Emerson USB Fieldbus Interface Bedienungsanleitung
User's Manual
AW7060MNL, Rev 3
January 2019
USB Fieldbus Interface
User's Manual
Copyright
© Emerson, 2019. All rights reserved. Printed in the USA.
Trademarks
The Emerson logo is a trademark and service mark of Emerson Electric Co.
AMS is a mark of one of the Emerson group of companies.
FOUNDATION™ is a mark of the FieldComm Group of Austin, Texas, USA.
Microsoft and Windows are registered trademarks of the Microsoft Corporation in the United
States and/or other countries.
PACTware is a trademark of PACTware Consortium e.V.
All other marks are property of their respective owners.
Contents
Introduction ................................................. 3
USB Fieldbus Interface .................................. 5
Software installation and device setup ........10
USB Fieldbus Interface Configuration
utility .......................................................... 17
Using with AMS Device Manager .................25
Using with an FDT Frame Application ..........33
Troubleshooting ......................................... 44
Approvals and certifications ........................48
Specifications ............................................. 49
Waste disposal ............................................50
Remove pre-release driver versions on a
Windows 7 or 10 operating system .............51
User's Manual January 2019
2
1 Introduction
This manual guides you in using the USB Fieldbus Interface to power and/or
configure fieldbus devices. Included here are basic setup, configuration, and
troubleshooting information, as well as guidelines on how to use the
interface with AMS Device Manager and with a third-party FDT Frame
Application.
This USB Fieldbus Interface User's Manual contains the following information:
•Chapter 1: Introduction – contains safety messages and information
about this manual.
•Chapter 2: USB Fieldbus Interface – contains information about the
interface, its parts, usage, and features.
•Chapter 3: Software installation and device setup – contains system
requirements, software installation instructions, and device setup
information.
•Chapter 4: USB Fieldbus Interface Configuration utility – contains
information on how to use the utility to power, commission, and/or
configure some parameters of fieldbus devices, including device address
and tag.
•Chapter 5: Using with AMS Device Manager – contains setup
information and instructions in using the interface with AMS Device
Manager to configure fieldbus devices.
•Chapter 6: Using with an FDT Frame Application – contains setup
information and instructions in using the interface with an FDT Frame
Application to configure fieldbus devices.
•Chapter 7: Troubleshooting – contains solutions to the most common
operating problems.
•Appendix A: Approvals and certifications – contains certifications and
approval information.
•Appendix B: Specifications – contains specifications such as operating
temperature, software, electrical information, and environmental
considerations.
•Appendix C: Waste disposal – contains disposal guidelines.
•Appendix D: Remove pre-release driver versions on a Windows 7 or
10 operating system – contains instructions on how to remove previous
driver versions.
January 2019 User's Manual
3
1.1 Safety message
WARNING!
Do not connect the USB Fieldbus Interface to a live segment (with an active
DCS Host and power supply attached) if the power indicator light on the
interface is amber in color. Doing so can disrupt communications and may
compromise automation safety.
User's Manual January 2019
4
2 USB Fieldbus Interface
Topics covered in this chapter:
•Overview
•Parts and function
•Power modes
2.1 Overview
The USB Fieldbus Interface enables two-way communication between a
computer and fieldbus devices. Its primary function is to allow the setup,
configuration, monitoring, and troubleshooting of fieldbus devices at any
valid FF address through a computer.
The interface is fully compatible with all FOUNDATION fieldbus (FF) devices
and is always configured as a "visitor."
It is particularly useful in these plant scenarios:
•Workbench setup and troubleshooting of fieldbus devices
•With a laptop in the field to configure, commission, decommission, set
device address, or troubleshoot fieldbus devices
The USB Fieldbus Interface comes with a USB cable, lead set, user's manual*,
and installation CD/DVD*. The user's manual and installation CD/DVD are not
included in the illustration.
January 2019 User's Manual
5
Box ContentsFigure 2-1:
User's Manual January 2019
6
2.2 Parts and function
USB Fieldbus InterfaceFigure 2-2:
1 Field connection indicator light (*) Indicates the fieldbus device connection status
2 Power indicator light (*) Indicates the power mode of the interface
3 USB port Enables USB connection
4 Fieldbus device connection socket Enables fieldbus device or segment connection
(*) See the Indicator light scenarios table.
January 2019 User's Manual
7
Indicator light scenariosTable 2-1:
Power
indicator
light
Field
connection
indicator light
Scenarios
Normal scenarios
Green Green The USB Fieldbus Interface is connected to an externally
powered segment and is able to communicate.
Amber Green The USB Fieldbus Interface is providing power to a fieldbus
segment and is able to communicate.
Other scenarios
Off Off
The USB Fieldbus Interface is not connected to a powered
computer.
-OR-
The USB Fieldbus Interface is connected to a computer but
the computer power is off.
-OR-
The USB FF HSE Server is not running on the connected
computer.
Green Off
The USB Fieldbus Interface is not connected to a powered
segment.
-OR-
The USB Fieldbus Interface is connected to a powered
segment with the wrong polarity.
Off Green The USB Fieldbus Interface is connected normally to a
powered segment but the USB FF HSE Server is not running.
Amber Red The USB Fieldbus Interface is providing power but a short
circuit has been detected on the field connection.
Amber Off
The USB Fieldbus Interface is providing power and
connected to an already powered fieldbus segment with
reverse polarity.
Amber Amber
The USB Fieldbus Interface is providing power to a fieldbus
segment and the load on that segment has exceeded its
limit.
User's Manual January 2019
8
2.3 Power modes
The USB Fieldbus Interface has two power modes:
•Mode 1 - The interface does not supply power to the connected fieldbus
device or segment. The fieldbus device or segment is powered by an
external source.
Mode 1 is the default.
•Mode 2 - The interface powers the connected fieldbus device or segment
and no external power is needed.
In Mode 2, it can provide current of up to 85 mA (typically sufficient for
three or four fieldbus devices on the same segment).
You can configure Mode 2 using the USB Fieldbus Interface Configuration
utility. For more information, see Section 4.3.
WARNING!
Choose only one power mode. Never attempt to use two power sources at
the same time. Doing so can disrupt communications and may compromise
automation safety.
January 2019 User's Manual
9
3 Software installation and device setup
Topics covered in this chapter:
•System requirements
•Install the USB Fieldbus Interface Configuration utility
•Install the Communication DTM software
•Install the Emerson DTM Library
•Setup and connection
•Connect to a live fieldbus segment
Perform software installation and device setup in the following order:
1. Install the USB Fieldbus Interface Configuration utility.
This allows you to configure the USB Fieldbus Interface and connected
fieldbus devices.
2. Install the Communication DTM software.
This enables DTM support for connected fieldbus devices.
3. Install the Emerson DTM Library.
This allows you to use DTMs associated with Emerson devices through an
FDT Frame Application.
Note
Device DTMs are usually acquired from device suppliers. Contact your
device supplier if you have a non-Emerson device and install the
appropriate third-party DTM library.
4. Set up and configure connected fieldbus devices.
3.1 System requirements
Supported operating systems
Windows 7 (32- or 64-bit)
Windows 10
Hard disk space
500MB or more
Hardware
User's Manual January 2019
10
Andere Handbücher für USB Fieldbus Interface
2
Inhaltsverzeichnis
Andere Emerson Aufnahmegeräte Handbücher
Emerson
Emerson SPS 4001B Bedienungsanleitung
Emerson
Emerson QuickPanel+ IC755C S06RD Series Bedienungsanleitung
Emerson
Emerson Keystone OM11 Bedienungsanleitung
Emerson
Emerson Bettis OM9-SCE300 Bedienungsanleitung
Emerson
Emerson IEC 62591 Bedienungsanleitung
Emerson
Emerson PACSystems Versamax Bedienungsanleitung
Emerson
Emerson Keystone OM9 Montage- und Bedienungsanleitung
Emerson
Emerson ROSEMOUNT Analytical IMPS 4000 Bedienungsanleitung
Emerson
Emerson SPS 4001B Bedienungsanleitung
Emerson
Emerson ROSEMOUNT Analytical SPS 4000 Series Bedienungsanleitung
Emerson
Emerson Blue Wireless Easy Install 1F98EZ-1621 Bedienungsanleitung
Emerson
Emerson USB Fieldbus Interface Bedienungsanleitung
Emerson
Emerson Keystone OM9 - EPI2 Bedienungsanleitung
Emerson
Emerson AE4-1395 Handbuch
Emerson
Emerson Bettis RTS Bedienungsanleitung
Emerson
Emerson ControlWave GFC IStran Bedienungsanleitung
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
