Emerson Fisher easy-Drive 200L Bedienungsanleitung

www.Fisher.com

Fisher™easy-Drive™200L Quick Start Guide

Mounting and travel configuration for your Fisher easy-Drive 200L actuator.

Before You Begin

Do not install, operate, or maintain a 200L actuator without being fully trained and qualified in valve,

actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property

damage, it is important to carefully read, understand, and follow all the contents of this quick start

guide, including all safety cautions and warnings. Refer to the Fisher easy-Drive 200L Instruction Manual

(D104331X012) for product specifications, custom setup information, maintenance procedures, and

installation in hazardous locations. If you have any questions about these instructions, contact your

Emerson sales office before proceeding.

WARNING

To avoid personal injury or property damage, keep hands and tools out of the actuator stem travel path. The actuator stem

will move during calibration and positioning steps.

Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personal

injury.

Note

Refer to easy-Drive 200L Instruction Manual (D104331X012) for wiring, Modbus setup and connecting the Configurator to an

easy-Drive actuator as this will be needed to configure and calibrate the 200L.

Quick Start Guide

D104725X012

easy-Drive 200L

March 2022

Quick Start Guide

D104725X012

easy-Drive 200L

March 2022

Ensure Actuator Stem is in the Proper Position Prior

to Mounting and Coupling

Your 200L actuator has internal hard stops to limit maximum travel within the actuator. A new actuator will be shipped

from the factory at 6% off the lower internal hard stop, which is the recommended mounting position.

Note

If you are mounting a new actuator that has never been positioned and is still in its recommended mounting position of 6% of

maximum travel, you can begin at step 5.

To set the stand-alone 200L actuator to the recommended mounting position of 6% of maximum travel, follow steps

1-4:

Step 1. Ensure use of a stand-alone 200L

(must be actuator only, no valve body).

Step 2. Using the Fisher easy-Drive Configurator,

select the “System” tab and then

“Advanced Settings.” Select the valve

type “Stop-to-Stop” from the drop-down

options and click “Apply.”

Step 3. Perform Span Calibration from

Calibration tab. Step 4. Position actuator to 6% travel.

X1520-1

Note

Stop-to-Stop is used for positioning the actuator to 6% off the lower travel stop.

Select proper valve type and travel after mounting the 200L to the valve body.

Quick Start Guide

D104725X012

easy-Drive 200L

March 2022

Mount the Actuator to the Valve Body and Couple the Stems

Note

User supplied mounting bracket and stem coupler will be needed to complete this procedure.

25.75 MAX

Inch

10-15

0.39-0.59

1.013 MAX

2.48

9.61

244

Step 5. Supply a method of supporting the

weight of the valve and actuator during

assembly.

Step 6. Push the valve stem down away from the

actuator to the valves closed position for

push down to close valves.

Step 7. Mount the to the mounting bracket

supplied by the user. Tighten the actuator

locknut to 205 N•m (151lb•ft).

Step 8. Lift or hoist the actuator and mounting

bracket onto the valve and mate the

mounting bracket securely to the valve

following the valve manufacturer's

instructions.

Step 9. Make the stem connection between the

actuator and valve stems. When installing

the user-supplied stem connector, be sure

the actuator stem threads engage the

threads of the stem connector by a

distance equal to or greater than the

diameter of the actuator stem.

GE94736

WRENCH

FLATS

LOCKNUT

3.27EXTENDED

RETRACTED

1/2-20UNF-2A

6.3

0.25

27.3

1.07

1.969

Refer to the easy-Drive 200L bulletin (D104361X012) for complete mounting specifications.

Select Proper Valve Type

Step 10.Refer to valve manufacturer

documentation to determine maximum

valve travel. (Manufacturer specifications

may vary.)

Step 11.In the Configurator, navigate to the

Calibration tab.

Step 12.Click on the “Valve Type” and select the

appropriate value that matches desired travel

of the valve body for your application and is

within manufacturer valve travel limits. Then

click “Apply” to save the selection.

Note

Stop-to-Stop valve type selection should be avoided unless

the valve is specifically designed with its own internal up and

down hard stops within the valve body. Fixed travel settings

are recommended and will set the travel from the valve seat

(push down to close) up to a pre-defined amount of travel,

e.g. '0.75” Fixed' setting, will set the full range of travel at 19

mm (0.75 inches) from the seat.

Quick Start Guide

D104725X012

easy-Drive 200L

March 2022

Calibrate Travel of the Actuator to the Valve Assembly

Step 13.Ensure the process and valve are in a safe

state – the valve will move during the

calibration steps.

Step 14.Navigate to the Calibration tab of the

Configurator

Step 15.Press the “Calibrate Span” button to

initiate the span calibration. The software

will show a progress bar during the

calibration and display “Valve Span

Calibrated” when complete.

Note

If actuator cannot achieve desired travel, review steps 5-12 to ensure all steps were followed, validate proper Configurator

selections were made, and confirm the stems were properly coupled.

Step 16.Verify valve is closed when commanded

to 0%.

Step 17.Verify full desired travel is achieved when

commanded to 100% by confirming

“Actual Position” in the Configurator is

100%.

The valve/actuator assembly is now ready to be put into operation. If the 200L is not operating properly contact your

Emerson sales office.

Emerson Automation Solutions

Marshalltown, Iowa 50158 USA

Sorocaba, 18087 Brazil

Cernay, 68700 France

Dubai, United Arab Emirates

Singapore 128461 Singapore

www.Fisher.com

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not

to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are

governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such

products at any time without notice.

Fisher and easy-Drive are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson

Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their

respective owners.

Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance

of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.

Andere Handbücher für Fisher easy-Drive 200L

Andere Emerson Controller Handbücher

Emerson

Emerson FISHER T208VR Series Bedienungsanleitung

Emerson

Emerson Fisher 657C Bedienungsanleitung

Emerson

Emerson Level-Trol 2500 Series Bedienungsanleitung

Emerson

Emerson dixell XC10CX Verdrahtungsschema

Emerson

Emerson COPELAND XC PRO Betriebsanleitung

Emerson

Emerson dixell WING XW260K Verdrahtungsschema

Emerson

Emerson ControlWave Bedienungsanleitung

Emerson

Emerson EC3-D72 Bedienungsanleitung

Emerson

Emerson Motorola MVME162 Bedienungsanleitung

Emerson

Emerson Fisher L2e Konfigurationshandbuch

Emerson

Emerson Fisher FIELDVUE DVC6005 Series Konfigurationshandbuch

Emerson

Emerson Dixell XR60CH Verdrahtungsschema

Emerson

Emerson Dixell XRB Verdrahtungsschema

Emerson

Emerson iPro.Genius Kurzanleitung

Emerson

Emerson Fisher 67C Series Bedienungsanleitung

Emerson

Emerson Vilter MicroVission Bedienungsanleitung

Emerson

Emerson Fisher Y692VB Series Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC7K Bedienungsanleitung

Emerson

Emerson AXIMA 2000 Bedienungsanleitung

Emerson

Emerson Fisher LR125 Series Bedienungsanleitung

Emerson

Emerson Dixell IEV12D Verdrahtungsschema

Emerson

Emerson Dixell XM670K Verdrahtungsschema

Emerson

Emerson Fisher SR5 Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DLC3020f Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung