Empire Comfort Systems DVCT50CBP95N-1 Bedienungsanleitung

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

This appliance may be installed in an

aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certied kit is used.

This replace is design

certied in accordance

with American National

Standard/CSA Standard

ANSI Z21.88/CSA 2.33

and by Underwriters

Laboratories as a Direct

Vent Gas Fireplace

Heater and shall be

installed according to

these instructions.

GAS-FIRED

UL FILE NO. MH30033

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and shall

be installed for the protection of children and other at-risk

individuals.

(SEE HOMEOWNER MANUAL FOR OPERATING INSTRUCTIONS)

DIRECT VENT

ZERO CLEARANCE GAS

FIREPLACE HEATER SERIES:

DVCT50CBP95(N,P)-1

INSTALLATION INSTRUCTIONS

38267-1-0319Page 2

TABLE OF CONTENTS

Standard Work Checklist .............................................................................................................................................3

Before You Start .......................................................................................................................................................4-5

Carton Contents And Hardware ..................................................................................................................................6

Introduction ..................................................................................................................................................................7

Homeowner Reference Information ............................................................................................................................7

Specications ..............................................................................................................................................................8

Accessories .................................................................................................................................................................8

Fireplace Dimensions ..................................................................................................................................................9

Blower Installation ................................................................................................................................................10-11

Clearances ................................................................................................................................................................12

Vent Termination Clearances .............................................................................................................................. 13-14

Gas Supply ................................................................................................................................................................15

Locating Fireplace .....................................................................................................................................................16

Electrical Considerations ...........................................................................................................................................16

Component Wiring Diagram ......................................................................................................................................17

Installation ........................................................................................................................................................... 18-21

Vent Framing ....................................................................................................................................................... 22-23

Vent System Identication .........................................................................................................................................24

Special Vent Systems ................................................................................................................................................24

Venting Fireplace ................................................................................................................................................. 26-27

Horizontal Termination ...............................................................................................................................................28

Vertical Termination ............................................................................................................................................. 29-31

Air Shutter Adjustment ...............................................................................................................................................32

Control System Troubleshooting ..........................................................................................................................34-35

Accessing Valve Compartment .................................................................................................................................36

Testing Gas Supply ...................................................................................................................................................37

Parts List ...................................................................................................................................................................38

Exploded View ...........................................................................................................................................................39

Maintenance And Service ..........................................................................................................................................40

Important Safety Information .....................................................................................................................................41

Important Safety Information - Installer .....................................................................................................................42

Requirements For Massachusetts .............................................................................................................................43

Master Parts Distributor List ......................................................................................................................................44

How To Order Repair Parts .......................................................................................................................................44

Appliance Service History ....................................................................................................................................45-46

Warranty ....................................................................................................................................................................47

Multifunction Remote Operating Instructions ...................................................................... See Homeowners Manual

SECTION PAGE

38267-1-0319 Page 3

ATTENTION INSTALLER:

Follow This Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instruction manual.

Customer: _____________________________________

Lot/Address: ___________________________________

_______________________________________________

Model: ________________________________________

Serial # ________________________________________

Date Installed: _________________________________

Fireplace Location: _____________________________

Installer: ______________________________________

Dealer Phone #: ________________________________

______________________________________________

Empire recommends the following:

• Photograph the installation and copying this checklist for your le.

• Keep this checklist visible on the replace until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/Builder/Other, etc) and corrective action needed:

___________________________________________________________________________________________________________

Comments communicated to party responsible _____________________by_____________________ on ______________________

DVCT50CBP95(N,P)-1

FIREPLACE INSTALLATION COMMENTS

Veried clearances to combustibles. (pg. 12) ...................................................................... o____________________

Fireplace is leveled and secured. ........................................................................................ o____________________

VENTING / CHIMNEY

Venting conguration complies to vent diagrams. (pg. 27) .................................................. o____________________

Venting installed, locked, secured in place with correct clearance. ..................................... o____________________

Firestops installed. ............................................................................................................... o____________________

Exterior wall/roof ashing installed and sealed. ................................................................... o____________________

Terminations installed and sealed. (pgs. 28-31) .................................................................. o____________________

Light unit and test venting before enclosing the replace. ................................................... o____________________

ELECTRICAL (pgs. 16-17)

Unswitched power (110-120 VAC) provided to the appliance. ............................................ o____________________

GAS (pg. 15)

Proper appliance for fuel type. ............................................................................................. o____________________

Was a conversion performed? .............................................................................................. oYes oNo

Leak check performed and inlet pressure veried ................................................................ o____________________

FINISHING ( pg. 19)

Non-combustible board used as required............................................................................. o____________________

Veried all clearances meet installation manual requirements. ........................................... o____________________

Mantels and wall projections comply with installation manual requirements. ...................... o____________________

Granite or Clean Face nishing complete and complies with clearance

requirements in installation manual. .................................................................................... o____________________

Barrier screen for glass properly installed. .......................................................................... o____________________

FIREPLACE SETUP

All packaging and protective materials removed (inside & outside of appliance) . ............... o____________________

Media installed correctly. ..................................................................................................... o____________________

Firebox glass assembly cleaned, installed, and secured. ................................................... o____________________

Accessories installed properly. ............................................................................................ o____________________

Manual envelope and all of its contents are removed from inside/outside the

appliance and given to party responsible for use and operation. ........................................ o____________________

Started Appliance and veried no gas leaks exist. .............................................................. o____________________

38267-1-0319Page 4

BEFORE YOU START

Television Considerations

Installing a television above a replace has become increasingly

popular; however, the area above any replace gets hot and most

TV manufacturers recommend against placing their products near

a heat source.

If you install a television above this replace, Empire Comfort

Systems accepts no responsibility for damage or injuries. Follow

the television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

If you have a TV above your replace, turn off the replace and let it

cool completely before servicing or touching any buttons on the TV.

Samples, Warnings, and Denitions:

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE: Addresses practices not related to personal injury.

Read all instructions before starting installation and

follow them carefully to ensure safety. Failure to follow

the instructions will void the warranty and may cause

a re hazard.

The warranty will be voided by, and the warranter disclaims

any responsibility for the following actions:

• Installation by anyone other than the dealer or his agent.

• Installation of any damaged replace or component.

• Modication of the replace or direct vent system.

• Installation other than as instructed by Empire Comfort

Systems.

• Improper positioning of logs, glass door, or accessories.

• Installation and/or use of any component part not

manufactured or approved by Empire Comfort Systems.

All correspondence should refer to complete Model Number,

Serial Number and type of gas. Fill out the Homeowner

Reference Section on (Page 7).

Unpacking The Fireplace

1. Remove the outer boards/crate by removing screws.

2. Cut away shrink-wrap material around the unit. Retain

instruction manual and instruction sheets.

3. Remove (2) screws securing unit to pallet.

4. Get help to lift unit off of the pallet using the handles.

5. Remove non-combustible board from the pallet and place in

a safe location. It will be needed for installation.

6. Logs may remain in unit until installation in wall. Instruction

sheet from step #2 shows how to remove barrier screen and

glass door.

38267-1-0319 Page 5

BEFORE YOU START (CONT’D)

Accessories

Most accessories install much more easily before tting the replace

to the opening.

For example, it takes just 10-15 minutes to install the blower through

the back of the unit. Once the replace is framed in, it takes up

to an hour.

TrueFlame Technology

This replace is equipped with TrueFlame Technology for maximum

ames and ember glow with minimum emissions. The system

includes independently controlled front and rear burners set into a

large ember bed plus a ceramic catalyst and externally adjustable

bafe mounted at the top. Once adjusted by the dealer/technician at

installation, the TrueFlame system requires no scheduled service.

Preparation

This fireplace and its components are safe when installed in

accordance with this Manual. Report any parts damaged in shipment

to your dealer. Do not install the replace with damaged, incomplete

or substitute parts.

Installation Considerations

• Gas supply piping – right side entrance

• Electrical supply and connections

• 120V, 60Hz, 1 Amp

• Right side entrance

• Allowable replace mounting surfaces:

• A at, hard, combustible or non-combustible surface

• A raised platform of combustible or non-combustible material.

• The four corners of the replace onto non-combustible material

so that contact is made on all four perimeter edges on the

bottom of the replace – such as on cinder blocks

(where allowed by local codes).

• If the replace is installed directly on carpeting, tile or other

combustible material other than wood ooring, it should be

installed on a metal or wood panel extending the full width and

depth of the replace.

• This replace is designed to be installed in a zero-clearance

enclosure. Combustible material can come in contact with the

side standoff spacers, and the replace can be secured to

combustible framing with the framing brackets provided with

the replace.

Planning the installation

First determine where the fireplace will be located and what

accessories will be installed.

Your location must allow for:

• Venting – either vertical or horizontal. Choose a vent conguration,

(See Pages 28-31) and make sure the required access through

attics and walls is not blocked by other utilities such as water

lines, sewer vents, gas lines, etc. If access is blocked, you will

need to move the utilities or relocate the replace.

• Gas supply piping (right side entrance) – see pipe size and

specs on (Page 15).

• Electrical supply requirements

(120V, 60Hz, 1 Amp) (right side entrance)

• Proper framing required for installation of the replace.

See framing dimensions on (Page 18).

• Finishing the fireplace – drywall thickness, tile or stone

thickness, and the desired decorative accessories can affect

how you frame the opening and how you attach the nailing

anges to set the proper depth. (See Page 19) for nishing

details, before you begin.

38267-1-0319Page 6

CARTON CONTENTS

INDEX

NUMBER DESCRIPTION QUANTITY

SUPPLIED

1 Unit 1

2 AAA Batteries 3

3 AA Batteries 4

4Rockwool 2 Bags

5Drywall Screws 5

Non-Combustible Board (on pallet)

7Remote 1

8 Battery Holder & Switch 1

See Parts Lists on page 61 for ordering replacement parts. Do not order batteries, bolts, screws, washers or nuts.

They are standard hardware items and can be purchased at your local hardware store.

CARTON CONTENTS AND HARDWARE

Rock

wool Rock

wool

Under Pallet

IMAGE NOT TO SCALE

NOTICE: Re-Install Screws After Unpack (Outer Bottom)

38267-1-0319 Page 7

INTRODUCTION

The information in this manual pertains to all models and gas

control systems unless otherwise noted.

Instructions to Installer

1. Leave this manual with Homeowner.

2. Have the homeowner complete the Product Registration

Card or register online at www.empirecomfort.com

3. Show the homeowner how to start and operate the replace.

Notes to Installer

• This replace is designed to:

- Operate with combustion air siphoned from outside of

the building.

- Expel all exhaust gases to the outside of the building.

• The installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code

ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation

Code, or CSA B149.1 in Canada. * Available from the

American National Standards Institute, Inc. 11 West 42nd

St., New York, N.Y. 10036

• Any alteration of the original design, installation other than

as shown in these instructions, or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

• This replace is not for use with solid fuels.

• These replace models may be installed in a bedroom or

bed-sitting room in the U.S.A. and Canada.

WARNING

Any change to this replace can be dangerous. Improper

installation or use can cause serious injury or death from re,

burns, explosion or carbon monoxide poisoning.

Fireplace Certication

This replace is design certied in accordance with American

National Standard/CSA Standard ANSI Z21.88/CSA 2.33 and by

Underwriters Laboratories as a Direct Vent Gas Fireplace Heater

and shall be installed according to these instructions.

Consult your local building code agency, prior to installation,

to ensure compliance with local codes-including permits and

inspections.

The replace, when installed, must be electrically grounded in

accordance with local codes or, in absence of local codes, with

the National Electric Code ANSI/NFPA 70 or Canadian Electric

code, CSA C22.1, if an external electrical source is utilized.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of equipment

shall be performed only by a qualied agency. The term “qualied

agency” means any individual, rm, corporation or company

which either in person or through a representative is engaged

in and is responsible for (a) the installation or replacement of

gas piping or (b) the connection, installation, repair or servicing

of equipment, who is experienced in such work, familiar with all

precautions required and has complied with all the requirements

of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation must be

made by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

High Altitude (USA)

When installing this replace at an elevation above 2000 feet

(in the United States) it may be necessary to decrease the input

rating by changing the existing burner orice to a smaller size.

Generally, input should be reduced 4 percent for each 1000

feet above sea level. However, if the heating value of the gas

has been reduced, this general rule may not apply. Check with

Empire Comfort System’s local gas utility for proper orice size

identication.

High Altitude (CANADA)

Altitude: 0-4500 feet (0-1370 m)

When installing this replace at an elevation above 4500 feet

(in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the

proper orice for your location.

HOMEOWNER REFERENCE INFORMATION

We recommend that you record the following information about your replace.

Model Number: _____________________________ Date purchased: ________________________

Serial Number: _____________________________ Location of replace: _____________________

Dealer Name: ______________________________ Dealer Phone: _________________________

Notes: ______________________________________________________________________________

38267-1-0319Page 8

SPECIFICATIONS

Model Number DVCT50NAT DVCT50LP

Input BTU/Hr Maximum (w/ both burners on) 56,500 55,000

Input BTU/Hr Minimum (w/ both burners on) 38,000 44,000

Input BTU/Hr Minimum (front burner on only) 16,500 26,000

KWH (Maximum) 16.56 16.12

KWH (Minimum) 11.14 12.90

Orice - Front #41 #51

Orice - Rear #32 1.4mm

Air Shutter Opening Front Full Closed Full Opened

Air Shutter Opening Rear Full Closed Full Opened

Height without standoff (inches) 48-11/16 48-11/16

Width (inches) 56 56

Depth (inches) 24-1/2 24-1/2

Gas Inlet Shutoff Valve (pipe) 1/2 NPT 1/2 NPT

NOTE: Air shutter is at factory-minimum settings. Some vent congurations may require minor air shutter adjustments for optimum performance.

GAS SUPPLY PRESSURES (inches water column)

Gas Type Maximum Minimum Manifold

Natural 14 4.5 3.5

Propane 14 10.8 10

VENTING LIGHT BULB REPLACEMENT

5 x 8 Direct Vent System 35w Clear Halogen, Bi-Pin 6.35mm base,120vac, UL

ACCESSORIES

The following accessory parts can be obtained from your Empire Comfort Systems dealer. For additional information beyond what your dealer

can furnish, contact Empire Comfort Systems Inc., 918 Freeburg Ave., Belleville, Illinois 62220-2623.

Model Number Description

DVP50P... A liner is required. Contact your Empire Comfort Systems Dealer for available liner.

FBB21 Blower, Auto Variable-Speed - Twin

DFF50FPD Decorative Front, Forged Iron Frame, Distressed Pewter

DFF50RPD Decorative Arch Insert, Forged Iron, Distressed Pewter

DFF50CPD

Decorative Rectangle Insert, Forged Iron, Distressed Pewter (Requires DFF50FPD)

DCA1ABL Andirons, Black

Model Number CONVERSION KITS

Description

38226 Conversion Kit, IP System Natural to Propane

38227 Conversion Kit, IP System Propane to Natural Gas

LOG SETS

Model Number Description

LS50TINF Log Set for TruFlame Insert, Fiber - Traditional - Charred

NOTE: A liner kit and log set must be purchased and installed in order to operate the unit.

38267-1-0319 Page 9

FIREPLACE DIMENSIONS

INDEX LETTER DIMENSION DESCRIPTION DIMENSION IN INCHES

A The maximum height of replace face 47-3/4

BThe maximum width of the replace face 58

C The maximum depth of the replace 24

D The height of the replace opening 41-1/2

E The width of the replace opening 51

F The interior depth of the replace 19-1/4

G The rear exterior width of the replace 36-3/16

HThe height to the replace standoffs N/A

I Width from the left side to the centerline of vent 21

JDepth from back to centerline of top vent 10

KHeight from the bottom to the gas line opening 12-1/4

LDepth from the front to gas line opening 19-3/4

M Depth from rear to gas line opening 4-3/8

N Glass height 36-9/16

O Glass width 47-3/8

PDepth from front to centerline of vent 14

QDistance from oor to replace opening 1-1/2

R Height from oor to vent collar 48-11/16

N/A - Not applicable for this unit.

Figure 1

38267-1-0319Page 10

BLOWER INSTALLATION

Bench Installation

1. Remove Blower Access Panels. See Figure 2.

Figure 2

2. Place Blowers onto blower brackets. See Figure 3.

Figure 3

3. Bend tab as shown in Figure 4 and secure with

(2) screws.

HAND BEND

TAB INWARD

HAND BEND

TAB INWARD

Figure 4

4. Remove protective connectors on Wire Assembly from

replace and discard. Connect Wire Harness to both blowers

and the other end to the Wire Assembly supplied with the

replace. See Figure 5.

TO WIRE ASSEMBLY

(MODULE)

TO WIRE ASSEMBLY

(MODULE)

Figure 5

Replace Blower Access Panels removed in step 1.

See Figure 1.

Installation After Placement of Unit in Wall

1. Remove the following items. See Figure 6.

• Screen barrier (See Homeowner’s Manual, Maintenance

and Service).

• Glass Frame Assembly (See Homeowner’s Manual,

Maintenance and Service).

• Liners (See separate liner instruction document).

Figure 6

2. Remove front and rear burner. See Figure 7.

Figure 7

CAUTION

Sharp edges. Use protective gloves when installing.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Empire Comfort Systems Gasheizung Handbücher

Empire Comfort Systems

Empire Comfort Systems VFSR-16-4 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFRU24N-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSR-16-3, VFSR-18-3, VFSR-24-3, VFSR-30-3, VFSV-16-3, VFSV-18-3, VFSV-24-3, VFSV-30-3, VFSM-18-3, VFSM-24-3,... Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFYM-16RWO-2 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFD10CC series Bedienungsanleitung

Empire Comfort Systems

Empire Comfort Systems VFSR-16-5 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSUR18-2 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems SR-18T-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSE-18-1 Bedienungsanleitung

Empire Comfort Systems

Empire Comfort Systems VFCM-25-3 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems LTH718ST-1 Bedienungsanleitung

Empire Comfort Systems

Empire Comfort Systems PIONEER LPR36-1 Bedienungsanleitung

Empire Comfort Systems

Empire Comfort Systems VFNR-24N-1 Bedienungsanleitung

Empire Comfort Systems

Empire Comfort Systems FLINT HILL VFDR18LB10N-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSE-18-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems KENSINGTON LKF-2 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFNR-24-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems Sr-30-1 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFDR18LBW10N-4 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSM-30-3 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems LS-16C-2 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFSUR18-3 Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems VFRL1810 Series Kurzanleitung

Empire Comfort Systems

Empire Comfort Systems GREAT LAKES OAK LGLO 18-1 Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung