EMKO ESM-4410 Bedienungsanleitung

ESM-4410 48 x 48 1/16 DIN Temperature Controller

-3D

- Selectable heating and cooling function

- Operating type selection with hysteresis

- Adjustment of temperature offset value

- Minimum pulling time adjustment for control outputs

- Password protection for programming mode

igits display

- NTC Input or,

PTC Input or,

J type thermocouple or,

K type thermocouple or,

PT-100 2-wire or 3-wire temperature input

( It must be determined in order )

- ON/OFF control form

ESM-4410 48 x 48 1/16 DIN

Digital, On/Off Temperature Controller

Instruction Manual. ENG ESM-4410 02 V03 04/08

Instruction manual of ESM-4410 Temperature Controller consists of three main sections.

Explanation of these sections are below. Also, there are other sections which include order

information and technical specifications of the device. All titles and page numbers in instruction

manual are in section. User can reach to any title with section number.

In this section, physical dimensions of the device, panel mounting, electrical wiring are

explained.

In this section, user interface of the device, how to access to the parameters, description

of the parameters are explained.

Configurable control function that is on the device is explained.

Also in these sections, there are warnings to prevent serious injury while doing the

physical and electrical mounting or using the device.

Explanation of the symbols which are used in these sections are given below.

“CONTENTS”

Installation:

Operation and Parameters:

Control Algorithm:

This symbol is used to determine the dangerous situations as a result of an electric

shock. User must pay attention to these warnings definitely.

cThis symbol is used for safety warnings. User must pay attention to these

warnings.

This symbol is used to determine the important notes about functions and usage of

the device.

ABOUT INSTRUCTION MANUAL

Page 5

Page 18

Page 12

Page 7

CONTENTS

1.PREFACE............................................................................................................................................

2.INSTALLATION....................................................................................................................................

3.ELECTRICAL WIRINGS......................................................................................................................

4.FRONT PANEL DEFINITION AND ACCESSING TO THE MENUS....................................................

5.PARAMETERS....................................................................................................................................

6.FAILURE MESSAGE IN ESM-4410 TEMPERATURE CONTROLLERS............................................

7.CONTROL ALGORITHM.....................................................................................................................

8.SPECIFICATIONS................................................................................................................................

1.1 GENERAL SPECIFICATIONS

1.2 ORDERING INFORMATION

1.3 WARRANTY

1.4 MAINTENANCE

2.1 GENERAL DESCRIPTION

2.2 FRONT VIEW AND DIMENSIONS OF ESM-4410 TEMPERATURE CONTROLLER

2.4 ENVIRONMENTAL RATINGS

2.5 PANEL MOUNTING

2.6 INSTALLATION FIXING CLAMP

2.7 REMOVING FROM THE PANEL

3.1 TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS

3.2 ELECTRICAL WIRING DIAGRAM

3.3 LABELS FOR ESM-4410 TEMPERATURE CONTROLLER

INPUT CONNECTION

3.5.1 TC (THERMOCOUPLE) CONNECTION

3.5.2 RTD CONNECTIONS

3.5.3 PTC AND NTC CONNECTIONS

3.6 GALVANIC ISOLATION TEST VALUES OF ESM-4410 TEMPERATURE CONTROLLER

3.7 OUTPUT ( RELAY OUTPUT ) CONNECTION

4.1 FRONT PANEL DEFINITION FOR ESM-4410

4.2 OBSERVATION OF ESM-4410 TEMPERATURE CONTROLLER SOFTWARE REVISION

4.3 CHANGING AND SAVING SET VALUE

4.4 ENTERING TO PROGRAMMING MODE, CHANGING AND SAVING PARAMETERS

5.1 SET PARAMETER

5.2 PROGRAM PARAMETERS

7.1 ON/OFF CONTROL

7.1.1 ON/OFF CONTROL IN ESM-XX10 TEMPERATURE CONTROLLERS

2.3 PANEL CUT-OUT

3.4 SUPPLY VOLTAGE INPUT CONNECTION OF THE DEVICE

3.5 TEMPERATURE

Page 28

Page 27

Page 30

Page 29

Manufacturer Company Name : Emko Elektronik A.S.

Manufacturer Company Address: DOSAB, Karanfil Sokak, No:6, 16369 Bursa, Turkiye

The manufacturer hereby declares that the product conforms to the following

standards and conditions.

Product Name :

Model Number :

Type Number :

Product Category :

Conforms to the following directives :

Temperature Controller

ESM-4410

Electrical equipment for measurement, control and laboratory use

73 / 23 / EEC The Low Voltage Directive as amended by 93 / 68 / EEC

89 / 336 / EEC The Electromagnetic Compatibility Directive

EN 61000-6-4:2001 EMC Generic Emission Standard for the Industrial Environment

EN 61000-6-2:2001 EMC Generic Immunity Standard for the Industrial Environment

EN 61010-1:2001 Safety Requirements for electrical equipment for measurement, control and

laboratory use

Has been designed and manufactured according to the following specifications

EU DECLARATION OF CONFORMITY

1.1 General Specifications

ESM-4410

Standard

Output (Relay

Output)

Glass

Plastic

Petro-Chemistry

Textile

Automative

Machine Production Industries

Application Fields

1.Preface

ESM series temperature controllers are designed for measuring and controlling

temperature. They can be used in many applications with On/Off control form and heating and

cooling selection. Some application fields which they are used are listed below:

Temperature Input

Supply Voltage

Input

Control Output

Alarm Output

Heating or Cooling

Function

ON/OFF Operation

NTC

PTC

JorKTypeTC

2or PT1003 wire

Standard

230 V (±%15) , 50/60 HzV

Optional Supply Voltage

Inputs

115 V (±%15) , 50/60 HzV

24 V (±%15) , 50/60 HzV

24 V ( - %15, + %10 )

50/60 Hz

1.2 Ordering Information

1.3 Warranty

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for a period of two years. The warranty period starts from

the delivery date. This warranty is in force if duty and responsibilities which are determined in

warranty document and instruction manual performs by the customer completely.

1.4 Maintenance

Repairs should only be performed by trained and specialized personnel. Cut power to the device

before accessing internal parts.

Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of

these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl

alcohol or water to clean the external plastic case.

All order information of ESM-4410

Temperature Controller are given on the

table at left. User may form appropriate

device configuration from information and

codes that at the table and convert it to the

ordering codes.

Firstly, supply voltage then other

specifications must be determined. Please

fill the order code blanks according to your

needs.

Please contact us, if your needs are

out of the standards.

Vac,

Vdc,

Vacdc

ÞW

ESM-4410 (48x48 1/16 DIN)

ABCD E FGHI /

UVWZ/

1000200

Output-1

Output-2FG

None

Supply Voltage

24 V (±15%) 50/60 HzV

Customer

115 V (±15%) 50/60 HzV

230 V (±15%) 50/60 HzV

J ,Fe CuNi IEC584.1(ITS90)

PTC (Note-1)

Input Type

BC Scale(°C)

-50°C 150°C

0°C 800°C

-19.9°C 99.9°C

PT 100 , IEC751(ITS90)

10 K ,NiCr Ni IEC584.1(ITS90)

400°C

0°C 999°C

PT 100 , IEC751(ITS90) 0°C

PTC (Note-1)

15 -19.9°C 99.9°C

Temp.Sensor which is given with ESM-4410

0None

1PTC-M6L40.K1.5

(PTC Air probe with 1.5 m silicon cable)

2PTCS-M6L30.K1.5.1/8”(PTC Liquid probe with 1.5 m silicon cable)

Relay Output(7 A@250 V at resistive load, 1NO)

19 -19.9°C 99.9°C

-50°C 100°C

NTC (Note-1)

Note-1 : If input type is selected PTC or NTC (BC = 12, 15, 18, 19 ),

Temperature sensor is given with the device. For this reason,

If input type is selected as PTC, sensor type (V = 0,1 or 2) or

If input type is selected as NTC, sensor type (V = 0,3 or 4) must be

declared in ordering information.

Customer

3NTC-M5L20.K1.5 (NTC Probe, thermoplastic moulded with

1.5 m cable for cooling application)

4NTC-M6L50.K1.5 (NTC Probe, stainless steel housing with

1.5 m cable for cooling application)

224 V ( - %15, + %10 ) 50/60 HzW

In package ,

- One piece unit

- One piece instruction manual

A visual inspection of this product for possible damage occured during shipment is

recommended before installation. It is your responsibility to ensure that qualified

mechanical and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power

off the system and the electrical connection of the device from the system.

The unit is normally supplied without a power switch or a fuse. Use power switch and fuse

as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to

prevent failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble

with the unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may

results in malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During the equipment is putted in hole on the metal panel while mechanical installation

some metal burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s own fixing clamps. Do not do

the montage of the device with inappropriate fixing clamps. Be sure that device will not fall

while doing the montage.

It is your responsibility if this equipment is used in a manner not specified in this

instruction manual.

- Two pieces mounting clamps

separate

Before beginning installation of this product, please read the instruction

manual and warnings below carefully.

2.Installation

2.1 General Description

2.2 Front View and Dimensions of ESM-4410 Temperature Controller

84 mm / 3.31 inch

ESM-4410

SET

OUT PROG

48 mm/ 1.89 inch

Maximum 5 0.2 inchmm /

11±1mm/0.43 inch

Mounting Clamp

Panel surface

(maximum thickness 5 mm / 0.2 inch)

Front Panel

IP65 protection

NEMA 4X

ESM-4410

2.3 Panel Cut-Out

65 mm / 2.56 inch (min)

46 mm / 1.81 inch (min)

Operating Temperature :

Max. Operating Humidity :

Altitude :

0to50°C

90 Rh (non-condensing)

Up to 2000 m.

Operating Conditions

Forbidden Conditions:

Corrosive atmosphere

Explosive atmosphere

Home applications (The unit is only for industrial applications)

2.4 Environmental Ratings

2.5 Panel Mounting

During installation into a metal panel, care should be taken to avoid injury from

metal burrs which might be present. The equipment can loosen from vibration

and become dislodged if installation parts are not properly tightened. These

precautions for the safety of the person who does the panel mounting.

1-Before mounting the device in your

panel, make sure that the cut-out is of

the right size.

2-Check front panel gasket position

3-Insert the device through the cut-

out. If the mounting clamps are on the

unit, put out them before inserting the

unit to the panel.

ESM-4410

Andere Handbücher für ESM-4410

Inhaltsverzeichnis

Andere EMKO Temperaturregler Handbücher

EMKO

EMKO ESM-9910 Bedienungsanleitung

EMKO

EMKO ESM-3710 Bedienungsanleitung

EMKO

EMKO ESM-7710 Bedienungsanleitung

EMKO

EMKO ESM-1510-N Bedienungsanleitung

EMKO

EMKO ESM-3770-D Bedienungsanleitung

EMKO

EMKO ESM-3710-N Bedienungsanleitung

EMKO

EMKO ESM Series Bedienungsanleitung

EMKO

EMKO ESM-9910.5.12.0.1/01.00/2.0.0.0 Bedienungsanleitung

EMKO

EMKO ESM-3712-HCN Bedienungsanleitung

EMKO

EMKO ESM-3710-N Bedienungsanleitung

EMKO

EMKO ESM-3723 Bedienungsanleitung

EMKO

EMKO ESM-4420 Bedienungsanleitung

EMKO

EMKO ESM-3712-HCN Bedienungsanleitung

EMKO

EMKO ESM-3712-HC Bedienungsanleitung

EMKO

EMKO ESM-3711-H Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung