Emerson IE Series Bedienungsanleitung

Surge Protective Devices

IE Series

Page: B

Page: C

IE Series

Safety Information

Important Information

Read these instructions carefully and look at the equipment to become

familiar with the device before trying to install, operate, service or maintain it.

The following special messages may appear throughout thisbulletin or on the

equipment to warn of potential hazards or to call attention to information that

clarifies or simplifies a procedure.

The addition of either symbol to a “Danger”or “Warning” safety label

indicates that an electrical hazard exists which will result inpersonal

injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messagesthat follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided,

could result in minor or moderateinjury.

NOTICE

NOTICE is used to address practices not related to physical injury. The safety

alert symbol shall not be used with this signal word.

Please Note

Electrical equipment should be installed, operated, serviced, and maintained only

by qualified personnel. No responsibility is assumed by Appleton Grp LLC d/b/a

Appleton Group for any consequences arising out of the use of this material.

A qualified person is one who has skills and knowledge related to the

construction, installation, and operation of electrical equipment andhas received

safety training to recognize and avoid the hazards involved.

Page: 1

IE Series

Introduction

The IE Series offers high frequency noise lter capabilities with surge protection for loads up to 20 A of

continuous current. This product is a DIN or ange mounted device that helps to protect industrial

critical loads.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E,

NOM-029-STPS or CSA Z462.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Turn o󰀨 all power supplying this equipment before working on or inside equipment.

• Always use a properly rated voltage sensing device to conrm power is o󰀨.

• Replace all devices, doors and covers before turning on power to this equipment.

• This equipment must be e󰀨ectively grounded per all applicable codes. Use an equipment-grounding conductor to

connect this equipment to the power system ground.

• Do not supply more than 24VDC / 24VAC and no more than a current of 2A to contacts.

• Conrm that the Surge Protective Device voltage rating on the module or nameplate label is not less than the

operating voltage.

Failure to follow these instructions will result in death or serious injury.

WARNING: This product can expose you to chemicals including DINP, which is known to the

State of California to cause cancer, and DIDP which is known to the State of California to cause

birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov.

NOTICE

LOSS OF SURGE SUPPRESSION

• Make certain the Surge Protective Device is disconnected from the circuit it is protecting before conducting high

potential insulation testing.

Failure to follow these instructions can result in equipment damage.

IE Series

Page: 2

Installation

1. Turn off all power supplying this equipment before working on or inside equipment.

2. Conrm that the unit has the same voltage rating and conguration as the power system voltage and

power system voltage to which it will be connected.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Conrm that the Surge Protective Device voltage rating on the module or nameplate label is not less than the

operating voltage.

Failure to follow these instructions will result in death or serious injury.

3. Install the unit and cables as close as possible to the protected equipment and secure.

4. Connect the supply cables to the line side of the device.

5. Complete the circuit by connecting cables from the load of the device to the protected equipment.

Note: A dry contact connection is available.

6. Check that all connections are secure. Remove all tools and discarded hardware from the unit.

7. Replace the barrier, cover/door and/or trim to the equipment.

8. Equipment may be re-energized after all the above steps are complete.

Table 1: Ratings

Service Voltage MCOV Continuous

Current

Normal

Discharge

Current

Fusing Circuit

Breaker Size Certification Catalog

Numbers

120 V, 50/60 Hz,

1-phase

2 wire + ground

150 V

(L–N)

3 A

3 kA 25 A Class CC

Fuse

UL1449 /

UL1283 CSA

C22.2 No.

269.5

IE103

5 A IE105

10 A IE110

20 A IE120

240 V, 50/60 Hz,

1-phase

2 wire + ground

275 V

(L–N)

3 A IE203

5 A IE205

10 A IE210

20 A IE220

Page: 3

IE Series

Description Catalog Number

IE1XX IE2XX

Input Voltage 120 V (0–150 VRMS) 240 V (0–275 VRMS)

Line Frequency 47–63 Hz

Response Time < 0.5 ns normal mode; < 5 ns common mode

Enclosure Fully enclosed polycarbonate housing

Connection/Mounting Type DIN rail or Panel mount

Status Indication Green LED “OK”, Form C contact, 5 A @ 125 VAC or 5 A @ 100 VDC

Dimensions H x W x D 4.88 x 2.56 x 4.56in. (124 x 65 x 116mm)

Operating Temperature -40°C to +50°C at full load; derate linearly to 60% at +70°C

Operating Humidity 0% to 95% Non-condensing

Peak Surge Current Capability

Per Phase 19,500 A

Line to Neutral 13,000 A

Line to Ground 6,500 A

Neutral to Ground 6,500 A

Load Surge Current Rating

10 ms 5 x Nominal

1 s 3 x Nominal

10 s 2 x Nominal

Nominal Discharge Current Rating 3 kA

Short Circuit Current Rating (SCCR) 5kA

Maximum Continuous Operating Voltage (MCOV) 150V L-N, L-G, N-G 320 L-L

Frequent Response

Normal Mode (forward-reverse) 100 kHz to 50 MHz -90 dB Max

Common Mode (forward-reverse) 5 kHz to 50 MHz -60 dB Max

Transient Reduction (IEEE C62.41)*

*All Voltage congurations are single phase, 2 wire + ground

Typical Category A Ringwave (6 kV, 200 A, 100 kHz) < 60 V peak

Typical Category B Ringwave (6 kV, 500 A, 100 kHz) < 100 V peak

Standards Certication cRUus: UL 1449, CSA 22.2 No. 269, UL 1283, CSA 22.2 No. 8 (recognized component), CE

Warranty 5 year limited warranty

Voltage, Current and Power Configurations

Catalog Number Load Current Wire Size Range

(AWG)

Required

Torque (lb-in.)

Fuse/Circuit Breaker Ampacity

Suggest Max

Single-Phase Models (120 VAC)

IE103 3.0 A

12 - 14 12.1 lb-in. (1.37 N•m)

3.0 A 3.75 A

IE105 5.0 A 5.0 A 6.25 A

IE110 10.0 A 10.0 A 12.5 A

IE120 20.0 A 20.0 A 25.0 A

Single-Phase Models (240 VAC)

IE203 3.0 A

12 - 14 12.1 lb-in. (1.37 N•m)

3.0 A 3.75 A

IE205 5.0 A 5.0 A 6.25 A

IE210 10.0 A 10.0 A 12.5 A

IE220 20.0 A 20.0 A 25.0 A

IE Series

Page: 4

Table 2: General Specifications1

Mounting Power

Connection

Wiring

(Copper

Wire)

Terminal

Torque

Operating / Storage

Temperature

Catalog

Numbers

DIN rail or

surface mount

Line / Neutral /

Ground

18–12 AWG

4 lb-in.

(0.45

N•m)

+32 °F to +77 °F (0 °C to +25 °C)

IE103

IE105

IE110

IE120

14–10 AWG 7 lb-in.

(0.45

N•m)

IE203

IE205

12–10 AWG IE210

IE220

1 Contains no serviceable parts.

Figure 1: DIN Rail Installation and Removal

Figure 2: DIN Clips

Note: DIN-Rail clips can be positioned for vertical or horizontal installation.

Page: 5

IE Series

Figure 3: Connections and Wiring

LINE INPUT

FROM SOURCE

RELAY

CONTACTS

TO REMOTE

INDICATION

IF NEEDED

TO LOAD OR

EQUPMENT

TO PROTECT

NO COM NC

LINE LOAD

GND

L/L1

N/L2

GND

L/L1

N/L2

GND

Diagnostic Operation

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E,

CSA Z462, or NOM-029-STPS.

Failure to follow these instructions will result in death or serious injury.

Indicator Status ON =

The device is installed correctly and the line side has power.

Indicator Status OFF =

Check connections, verify that the line voltage is at the point of connection; if all is correct,

then replace the device.

Dry Contact Terminal Power OFF Power ON

N/O Normally Open Open Closed

COM Common Common Common

N/C Normally Closed Closed Open

IE Series

Page: 6

Dimensions (in. / [mm]) and weights (lb. / kg.)

3.83

[97.2]

3.06

[77.7]

4.06

[103.1]

3.83 in.

[97.2 mm]

3.06 in.

[77.7 mm]

4.06 in.

[103.1 mm]

Catalog

Numbers

Weights

(lb./kg.)

IE103 0.94 lb. (0.42 kg)

IE105 0.95 lb. (0.43 kg)

IE110 1.2 lb. (0.58 kg)

IE120 1.4 lb. (0.64 kg)

IE203 0.94 lb. (0.42 kg)

IE205 0.95 lb. (0.43 kg)

IE210 1.2 lb. (0.58 kg)

IE220 1.4 lb. (0.64 kg)

Page: 7

IE Series

Technical Support

Website: www.solahd.com

Technical Support E-Mail: solahd.technicalservices@emerson.com

Toll-Free: (800) 377-4384

USA: (847) 268-6651

Warranty

Please refer to the “Terms & Conditions of Sale” document.

While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp LLC d/b/a Appleton Group

assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Überspannungsschutz Handbücher

Emerson

Emerson STC-SLAC Series Bedienungsanleitung

Emerson

Emerson Liebert TYPE SS Bedienungsanleitung

Emerson

Emerson Liebert PSS NET 1080T Bedienungsanleitung

Emerson

Emerson AccuGuide ACGY1110808 Bedienungsanleitung

Emerson

Emerson SOLAHD STCCAT6P0EI Bedienungsanleitung

Emerson

Emerson SolaHD STC-DRS Series Bedienungsanleitung

Emerson

Emerson Interceptor II TVSS Bedienungsanleitung

Emerson

Emerson Liebert Surge and Signal Protection Bedienungsanleitung

Emerson

Emerson Islatrol RM-115-10R Bedienungsanleitung

Emerson

Emerson SolaHD SPD50K Series Bedienungsanleitung

Emerson

Emerson PowerSure PST Bedienungsanleitung

Emerson

Emerson SolaHD STC-642 Series Bedienungsanleitung

Emerson

Emerson PowerSure 350-500VA Bedienungsanleitung

Emerson

Emerson Liebert XDF Bedienungsanleitung

Emerson

Emerson 500 Series Bedienungsanleitung

Emerson

Emerson PanelGuard 65 Bedienungsanleitung

Emerson

Emerson AccuVar NEMA 4X Bedienungsanleitung

Emerson

Emerson SP-6TVN Bedienungsanleitung

Emerson

Emerson Liebert LM Series Bedienungsanleitung

Emerson

Emerson SolaHD STC-HSP Series Bedienungsanleitung

Emerson

Emerson Sola HD STV200K Series Bedienungsanleitung

Emerson

Emerson SOLAHD STV100K Series Bedienungsanleitung

Emerson

Emerson Liebert Precision Cooling Bedienungsanleitung

Emerson

Emerson SOLAHD STCPOE65FF Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung