................................... 13

8.3 Diagnostic Coverage / Proof Test Coverage ................................................. 15

8.4 Partial Stroke Test ....................................................................................... 16

8.5 Partial Stroke Diagnostic Coverage / Test Coverage ..................................... 19

8.6 Periodic Maintenance.................................................................................. 19

Section 9: Classification

Section 10: MRT

Section 11: Architectural Constraints

Section 12: Systematic Capability

Section 13: Manufacturer Notes

November 2017

SIL Safety Manual

SM-025-GVO Rev. 0

Section 1: Introduction

Introduction

Section 1: Introduction

This safety manual provides essential information necessary to design, install, verify and

maintain a Safety Instrumented Function (SIF) utilizing Emerson Actuator Series

GVO-CLP-SR/FS. This manual provides necessary requirements for meeting the IEC

61508:2010 (Sections 1 to 7) or IEC 61511 functional safety standards.

SIL Safety Manual

SM-025-GVO Rev. 0

November 2017

Section 2: Acronyms

Acronyms

Section 2: Acronyms

FMEDA: Failure Modes, Effects and Diagnostic Analysis

HFT: Hardware Fault Tolerance

(ref: 7.4.4 of IEC 61508-2:2010)

PFDAVG:Average Probability of dangerous Failure on Demand

(ref: 3.6.18 of IEC 61508-4:2010)

SFF: Safe Failure Fraction, property of a safety related element that is dened by

the ratio of the average failure rates of safe plus dangerous detected failures

and safe plus dangerous failures (ref: 3.6.15 of IEC 61508-4:2010)

SIF: Safety Instrumented Function, safety function with a specied safety

integrity level which is necessary to achieve functional safety and which

can be either a safety instrumented protection function or a safety

instrumented control function.

SIL: Safety Integrity Level, discrete level (one out of a possible four) for specifying

the safety integrity requirements of the safety functions to be

allocated to the E/E/PE safety related systems where Safety Integrity Level

4 has the highest level of safety integrity and Safety Integrity Level 1 has the

lowest. (ref: 3.5.8 of IEC 61508-4:2010)

SIS: Safety Instrumented System – Implementation of one or more Safety

Instrumented Functions. A SIS is composed of any combination of sensor(s),

logic solver(s), and nal element(s).

November 2017

SIL Safety Manual

SM-025-GVO Rev. 0

Section 3: Functional Specification

Functional Specification

Section 3: Functional Specication

The safety function performed by Emerson actuator series GVO-CLP-SR/FS is dened as

follows:

The actuator performs the safety function on demand if it delivers a full stroke driven by

the spring, moving the valve to the safe position (either closed or open depending upon

the valve to be actuated) when the system is de-energized.

The choice of the safety function to be implemented is responsibility of the system

integrator.

GVO-CLP-SR/FS actuator is intended to be part of the nal element subsystem as dened

per IEC 61508:2010. The achieved SIL level of the designed function must comply with the

project specication and must be submitted to the system integrator.

The nal control element subsystem needs to be sized properly to assure that its operating

time is equal or less than the time required to reach a safe state.

GVO-CLP-SR/FS actuator will move the valve to its safe state in equal or less than the

required SIF’s response time under the specied conditions.

SIL Safety Manual

SM-025-GVO Rev. 0

November 2017

Section 4: Product Description

Product Description

Section 4: Product Description

4.1 GVO-CLP-SR/FS pneumatic linear spring return

actuator general description

Emerson GVO-CLP-SR/FS low pressure pneumatic spring return linear actuator series is

engineered and is manufactured to provide fail safe operation for any linear application such

as wedge gate and through conduit gate valves, in On-Off and Modulating Heavy duty service;

simplicity, reliability and economy are at the top of the list of design parameters.

Supply pressure is maximum 12 bar-gauge, accepting air, nitrogen or sweet gas.

Supported standard ambient temperature ranges from –30°C to +100°C, special versions of

actuators are available to be used for applications outside this temperature range.

The actuator is composed of a pneumatic cylinder, a spring cartridge and a mounting pedestal

complete with a joint for the coupling to the valve stem of actuator output stem.

The valve is actuated in opening and in closing position by the actuator pneumatic cylinder in

one direction and by the spring unit in the other direction. The output thrust of spring unit can

be downward or upward according to valve operation requirements (spring to open, spring

to close, direct acting valve, reverse acting valve).

The spring return pack incorporates up to four springs, fully encapsulated in a factory welded

cartridge: this assures safety conditions to personnel and simplifies the assembly. The

linear stroke of the valve is adjustable by means of the external mechanical stop and by the

adjustment of the coupling of valve stem to actuator joint.

The actuator pedestal has a ange with threaded holes to x the actuator to the valve.

A general sectional view of the actuator is shown in Figure 1.

Emerson can supply different types of control systems, following customer’s requirements.

Figure 1 GVO-CLP-SR/FS Actuator Overview

November 2017

SIL Safety Manual

SM-025-GVO Rev. 0

Section 4: Product Description

Product Description

4.2 GVO-CLP-SR/FS working principle

Emerson GVO-CLP-SR/FS actuator working principle is simplied in the following Figure 2.

In the normal operating situation the operating uid (instrument air, nitrogen or sweet gas)

is supplied to the actuator’s open (close) chamber of the pneumatic cylinder: the cylinder

piston stroke causes the actuator operation and the consequent valve movement to the open

(close) operational position, and at the same time compresses the spring. Upon a demand,

the instrument air is discharged from the open (close) chamber of the cylinder: the actuator

performs the closing (opening) operation driven by the spring, and the valve moves from the

open (close) position to the close (open) position (safety-related position).

Figure 2 GVO-CLP-SR/FS actuator simplified working principle

PNEUMATIC CONNECTION

SIL Safety Manual

SM-025-GVO Rev. 0

November 2017

Section 5: Service Condition Limitations

Service Condition Limitations

Section 5: Service Condition Limitations

(limitation of use)

The designer of an SIF must check that the product is rated for use within the expected

application limits. The operating conditions limits strongly depend on the actuator type and

on its construction materials.

Operating pressure values are dened for each actuator.

Temperature limits are the following:

• Standard ambient temperature range: -30°C to +100°C

• Extended ambient temperature range: -60°C to +200°C (special versions)

Supply medium: instrument air, nitrogen or sweet gas (sour gas special version is available).

If GVO-CLP-SR/FS actuator is intended to be used outside the application limits or with

incompatible materials, the reliability data provided in the present document are invalid.

• The actual environmental conditions are included on the actuator nameplate

• The chose values are valid for the lifetime specied in Section 6.

• Manual override

Normally, the GVO-CLP-SR/FS actuators can be tted with one of the following types of

manual overrides:

• MHW Manual Hand-wheel mounted on the end ange of the pneumatic cylinder

• MHP Manual Hydraulic override including an additional hydraulic cylinder with

manual pump and distributor

With reference GVO-CLP-SR/FS actuator, the mechanical manual override can be done with

three conguration depending of the actuator size:

The use of a manual override is not recommended in a SIL classied application, as it results

in a bypass of the safety function.

In case the manual override is used, the following requirements must be fulllled, or the

Functional Safety Certication will become invalid:

1. The users authorized to operate on the actuator shall be skilled personnel;

2. The maximum duration of bypass shall be dened (responsibility of the nal user).

3. If necessary, compensatory measures to allow the safe operation of the process

shall be dened (responsibility of the nal user).

4. Before selecting remote operating mode control of actuator, the manual override

must be disengaged according to IOM Manual. The position selected

(remote/automatic control or local / manual control) can be achieved with a

specic technical solution that does not allow to reach an intermediate position

lever’s and avoids unintentional activation.

5. The engagement of the manual override shall be signalled, at least locally,

according to IOM Manual. As optional request from nal user, to determine if the

manual override is engaged, an electrical signal using contact switching can be

provided to communicate the status to the control room.

November 2017

SIL Safety Manual

SM-025-GVO Rev. 0

Section 5: Service Condition Limitations

Service Condition Limitations

Table 1.

MHW Manual Hand-wheel

MHP Manual Hydraulic

To ensure that the hand pump has been correctly disengaged after a manual override

operation, the following test shall be completed:

- restore the manual lever to remote position;

- verify the functionality performing a test from remote control (es. partial stroke test).

Andere Handbücher für Bettis GVO-C Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson Fisher 785C Bedienungsanleitung

Emerson

Emerson DIXELL XR60T Bedienungsanleitung

Emerson

Emerson FISHER 66 Bedienungsanleitung

Emerson

Emerson Hytork XL26 Gebrauchsanweisung

Emerson

Emerson Fisher 1078 Bedienungsanleitung

Emerson

Emerson Bettis TEC2 Bedienungsanleitung

Emerson

Emerson Vilter MicroVission Bedienungsanleitung

Emerson

Emerson uerdant VX Series Bedienungsanleitung

Emerson

Emerson MR105 Bedienungsanleitung

Emerson

Emerson Unidrive SPM Bedienungsanleitung

Emerson

Emerson Fisher 161 Series Bedienungsanleitung

Emerson

Emerson Bettis RGS F Series Bedienungsanleitung

Emerson

Emerson EIM 2000 Series Handbuch

Emerson

Emerson EC3-D72 Bedienungsanleitung

Emerson

Emerson FISHER CS200 Series Bedienungsanleitung

Emerson

Emerson A36 Handbuch

Emerson

Emerson Dixell XR60CH Verdrahtungsschema

Emerson

Emerson Dixell XR70CHC Verdrahtungsschema

Emerson

Emerson HVAC Drive H300 Bedienungsanleitung

Emerson

Emerson Dixell XR60CHC Verdrahtungsschema

Emerson

Emerson PaCSystems VersaMax Series Bedienungsanleitung

Emerson

Emerson KEYSTONE FIGURE 738 Handbuch

Emerson

Emerson Unidrive M400 Bedienungsanleitung

Emerson

Emerson FPCSK Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung