Emerson Rosemount 2110 Bedienungsanleitung

Quick Start Guide

00825-0100-4029, Rev CB

November 2020

Rosemount™ 2110 Level Switch

Vibrating Fork

Contents

About this guide...........................................................................................................................3

Installation................................................................................................................................... 5

Prepare the electrical connections................................................................................................9

Connect wiring and power up.....................................................................................................14

Product certifications................................................................................................................. 17

Quick Start Guide November 2020

2 Rosemount 2110 Level Switch

1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 2110.

Refer to the Rosemount 2110 Reference Manual for more instructions. The

manual and this guide are also available electronically at Emerson.com/

Rosemount.

WARNING

Failure to follow safe installation and servicing guidelines could result in

death or serious injury.

•Ensure the level switch is installed by qualified personnel and in

accordance with applicable code of practice.

•Use the level switch only as specified in this manual. Failure to do so may

impair the protection provided by the level switch.

Explosions could result in death or serious injury.

•The level switch must only be installed and operated in non-hazardous

(ordinary) locations.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

•Ensure the power to the level switch is off, and the lines to any other

external power source are disconnected or not powered while wiring the

level switch.

•Ensure the wiring is suitable for the electrical current and the insulation is

suitable for the voltage, temperature, and environment.

Process leaks could result in death or serious injury.

•Ensure the level switch is handled carefully. If the process seal is

damaged, gas might escape from the vessel (tank) or pipe.

November 2020 Quick Start Guide

Quick Start Guide 3

WARNING

Any substitution of non-recognized parts may jeopardize safety. Repair (e.g.

substitution of components) may also jeopardize safety and is not allowed

under any circumstances.

•Unauthorized changes to the product are strictly prohibited as they may

unintentionally and unpredictably alter performance and jeopardize

safety. Unauthorized changes that interfere with the integrity of the

welds or flanges, such as making additional perforations, compromise

product integrity and safety. Equipment ratings and certifications are no

longer valid on any products that have been damaged or modified

without the prior written permission of Emerson. Any continued use of

product that has been damaged or modified without the written

authorization is at the customer’s sole risk and expense.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or

misconfiguration of end users’ equipment. This could be intentional or

unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for all

systems used within the facility.

CAUTION

Hot surfaces

The flange and process seal may be hot at high process

temperatures.

Allow to cool before servicing.

Quick Start Guide November 2020

4 Rosemount 2110 Level Switch

2 Installation

2.1 Fork alignment in a pipe installation

Figure 2-1: Correct Fork Alignment for Pipe Installation

A. Tri Clamp process connections have a circular notch

B. Threaded process connections have a groove

2.2 Fork alignment in a vessel (tank) installation

Figure 2-2: Correct Fork Alignment for Vessel (Tank) Installation

OK OK

A. Tri Clamp process connections have a circular notch

B. Threaded process connections have a groove

November 2020 Quick Start Guide

Quick Start Guide 5

2.3 Mounting the threaded version

2.3.1 Seal and protect the threads

•Use anti-seize paste or PTFE tape according to site procedures.

A gasket may be used as a sealant for BSPP (G) threaded connections.

2.3.2 Threaded vessel (tank) or pipework connection

•Vertical installation.

•Horizontal installation.

A. Tighten using the hexagon nut only

B. Gasket for BSPP (G) threaded connection

Quick Start Guide November 2020

6 Rosemount 2110 Level Switch

2.3.3 Threaded flange connection

Procedure

1. Place the customer-supplied flange and gasket on the vessel (tank)

nozzle.

A. Gasket (customer supplied)

2. Tighten the bolts and nuts with sufficient torque for the flange and

gasket.

3. Screw the level switch into the flange thread.

A. Tighten using the hexagon nut only

B. Gasket for BSPP (G) threaded connection

November 2020 Quick Start Guide

Quick Start Guide 7

2.4 Mounting the Tri Clamp version

Procedure

1. Lower the level switch into the flange face.

A. Seal (supplied with Tri Clamp)

2. Fit the Tri Clamp.

Note

The Tri Clamp and seal are supplied in an accessory kit that has to be

ordered separately. See the Rosemount 2110 Product Data Sheet for

ordering information.

Quick Start Guide November 2020

8 Rosemount 2110 Level Switch

3 Prepare the electrical connections

Note

See the Rosemount 2110 Product Data Sheet for all electrical specifications.

3.1 Cable selection

Twisted-pairs and shielded wiring is recommended for environments with

high EMI (electromagnetic interference). Two wires can be safely connected

to each terminal screw. Maximum wire size is 15 AWG.

3.2 Cable glands/conduits

The cable gland is integrated in the four-position plug of the level switch. Do

not make any modifications to the level switch.

3.3 Power supply

The Direct Load electronics operate on 21 - 264 Vdc or 21 - 264 Vac (50/60

Hz) at the level switch terminals.

The PNP electronics operate on 18 - 60 Vdc at the level switch terminals.

3.4 Mode selection

Table 3-1 shows how the mode selection is determined from the wiring

connections. Modes are “Dry on, high level alarm” and “Wet on, low level

alarm”.

November 2020 Quick Start Guide

Quick Start Guide 9

Table 3-1: Mode Selection By Customer Wiring

Modes Electronics option code 0 Electronics option code 1

Load switching: ac/dc

Direct load switching: ac/dc

PNP output: dc

PNP for PLC/SPS connection: dc

Dry = on, high level

alarm

Orientation

cut-out

PE (ground)

N (21-264 Vac,

50/60 Hz)

0 V (21-264 Vdc)+V

(T)

PE (ground)

PLC

input

(18-60 Vdc)

0 V +V

(T)

Wet = on, low level

alarm

Orientation

cut-out

PE (ground)

N (21-264 Vac,

50/60 Hz)

0 V (21-264 Vdc)+V

(T)

PE (ground)

PLC

input

(18-60 Vdc)

0 V +V

(T)

R = external load

(must be wired)

R = external load

Maximum inrush current: 5A (over current protected)

I maximum continuous: 500 mA

Voltage drop: 6.5 V @ 24 Vdc or

5.0 V @ 240 Vac

Voltage drop: less than 3 V

I load off: less than 3 mA I load off: less than 0.5 mA

Quick Start Guide November 2020

10 Rosemount 2110 Level Switch

Andere Handbücher für Rosemount 2110

Inhaltsverzeichnis

Andere Emerson Schalten Handbücher

Emerson

Emerson AVOCENT Bedienungsanleitung

Emerson

Emerson Rosemount 2120 Bedienungsanleitung

Emerson

Emerson ATCA-F120 Kurzanleitung

Emerson

Emerson Rosemount 2160 Bedienungsanleitung

Emerson

Emerson ASCO 300 Series Bedienungsanleitung

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2120 Bedienungsanleitung

Emerson

Emerson 200I/48-NT5C05C Bedienungsanleitung

Emerson

Emerson Rosemount 2130 Bedienungsanleitung

Emerson

Emerson PENBERTHY MGS-314L Series Handbuch

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Emerson

Emerson ASCO 300 Series Bedienungsanleitung

Emerson

Emerson PACSystems SLM042 Bedienungsanleitung

Emerson

Emerson Cybex SC KM 140 Bedienungsanleitung

Emerson

Emerson Rosemount 2120 Bedienungsanleitung

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Emerson

Emerson Avocent SV 220 Bedienungsanleitung

Emerson

Emerson Mobrey Series Gebrauchsanweisung

Emerson

Emerson SM-ETHERCAT 0471-0128-02 Bedienungsanleitung

Emerson

Emerson TARTARINI V/31-2-AP-E Series Bedienungsanleitung

Emerson

Emerson Rosemount 2140 Bedienungsanleitung

Emerson

Emerson HiSwitch2 Bedienungsanleitung

Emerson

Emerson Rosemount 2130 Bedienungsanleitung

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung