EMG PASSIVE Service-Handbuch

INSTALLATION INFORMATION

EMG MODELS: PASSIVE / PASSIVE

PO BOX 4394

SANTA ROSA, CA

95402 USA

P (707) 525-9941

F (707) 575-7046

EMGPICKUPS.COM

Diagram #1

2 Pickups

Toggle Style Switch

2 Volumes (Dependent)

Master Tone

Diagram #2

2 Pickups

Toggle Style Switch

2 Volumes (Dependent)

2 Tones

SEE PAGE 2 FOR WIRING WITH EMG SOLDERLESS TOGGLE SWITCHES

OR HARDWIRED 3-POSITION BLADE SWITCHES

VOLUME250K 500K

B159A

EMG

VOLUME250K

B159A

EMG

OUTPUT

NK VOLUME

FROM NECK PICKUP

FROM BRIDGE PICKUP

MASTER

TONE

OUTPUT CABLE

250K 500K

B160A

TONE

EMG

GROUND

BRIDGE P/U

NECK P/U

OUTPUT

BR VOLUME

TO STRING GROUND

SEE DIAGRAM #3

NK VOLUME

OUTPUT

FROM NECK PICKUP

FROM BRIDGE PICKUP

BR VOLUME

NK TONE

OUTPUT CABLE

250K 500K

B160A

TONE

EMG

GROUND

BRIDGE P/U

NECK P/U

OUTPUT

BR TONE

250K 500K

B160A

TONE

TO STRING GROUND

SEE DIAGRAM #3

B289 and B348 Toggle Switches

All EMG Solderless Toggle Switches use the same “BNOG” wiring scheme:

B= Bridge Pickup input (White wire)

N= Neck Pickup input (Red wire)

0= Output of Switch (Black wire)

G= Ground (Bare shield)

Install the 4 pin connector housing on the switch as shown

in the diagram to the right. Install the 2 separate 2 pin connectors

on to the 4 pin connector between the black and red housings as shown.

The black and green terminal blocks will not be used for the switch.

Reverse this connector to

make the switch work in

the opposite direction

B289

B348

1234

GROUND

BRIDGE P/U

NECK P/U

OUTPUT

Hardwired 3-Position Toggle and Lever Switch

To use your stock, hardwired selection

switch with the EMG Solderless Buss (B245),

strip the insulation from the switch wires,

insert them into the GREEN terminal block,

and tighten with a small screwdriver.

Bridge pickup > “BR” terminal

Neck pickup > “NK” terminal

Output > “O” terminal

Ground (if applicable) > “GND” terminal.

Page 2

Attaching the bridge ground wire

It is common to “ground” (earth) the strings on guitars

that have passive pickups. Included with the system is

a black wire with a single black connector attached.

Also included is an IDC connector for connecting the

two wires together. Insert the bridge ground wire, and

the connector wire into the IDC connector, crimp the

connector with a pair of pliers until it snaps and this

will connect the two wires. You don’t need to strip the

insulation from the wires. Push the black connector

onto a free ground terminal (GND) of the volume control as

shown in the diagram. This will ground the strings to the system.

Diagram #3

B159A

VOLUME250K

VOLUME

STRING GROUND WIRE

FROM THE BRIDGE

BLACK WIRE INCLUDED

WITH CONNECTOR

CLOSED

CRIMP

(INSERT WIRES)

Beliebte Zubehör für Musikinstrumente Handbücher anderer Marken

Behringer

Behringer AIRPLAY GUITAR AG10 Bedienungsanleitung

FEURICH

FEURICH BASIC Bedienungsanleitung

thomann

thomann Harley Benton JA Bedienungsanleitung

NeoTech

NeoTech PAD-IT TUBA HARNESS Bedienungsanleitung

Duncan

Duncan SH-8n Invader Kurzanleitung

Palmer

Palmer The Junction PDI-09 Bedienungsanleitung

GuitarPCB

GuitarPCB Fuzzy Bee v2 Handbuch

Yamaha

Yamaha Tough-Terrain T-335 Bedienungsanleitung

LEWISMIDI

LEWISMIDI CZ Patch Library Bedienungsanleitung

Free The Tone

Free The Tone LB-2 Bedienungsanleitung

Duncan

Duncan Apollo Jazz Bass - neck Handbuch

dbx

dbx dB10 Bedienungsanleitung

TLA

TLA Tuning-Set CTS-32-C Bedienungsanleitung

Solo Music Gear

Solo Music Gear JEK-1 Bedienungsanleitung

Duncan

Duncan HyperSwitch Bedienungsanleitung

CNC Design

CNC Design QUAD COIL WINDER MK2 Bedienungsanleitung

FuzzDog

FuzzDog 3PDT Bedienungsanleitung

Hipshot

Hipshot Universal Mounting Plate Bedienungsanleitung