Emos AP emGo-U25 Bedienungsanleitung

AP emGo-U25

WIFIROUTER/REPEATER/CLIENT

CZ WIFIROUTER/OPAKOVAČ/KLIENT

SK WIFI ROUTER/OPAKOVAČ/KLIENT

PL WIFI ROUTER/REPEATER/KLIENT

HU WIFI ROUTER/JELERŐSÍTŐ/KLIENS

WIFI USMERNIK/REPETITOR/KLIENT

WIFI ROUTER/REPETITOR/KLIJENT

DE WIFI ROUTER/REPEATER/KLIENT

UA WIFI /

/KLIENT

RO WIFI ROUTER/REPETOR/CLIENT

LT WIFIROUTER/REPEATER/CLIENT

LV BEZVADU RŪTERIS/ATKĀRTOTĀJS/

KLIENTS

www.emos.cz

6 7

WIFIROUTER/REPEATER/CLIENT

it can be found at the website http:// shop.emos.cz/

download-centrum/.

The product may be operated under the general license No.

VO-R/12/09.2010-12

Setting U25

There are two ways how to connect the U25 repeater to your

home router or modem:

• Automated connection using theWPS function (only in

the repeater mode) Figure 1

• Manual setting up of the connection. Requires a pass-

word to connect to the network. Figure 2

1. Automated connection to a home gateway or

router and its setting by the WPS function (in

the repeater mode)

U25 contains the function of automated setting

ofthe repeatermode.So youan easilyextendthe

range of your wireless network without any

knowledge of the IT technology.

a. If you have already made U25 changes in the settings,

delete them and reset to factory defaults.

b. PushtheWPS button onyourhome router, toactivatethe

WPS function (WPS icon on your router starts blinking).

Most modern routers have this function. Find a descrip-

tion of this function in the manual to your equipment.

c. Now push the WPS button on the repeater U25 for ca 5

seconds. You need to push the WPS button within one

minutefromtheactivationofthisfunctionin yourrouter.

d.The U25 repeater now automatically connects to the

router via a protected WPS connection. During the

connection the blue diode in U25 will be blinking.

e. Assoon asthe automaticcongurationofthe connection

has been completed (maximum 2 minutes), your

repeaterisreadytouse.U25willtransmit thesame SSID

network name as your router with the sux -ext

f. The password forconnecting clientsto thenewly created

network will be the same as the original password

to your home router.You can disconnect the repeater

fromthepower supplyandmove toadierent location.

INSTRUCTIONS AND INFORMATION

ABOUT USED PACKAGING DISPOSAL

Dispose of the used packaging in a waste disposal facility

designated by your municipality.

DISPOSAL OF USED ELECTRIC AND

ELECTRONIC APPLIANCES

Thissymbol ontheproducts orinthe accompa-

nying documents means that the used electric

and electronic products must not be discarded

in normal communal waste. Special collection

pointsare tobeusedfor properdisposal,renew-

al and recycling. As an alternative, in some EU

countries or other European countries you can return the

productstothelocalretailerwhenbuying anequivalent new

product.By properdisposalofthe productyouhelptoprotect

valuable natural resources and you help to prevent negative

impacts on environment and human health, which might

occur in case of improper waste disposal. Ask for more infor-

mation from your local authorities or the nearest waste col-

lection point. Improper liquidation of this type of waste may

lead to penalties according to national regulations.

For corporate entities in the European Union

If you need to dispose of electric and electronic appliances,

request information from your seller or supplier.

Liquidation in countries outside the EU

Thissymbol isvalid inthe EuropeanUnion. Ifyou

wishto disposeof thisproduct,requestinforma-

tion about proper disposal method from the

local authorities or from your seller. This product complies

withtheEUregulationsaboutelectromagneticcompatibility

and electric safety. Changes in the text, design and technical

specications may occur without prior warning and we re-

serve the right to make such changes.

Emos spol. s r.o. declares, that emGo U25 complies with

the basic requirement and other provisions of the directive

1999/5/EC.

This appliance may be operated freely within the EU. The

Declaration of Conformity is part of the instructions or

After reconnection of U25 to the power supply, the

setting will remain unchanged.

2. Manual setting of the connection to U25

If you want to use other ways to connect U25, you have to

set it via the web interface. Connect to U25 according to the

following instructions.

Examples of connection and operating modes

Fig. 3

Access point mode

The Ethernet port works like LAN, U25 is connected to the

home gateway or ADSL modem via a UTP cable. Computers

fromyour homenetwork havewirelessconnectionto U25.IP

addressesare allocatedbythehome gateway, routeror ADSL

modem. In the computer connected to U25 the IP address

can be set by means of DHCP. The factory default SSID of

the wireless network is U25 (can be changed). The default

password for connection to U25 is 123456789.

Uses for this type of connection: hotel, household etc.

Home gateway / router mode

The Ethernet port works like a WAN port and it is directly

connectedtoInternet viaa UTP cable. Computersfromyour

homenetworkhavewireless connectiontoU25.IPaddresses

are allocated to the computers in the inner network by U25

via its own DHCP server from the series 192.168.10.1 –

192.168.10.255. NAT translation of IP addresses is on.

The inner LAN network is isolated form the WAN network.

The default SSID of the wireless network is U25 (can be

changed). The default password for the connection to U25

is 123456789.

Use of this type of connection: hotel, household, oce etc.

Figure. 4

WiFi signal repeater / booster mode

The repeater operating mode is used to extend the signal

range of an existing WiFi network from AP or a wireless

router. Computers can be connected to U25 via a cable

or wireless connection. U25 is connected to Internet and

inner network wirelessly. The IP address of DNS is allocated

by the original router or a home gateway. U25 relays all

incoming and outgoing communication unchanged to the

extended network.

Use of this type of connection: bigger houses, villas, trans-

mission among buildings, gardens etc.

WISP repeater mode (repeater with an

integrated router)

The repeater operating mode is used to extend the signal

range of an existing WiFi network from AP or a wireless

router. Computers can be connected to U25 via a cable or

wireless connection. U25 is connected to Internet and inner

network wirelessly. IP addresses are allocated to computers

of the inner network by U25 via its own DHCP server of the

series 192.168.10.1 – 192.168.10.255. NAT translation

of IP addresses is on.

Use of this type of connection: bigger houses, villas, trans-

mission among buildings, gardens etc.

Fig. 5

WiFi client mode

In this mode U25 works as a wireless adapter and it can

be used to connect appliances without an integrated WiFi

network card to a WiFi network. PC is connected to U25 via

a solid UTP cable and it has a wireless connection to a home

WiFigatewayorrouter.IPaddressesareallocatedbythe home

gateway, routeror ADSLmodem.In acomputer connectedto

U25 the IP address can be set by means of DHCP. Usually this

mode can be used to connect multimedia appliances such as

Smart TV, older PC, satellite receivers.

Use of this type of connection: IP cameras, older PC, Smart

TV, satellite receivers.

WISP client (client with an integrated router)

In this mode U25 works as a wireless adapter and it can

be used to connect appliances without an integrated WiFi

network card to a WiFi network. PC is connected to U25 via

a solid UTP cable and it has a wireless connection to a home

WiFi gateway or router. IP addresses to the computers in the

innernetworkareallocated byU25 viaits ownDHCP server of

theseries 192.168.10.1– 192.168.10.255.NATtranslation

of IP addresses is on. In a computer connected to U25 the IP

address can be set by means of DHCP. Usually, this mode can

be used to connect multimedia appliances such as Smart TV,

older PC, satellite receivers.

Use of this type of connection: IP cameras, older PC, Smart

TV, satellite receivers.

Connection of PC to U25 and the settings

Fig. 6

Click Start - Control panels – Network and Internet – Net-

works and Sharing Centre – Change Adapter Settings”and

right click on “Wireless network connection” and choose

“Connect”.

Fig. 7

On the PC desktop in the system part of the panel, left click

on the network wireless connection icon (make sure your

wireless network card is activated).

Fig. 8

From the list of wireless networks choose SSIDU25 and

click“Connect.”

Fig. 9

Enter the network password to connect to the wireless net-

workand conrmthe connectionbyclickingthe “OK”button.

The default password and SSID network name is written on

the repeater label.

Fig. 10

Afterchecking thepasswordthe listwilldisplaytheicon“Con-

nected”, which indicates that the computer has successfully

been connected to the equipment.

Fig. 11

Open the web browser (Internet Explorer, Firefox, Safari,

etc.) and enter http://192.168.10.1 on the address line

(orthe Googlesearchline)andpush ENTERon thekeyboard.

Fig. 12

A new window will appear where you can enter the login

name and password.The default name: admin and default

password: admin.The password for access can be changed

in the web interface in the advanced settings.

Setting of the wireless parameters depends

from the selected operating mode

Router or AP (Access Point) mode

Fig. 13

Click Access Point or Router according to the mode you

wish to choose.

Fig. 14

Choose the name of the SSID in your new wireless network

(default: U25) and password to secure the network. The

password must be at least 8 symbols long.

Fig. 15

Set the WAN connection to Internet. You can choose from

the oer: static IP address, dynamic IP address allocated

by the DHCP server or PPPoE Dial-Up. If you are not sure,

choose DHCP. After the setting, click the icon ”Save/Apply”

to store the settings.

Repeater

Fig. 15 - 17

Click the icon Repeater, or Repeater WISP (Fig. 12) to

choosethe repeatermodeandthenclicktheicon“SiteSurvey”

tond anyavailablenetworksaround.Inthe“Select”column

click the line of the desired SSID network. In the eld Pre-

Shared Key: enter the password to connect to the chosen

WiFinetwork(the samepasswordisforaccess tothe extended

networkwith thehelpof therepeater).After thesetting,click

the icon ”Save/Apply” to store the setting.

Repeater WISP

The same setting as in the repeater.

Client mode

Clickthe iconClientorClientWISP(Fig.12) tochose theClient

modeorWISPClientmodeand thenclick“SiteSurvey”iconto

nd all available networks around. In the “Select” column

click the line of the desired SSID network. In the eld Pre-

Shared Key: enter the password to connect to the chosen

WiFinetwork. Afterthesetting, clicktheicon “Save/Apply”

tostore thesetting. Aftersettingthe U25 tothe Client mode,

disconnect it from PC and connect to the multimedia appli-

ance.The setting will remain and the multimedia appliance

will be connected automatically.

Wisp client

The setting is the same as the client.

Fig. 18 – 19

Equipment reset and restoration of the defaults

ActivateU25 andleaveiton. Holdthe resetbuttononthe side

oftheappliance forat least5seconds untiltheblue indicator

diode goes dark for moment. All settings will be deleted and

factory defaults will be restored.

•To see more advanced setting options click the icon

“Advanced“.

Inhaltsverzeichnis

Sprachen:

Andere Emos WLAN-Router Handbücher

Emos

Emos USBee Car D4 Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Milesight

Milesight UG67 Bedienungsanleitung

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v4 Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung