Emerson DIXELL XR60T Bedienungsanleitung

1569005010 XR30-60-70T QRG EN r1.2 2021.05.10 XR30-60-70T 1/2

FULL TOUCH –XR30-60-70T

Please put this label near the controller in order to keep

all information you need at your fingertips!

XR60T

XR70T

XR30T

SAFETY INFO

•This manual is part of the product and should be kept near the instrument for easy and quick reference.

•The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device.

•Dixell Srl reserves the right to change the composition of its products, even without notice, ensuring the same and unchanged functionality.

•In case of failure or faulty operation, contact the local distributor or “Dixell S.r.l.” with a detailed description of the fault.

•The instrument must not be opened.

•Check the application limits and the correct power supply voltage before proceeding.

•Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high

atmospheric humidity to avoid condensation

•Warning: disconnect the power supply and all other electrical connections before any kind of maintenance.

•Observe the maximum current value which can be applied to each relay (see Technical Data).

•Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining.

USER INTERFACE

SCREEN

APPEARANCE

SCREEN

APPEARANCE

Home

Info

Virtual

Keyboard

Programming

Mode

Parameter

Set Point Menu

SCREEN NAME

DESCRIPTION

Home

This screen shows temperature value, measurement unit and active alarms only. This is the first screen after power

on or after exit from other status.

Virtual Keyboard

This screen shows available functions. Activated function will blink when this screen is visualized.

Info

This screen shows activated functions and regulation outputs (compressor, ventilators)

Programming Mode

This screen enables the modification of the Set point or parameters.

Parameter Menu

These screens enable the modification of all parameter values.

Set Point Menu

This screen enables the modification of the Set Point value.

This screen is for creating the parameter label by swiping-up every single part of the label itself (first, second and third

char).

USER INTERACTION

HOME NAVIGATION

SET POINT TEMPERATURE

PROG MENU

ALL PARAMETER MENU

H-SWIPE

TAP & HOLD

ANYWHERE

TAP & HOLD

PRG

H-SWIPE

TAP & HOLD

SET

TAP & HOLD

PRG

H-SWIPE

V-SWIPE

H-SWIPE

TAP & HOLD

PRG

GESTURE

HOW-TO

DESCRIPTION

ONE TAP

Press a specific area of the screen

with a finger for 1 sec

Switch ON / Switch OFF: when in Virtual Keyboard, use this to turn on/off a

specific function. When in Programming mode, use this to select a parameter or a

parameter value.

TAP and

HOLD

Press any place of the screen with a

finger for 3 sec

Enter / Save: use this to enter Programming mode or Parameter menu and to

save modifications. When in Virtual Keyboard, use this on the “ONOFF” to switch

OFF and ON the device.

1569005010 XR30-60-70T QRG EN r1.2 2021.05.10 XR30-60-70T 2/2

H-SWIPE

Drag a finger across the screen, from

left to right or from right to left

Browse: use horizontal swipe (right to left or left to right) to browse through

HOME, Virtual Keyboard and Info View. When in programming mode: use

horizontal swipe to browse through parameter menu.

V-SWIPE

Drag a finger across the screen, from

top to bottom or from bottom to top

(overlapping only one of the digits)

Modify: use vertical swipe (from top to bottom or bottom to top) to change a

parameter value.

PROGRAMMING MENU

TAP and HOLD 3 sec anywhere

TAP and HOLD “PRG”

H-SWIPE to browse

(…)

and icons are blinking

TAP and HOLD “PRG”

V-SWIPE to modify

TAP and HOLD “PRG” to save and exit

TECHNICAL SPECIFICATIONS

FEATURES

DESCRIPTION

Housing

Self-extinguishing PC

Dimensions

Front fascia 38x80 mm; case depth 81mm

Mounting device

Panel, 71x29mm panel cut-out

Degree of Protection

NEMA –UL 50e

Indoor use only, Type 1 enclosure

IP-IEC/EN 60529

Front panel: IP66

Rear Housing: IP00

Power Supply

230Vac 10%, 50/60Hz; 110Vac 10%, 50/60Hz; 100 to 240VAC10%, 50/60Hz

Overvoltage Category

Rated Power

12VAC: 3VA; 110VAC: 4VA; 230VAC: 4VA; 100-240VAC: 3VA

Rated Impulse Voltage

2500V

Display

White display, LED type, 3 digits with decimal point and multi-function icons

Buzzer

Internal, always present

Software Class

Terminal blocks / Terminal

Connections

Plug-in or screw terminal block, wire section between 0,5 and 2,5 mm2

Max tightening force: 0.3 N/m for 3,5mm pitch, 0.4 N/m for 5,0mm pitch

Data Storing

Real Time Clock: Data maintenance up to 6 months with lithium battery. Other parameters: internal flash.

Type of Action

1.B

FEATURES

DESCRIPTION

Pollution Degree

2, non-condensing humidity

Ambient Operating

Temperature and Humidity

IEC/EN

0T60°C; 20-85 rH% (non-condensing humidity)

UL-CAN/CSA

-20T60°C; 20-85 rH% (non-condensing humidity)

Shipping and storage

temperature

-40T85°C; 20-85 rH% (non-condensing humidity)

Resistance to Heat

UL 94 V-0

Measurement range

NTC: -40T110°C, resolution 0.1°C or 1°C (selectable); PT1000: -100T150°C, resolution 0.1°C or 1°C

(selectable); PTC: -50T150°C, resolution 0.1°C or 1°C (selectable)

Accuracy

±1% compared to the full scale

Inputs

Up to 4 NTC, PTC or PT1000 (configurable); Up to 2 voltage free contacts

Relay Outputs

Nominal

IEC

oA1

SPST 16A,

250Vac

Resistive load 12A (NO), 230Vac, 50K cycles

Motor load 240Vac (NO), 10FLA/60LRA, 30K cycles

Pilot Duty B300 (NO), 6K cycles

10(4)A (NO), 230Vac, 100K

cycles

oA2

SPDT 8A,

250Vac

Resistive load 10A (NO), 120/240Vac, 30K cycles

Motor load ½ HP (NO), 240Vac, 30K cycles

Motor load ¼ HP (NO), 120Vac, 30K cycles

Pilot duty B300 (NO), 30K cycles

8(3)A (NO), 230Vac, 50K

cycles

oA3

(*)

SPST 5A,

250Vac

Resistive load 5A, 120/240Vac, 50K cycles

Motor load 240Vac, 1.9FLA/11.4LRA, 30K cycles

Pilot Duty B300, 30K cycles

5(1)A, 230Vac, 50K cycles

oA4

(**)

SPST 8A,

250Vac

Resistive load 10A (NO), 120/240Vac, 30K cycles

Motor load ½ HP (NO), 240Vac, 30K cycles

Motor load ¼ HP (NO), 120Vac, 30K cycles

Pilot duty B300 (NO), 30K cycles

8(3)A (NO), 230Vac, 50K

cycles

Maximum ampacity on common

terminal “Line” (for oAx)

16A

I/O port

HOT-KEY: MAX voltage allowed is 5 VDC. DO NOT CONNECT ANY EXTERNAL POWER SUPPLY.

Purpose of control

Operating control

Construction of control

Incorporated control, intended to be used in Class I or Class II equipment

Approvals

R290/R600a: relays tested according to IEC EN60079:0 and IEC EN60079:15

IEC/EN 60730-1; IEC/EN 60730-2-9

UL 60730-1; UL 60730-2-9

CAN/CSA E60730-1; CAN/CSA E60730-2-9

(*) XR60T and XR70T only

(**) XR70T only

Dieses Handbuch passt für folgende Modelle

Andere Emerson Controller Handbücher

Emerson

Emerson DIXELL XR77CHC Bedienungsanleitung

Emerson

Emerson Copeland EV2 Series Benutzerhandbuch

Emerson

Emerson Fisher 2052 Bedienungsanleitung

Emerson

Emerson NZ Series Bedienungsanleitung

Emerson

Emerson unidrive m200 Bedienungsanleitung

Emerson

Emerson FISHER SR8 Bedienungsanleitung

Emerson

Emerson Sempell series Bedienungsanleitung

Emerson

Emerson Fisher L2e Bedienungsanleitung

Emerson

Emerson PACSystems RX3i DNP3 Bedienungsanleitung

Emerson

Emerson Fisher 92S Bedienungsanleitung

Emerson

Emerson Fisher 67D Series Bedienungsanleitung

Emerson

Emerson dixell XW90LT Verdrahtungsschema

Emerson

Emerson CASH VALVE B Series Handbuch

Emerson

Emerson digitax st series Bedienungsanleitung

Emerson

Emerson PNC001-A Series Bedienungsanleitung

Emerson

Emerson Fisher 1305 Series Bedienungsanleitung

Emerson

Emerson Digitax ST Bedienungsanleitung

Emerson

Emerson Bettis 2000 Series E796 M2CP Handbuch

Emerson

Emerson Fisher Accu-Pressure Y693 Bedienungsanleitung

Emerson

Emerson EC3-D72 Bedienungsanleitung

Emerson

Emerson E2 Bedienungsanleitung

Emerson

Emerson PMAC II Solo Bedienungsanleitung

Emerson

Emerson unidrive m Bedienungsanleitung

Emerson

Emerson fisher 1008 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung