Emerson EIM HQ Series Bedienungsanleitung
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
May 2020
EIM HQ Series Quarter-Turn Electric Actuator
Models HQ-008/015/020/030/050/060/080/120/200/300/
Manual HQ-400-1005
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
This page intentionally left blank
Notes
May 2020
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
i
Table of Contents
Section 1: General
1.1 Pre-Installation Inspection ............................................................................ 1
Section 2: Actuator Mounting
Actuator Mounting ................................................................................................. 2
Section 3: External Construction
External Construction ............................................................................................. 3
Section 4: Wiring Diagrams
Wiring Diagrams..................................................................................................... 4
Section 5: Power Requirements
Power Requirements............................................................................................... 6
Section 6: Duty Cycle
Duty Cycle .............................................................................................................. 7
Section 7: Handwheel Declutch / Manual Override
Handwheel Declutch / Manual Override .................................................................. 8
Section 8: Mechanical Travel Stop Adjustment
Mechanical Travel Stop Adjustment......................................................................... 9
Section 9: Electrical Connection
Electrical Connection............................................................................................ 10
Section 10: Limit Switch Setting Instructions
Limit Switch Setting Instructions........................................................................... 11
Table of Contents
May 2020
Table of Contents
ii
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
Section 11: Torque Switch Adjustment
Torque Switch Adjustment.................................................................................... 12
Section 12: Reverse Acting (Counterclockwise to Close)
Reverse Acting (Counterclockwise to Close).......................................................... 13
Section 13: Lubrication
Lubrication............................................................................................................ 14
Section 14: MDPI (Mechanical Dial Position Indicator) Settings
MDPI (Mechanical Dial Position Indicator) Settings................................................ 15
Section 15: Maintenance
Maintenance......................................................................................................... 16
Section 16: Storage
Storage................................................................................................................. 17
Section 17: Mounting Base Detail
Mounting Base Detail............................................................................................ 18
Section 18: Drive Bushing Details
Drive Bushing Details ............................................................................................ 19
Section 19: Troubleshooting
Troubleshooting ................................................................................................... 20
Section 20: Product Features and Specications
Product Features and Specications...................................................................... 21
Table of Contents
Table of Contents
May 2020
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
May 2020
1
Section 1: General
HQ Series electric actuators are design to provide reliable and efcient operation of 90°
quarter-turn valves, dampers, etc.
! WARNING
Use caution when working in, with, or around valves and actuators. High pressures, forces,
voltages and ammable media can be present.
! WARNING
Failure to follow instructions for proper electrical wiring, storage, set-up and maintenance
may cause serious injury, damage equipment, or void warranty.
1.1 Pre-Installation Inspection
Verify the actuator nameplate to insure correct model number, torque, operating speed,
voltage and enclosure type before installation or use. It is important to verify that the
output torque of the actuator is appropriate for the torque requirements of the valve and
that the actuator duty cycle is appropriate of the intended application.
Section 1: General
General
May 2020
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
2
Section 2: Actuator Mounting
Do not lift the actuator by the handwheel.
The actuator may be mounted in any position. The HQ-Series actuators are supplied
with a female drive output, ISO5211. Bolt patterns are provided for actuator mounting.
The actuator drive bush is removable for ease of machining.
It is mandatory that the actuator be rmly secured to a sturdy mounting bracket or directly
mounted to the valve’s ISO mounting pad. High tensile bolts or studs with spring locking
washers must be used. The valve output shaft must be in line with the actuator output
drive to avoid side-loading the shaft. To prevent backlash, no exibility in the mounting
bracket or mounting should be allowed.
Actuator Mounting
Section 2: Actuator Mounting
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
May 2020
3
Section 3: External Construction
Figure 1 HQ-008 – HQ-120
Figure 2 HQ-200 – HQ-300
Conduit Entries
MDPI
Cover Bolts
Drive Bushing
Declutch
Lever
Cover
Handwheel
Travel Stop Bolts
Drive Bushing
Travel Stop Bolts
Gearbox
MDPI
Section 3: External Construction
External Construction
May 2020
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
4
OT OC
Section 4: Wiring Diagrams
Figure 3 AC Single Phase Power Model HQ 015 - 300
POWER
(V)
INCOMING
AC 1PH
LIVE
NEUTRAL
OVER
TORQUE
LAMP
CLOSE
LAMP
OPEN
LAMP OPEN STOP CLOSE
AUX. CONTACT
2 EXTRA SWITCHES
MAX. 250 V AC 16 A
SUGGESTED CUSTOMERS WIRING
ACTUATORS WIRING
CONDENSER
BASE
EARTH
Section 4: Wiring Diagrams
Wiring Diagrams
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
May 2020
5
Figure 4 AC 3-Phrase Power Model
Wiring Diagrams
Section 4: Wiring Diagrams
May 2020
Installation, Operation and Maintenance Manual
VCIOM-15204-EN Rev. 1
6
Section 5: Power Requirements
Consult the nameplate of the actuator for duty cycle and current draw information.
Section 5: Power Requirements
Power Requirements
Andere Handbücher für EIM HQ Series
1
Dieses Handbuch passt für folgende Modelle
10
Inhaltsverzeichnis
Andere Emerson Controller Handbücher
Emerson
Emerson E2 Bedienungsanleitung
Emerson
Emerson Dixell XR60C Verdrahtungsschema
Emerson
Emerson Alco Controls EC3 Series Bedienungsanleitung
Emerson
Emerson Dixell XR44CX Verdrahtungsschema
Emerson
Emerson FISHER 627F Bedienungsanleitung
Emerson
Emerson fisher 1008 Bedienungsanleitung
Emerson
Emerson Bettis RP4AF Bedienungsanleitung
Emerson
Emerson Dixell XT130C Verdrahtungsschema
Emerson
Emerson Dixell XR60CH Verdrahtungsschema
Emerson
Emerson Dixell WING XW563L Verdrahtungsschema
Emerson
Emerson REGAL 3F Bedienungsanleitung
Emerson
Emerson Bettis G Series Bedienungsanleitung
Emerson
Emerson TESCOM Einrichtungshandbuch
Emerson
Emerson S402Y Bedienungsanleitung
Emerson
Emerson Dixell XM660K Verdrahtungsschema
Emerson
Emerson Lumity E3 Bedienungsanleitung
Emerson
Emerson FISHER CS200 Series Bedienungsanleitung
Emerson
Emerson SH Series Bedienungsanleitung
Emerson
Emerson Fisher FIELDVUE DVC6200 SIS Bedienungsanleitung
Emerson
Emerson Bettis CBB Series Montageanleitung
