Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Quick Start Guide

00825-0200-4420, Rev FB

January 2015

Smart Wireless Gateway 1420

00825-0200-4420_RevFB.fm Page 1 Friday, January 16, 2015 1:56 PM

January 2015

Quick Start Guide

NOTICE

This guide provides basic guidelines for the Smart Wireless Gateway. It does not provide

instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Smart

Wireless Gateway Reference Manual (document number 00809-0200-4420) for more

information and instructions. The manual and this Quick Start Guide are available

electronically on www.emersonprocess.com.

Explosions could result in death or serious injury.

Installation of this device in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please review

the Product Certifications section for any restrictions associated with a safe installation.

Avoid contact with the leads and terminals. High voltage that may be present on leads can

cause electrical shock. This device complies with Part 15 of the FCC Rules. Operation is subject

to the following conditions. This device may not cause harmful interference. This device must

accept any interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 20 cm from

all persons.

Contents

Wireless considerations . . . . . . . . . . . . . . . . 3

General considerations . . . . . . . . . . . . . . . . . 4

Initial connection and configuration . . . . 5

Physical installation . . . . . . . . . . . . . . . . . . .10

Connect to the host system . . . . . . . . . . .15

Software installation (optional) . . . . . . . .16

Verify operations . . . . . . . . . . . . . . . . . . . . . .17

Product Certifications . . . . . . . . . . . . . . . . .18

00825-0200-4420_RevFB.fm Page 2 Friday, January 16, 2015 1:56 PM

Quick Start Guide

January 2015

Wireless considerations

Power up sequence

The Smart Wireless Gateway (Gateway) should be installed and functioning

properly before power modules are installed in any wireless field devices. Wireless

field devices should also be powered up in order of proximity from the Smart

Wireless Gateway beginning with the closest. This will result in a simpler and

faster network installation.

Antenna position

The antenna should be positioned vertically, and be approximately 3 ft. (1 m)

from large structures or buildings to allow for clear communication to other

devices.

Mounting height

For optimal wireless coverage, the Gateway or remote antenna is ideally mounted

15-25 ft. (4,6 - 7,6 m) above ground or 6 ft. (2 m) above obstructions or major

infrastructure.

Gateway redundancy

If the wireless Gateway was ordered with redundancy (Gateway Redundancy code

RD), refer to Appendix D in the Smart Wireless Gateway Reference Manual

(document number 00809-0200-4420) for additional installation instructions.

00825-0200-4420_RevFB.fm Page 3 Friday, January 16, 2015 1:56 PM

January 2015

Quick Start Guide

General considerations

PC requirements

Operating system (optional software only)

Microsoft®Windows™XP Professional, Service Pack 3

Windows Server 2003 Service Pack 2

Windows Server 2003 R2 Service Pack 2

Windows Server 2008 (Standard Edition), Service Pack 2

Windows Server 2008 R2 Standard Edition, Service Pack 1

Windows 7 Professional, Service Pack 1

Windows 7 Enterprise, Service Pack 1

Applications

Internet Explorer®6.0 or higher

Mozilla Firefox®1.5 or higher

.Net Framework 2.0 (for OPC proxy only)

Hard disk space

AMS®Wireless Configurator: 1.5 GB

Gateway Setup CD: 250 MB

00825-0200-4420_RevFB.fm Page 4 Friday, January 16, 2015 1:56 PM

Quick Start Guide

January 2015

Step 1: Initial connection and configuration

DeltaV™ready

If the Gateway was ordered DeltaV Ready (Data Protocols Code 5), then Step 1:

Initial connection and configuration is not required. Proceed to Step 2: Physical

installation, and connect the Gateway to a DeltaV 10.3 or newer control network.

Initial connection and configuration

To configure the Smart Wireless Gateway, a local connection between a

PC/laptop and the Gateway needs to be established.

Powering the gateway

Bench top power will be needed to power the Gateway by wiring a 24 VDC

(nominal) power source, with at least 250 mA, to the power terminals.

Figure 1. Gateway Terminal Block Diagram

Establishing a connection

Note

For information on connecting a Windows 7 PC, see the technical note (document number

00840-0900-4420).

1. Connect the PC/laptop to the Ethernet 1 (Primary) receptacle on the Gateway.

24 VDC

(nominal)

Power Input

Serial

Modbus

Not

Case

(Covered)

Ethernet 2

with Power Ethernet 2 Ethernet 1

(Secondary) (Primary)

00825-0200-4420_RevFB.fm Page 5 Friday, January 16, 2015 1:56 PM

January 2015

Quick Start Guide

Figure 2. Gateway PC/Laptop Connection Illustration

A. PC/laptop

B. Ethernet 1 Receptacle

2. To establish the PC/laptop settings, navigate to Start>Settings>Network

Connections.

a. Select Local Area Connection.

b. Right click to select Properties.

c. Select Internet Protocol (TCP/IP), then select the Properties button.

Note

If the PC/laptop is from another network, record the current IP address and other settings so the

PC/laptop can be returned to the original network after the Gateway has been configured.

Do not connect to the Ethernet 2 with power (covered) port. This port supplies power and

could damage the PC/laptop.

+ +

-A B S S

24V DC24V DC

PowerInputPowerInput ModbusModbus Not UsedNot Used Not UsedNot Used

Not UsedNot Used Not UsedNot Used

CaseCase

POEPOE P2P2 P1P1

00825-0200-4420_RevFB.fm Page 6 Friday, January 16, 2015 1:56 PM

Quick Start Guide

January 2015

d. Select the Use the following IP address button.

e. In the IP address field, enter 192.168.1.12.

f. In the Subnet mask field, enter 255.255.255.0.

g. In the Internet Protocol (TCP/IP) Properties window, select OK.

h. In the Local Area Connection Properties window, select OK.

Note

Connecting to the Gateway's secondary Ethernet port requires different network settings. Refer to

Table 1 for additional network settings.

Table 1. Default IP Addresses

Gateway PC/laptop

Ethernet 1 192.168.1.10 192.168.1.12

Ethernet 2 192.168.2.10 192.168.2.12

Ethernet 1 (DeltaV Ready) 10.5.255.254 10.5.255.200

Ethernet 2 (DeltaV Ready) 10.9.255.254 10.9.255.200

Table 2. Subnet Settings

Subnet mask

Default 255.255.255.0

DeltaV 255.254.0.0

00825-0200-4420_RevFB.fm Page 7 Friday, January 16, 2015 1:56 PM

January 2015

Quick Start Guide

3. Disable proxies.

a. Open a standard web browser (Internet Explorer, Mozilla Firefox, or

other).

b. Navigate to Tools>Internet Options>Connections>LAN Settings.

c. Uncheck the box under Proxy Server.

Configure the Smart Wireless Gateway

To complete initial configuration for the gateway:

1. Access the default web page for the Gateway at https://192.168.1.10.

a. In the User name field, enter admin.

b. In the Password field, enter default.

00825-0200-4420_RevFB.fm Page 8 Friday, January 16, 2015 1:56 PM

Quick Start Guide

January 2015

Figure 3. Gateway Log In Screen

2. Navigate to System Settings>Gateway>Ethernet Communication to enter

the Network Settings.

a. Configure a static IP Address or set for DHCP and enter a Hostname.

b. Restart application at System Settings>Gateway>Backup And

Restore>Restart App.

3. Disconnect the power and Ethernet from the Gateway.

00825-0200-4420_RevFB.fm Page 9 Friday, January 16, 2015 1:56 PM

January 2015

Quick Start Guide

Step 2: Physical installation

Pipe mount

Tools needed:

2-in. (51 mm) mounting pipe or mast

Two 5/16-in. (7,9 mm) u-bolts supplied with Gateway

1/2-in. socket-head wrench

For installing the Gateway in a pipe mount:

1. Insert one u-bolt around the pipe, through the top mounting holes of the

Gateway enclosure, and through the washer plate.

2. Use a 1/2-in. socket-head wrench to fasten the nuts to the u-bolt.

3. Repeat for the second u-bolt and lower mounting holes.

Best practice

If the Gateway was ordered with Output Code 2, run a secondary Ethernet cable

when installing cable conduit from the Gateway to a convenient indoor location

to simplify future configuration changes.

00825-0200-4420_RevFB.fm Page 10 Friday, January 16, 2015 1:56 PM

Andere Handbücher für Smart Wireless Gateway 1420

Inhaltsverzeichnis

Andere Emerson Tor Handbücher

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway Bedienungsanleitung

Emerson

Emerson Copeland PerformanceAlert Bedienungsanleitung

Emerson

Emerson CH Breaker Gateway Bedienungsanleitung

Emerson

Emerson 1552WU Bedienungsanleitung

Emerson

Emerson 1410S Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson 1410S Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1410 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway Bedienungsanleitung

Emerson

Emerson 1410 D Bedienungsanleitung

Emerson

Emerson 1410S Bedienungsanleitung

Emerson

Emerson ATCA-8310 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1420 Bedienungsanleitung

Emerson

Emerson 1410S Bedienungsanleitung

Emerson

Emerson Smart Wireless Gateway 1410 Bedienungsanleitung

Emerson

Emerson PACSystems RX3i Bedienungsanleitung

Emerson

Emerson 1410S Bedienungsanleitung

Emerson

Emerson 1410H Bedienungsanleitung

Emerson

Emerson 1410H Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung