Empire DVCT40CFP95N-1 Planungshandbuch

Page 1Empire Comfort Systems Inc. • Belleville, Illinois

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

DIRECT VENT ZERO CLEARANCE

GAS FIREPLACE HEATER SERIES:

DVCT36CFP95N-1 DVCT40CFP95N-1

DVCT36CFP95P-1 DVCT40CFP95P-1

This replace is design

certied in accordance

with American National

Standard/CSA Standard

ANSI Z21.88/CSA 2.33

and by Underwriters

Laboratories as a Direct

Vent Gas Fireplace

Heater and shall be

installed according to

these instructions.

GAS-FIRED

UL FILE NO. MH30033

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and shall

be installed for the protection of children and other at-risk

individuals.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

This appliance may be installed in an

aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certied kit is used.

HOMEOWNER’S MANUAL

37743-1-0117Page 2

WARNING

Do not attach combustible material above your replace.

This is a re hazard. No greeting card, stockings or

ornamentation of any type should be placed on or

attached to the replace. This is a heating appliance. The

ow of heat can ignite combustibles.

Figure 1

GENERIC MODEL SHOWN

COMBUSTIBLE MATERIAL

TABLE OF CONTENTS

SECTION PAGE PAGE

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS 3-9

LIGHTING INSTRUCTIONS 10

MAINTENANCE AND SERVICE 11-12

IMPORTANT SAFETY INFORMATION 13

SAFETY INFORMATION FOR USERS OF LP GAS 14

REQUIREMENTS FOR MASSACHUSETTS 15

WARRANTY BACK COVER

37743-1-0117 Page 3

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

Technical Data

Remote Control

Supply voltage 4.5 V (three 1.5 V AAA batteries)

Ambient temperature ratings 0-50°C (32 - 122°F)

Radio frequency 315 MHz

WARNING

THE TRANSMITTER AND RECEIVER ARE RADIO FRE-

QUENCY DEVICES. PLACING THE RECEIVER IN OR NEAR

METAL MAY SEVERELY REDUCE THE SIGNAL RANGE.

WARNING

TURN “OFF” THE MAIN GAS SUPPLY AND ELECTRICAL

SUPPLY TO THE APPLIANCE DURING INSTALLATION AND/

OR MAINTENANCE OF THE RECEIVER DEVICE.

WARNING

FIRE HAZARD. CAN CAUSE SEVERE INJURY OR DEATH.

THE RECEIVER CAUSES IGNITION OF THE APPLIANCE.

THE APPLIANCE CAN TURN ON SUDDENLY. KEEP AWAY

FROM THE APPLIANCE BURNER WHEN OPERATING THE

REMOTE SYSTEM OR ACTIVATING MANUAL BYPASS OF

THE REMOTE SYSTEM.

CAUTION

PROPERTY DAMAGE HAZARD.

EXCESSIVE HEAT CAN CAUSE PROPERTY DAMAGE.

THE APPLIANCE CAN STAY LIT FOR MANY HOURS. TURN

OFF THE APPLIANCE IF IT IS NOT GOING TO BE ATTEND-

ED FOR ANY LENGTH OF TIME. ALWAYS PLACE THE

TRANSMITTER WHERE CHILDREN CAN NOT REACH IT.

Figure 2

Figure 3

NOTE: This control system includes a Battery Back-up pack that

allows the Fireplace to operate in the event of a power outage.

NOTE: The Accent Light and/or Blower features will not operate

during a power outage.

NOTE: Replace all Batteries at least once each year, preferably

before at the beginning of the season.

CAUTION

FIRE OR EXPLOSION HAZARD.

CAN CAUSE PROPERTY DAMAGE, SEVER INJURY OR

DEATH. DO NOT ATTEMPT TO TAKE APART THE GAS CON-

TROL OR TO CLEAN IT. IMPROPER ASSEMBLY AND CLEAN-

ING CAN CAUSE UNRELIABLE OPERATION.

37743-1-0117Page 4

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

Initializing the System for the First Time

1. Remove the wall cover. Remove cover on the wall mounted

battery back-up holder. See Figure 4. Install the four AA

batteries into the wall mounted battery back-up holder then

reinstall the cover. See Figure 5.

2. Install three AAA batteries into the battery bay located on the

base of the transmitter. See Figure 6.

3. Set the wall remote slide switch to the “REMOTE” position.

See Figure 5.

4. Press and release the SWI button on the wall control with

a paper clip and the IFC module will beep three times to

indicate the IFC module is ready to synchronize with the

transmitter within ten seconds. See Figure 5.

Figure 4

SWI

BUTTON

Figure 5

5. With the batteries already installed in the Transmitter, push

the On button. The Receiver will “beep” four times to indicate

the Transmitter’s command is accepted and sets to the par-

ticular code of that Transmitter. The system is now initialized.

Figure 6

Temperature Indication Display °C or °F

With the system in the “OFF” position, press the Thermostat

Button and the Mode Button at the same time. Look at the LCD

screen on the Transmitter to verify that a °C or °F is visible to the

right of the Room Temperature display. See Figures 7 and 8.

Figure 7

Figure 8

37743-1-0117 Page 5

Turn On the Appliance

With the system OFF, press the ON/OFF Button on the Transmit-

ter. The Transmitter display will show some other active Icons on

the screen. At the same time the Receiver will activate the appli-

ance. A single “beep” from the Receiver will conrm reception of

the command.

Turn OFF the Appliance

With the system ON, press the ON/OFF Button on the Trans-

mitter. The Transmitter LCD display will only show the room

temperature. See Figure 9. At the same time the Receiver will

turn off the appliance. A single “beep” from the Receiver conrms

reception of the command.

Remote Control Display - Figure 9

Remote Flame Control

The Proame has six ame levels. With the system on, and the

ame level at the maximum in the appliance, pressing the Down

Arrow Button once will reduce the ame height by one step until

the ame is turned off.

The Up Arrow Button will increase the ame height each time it

is pressed. If the Up Arrow Button is pressed while the system is

on but the ame is off, the ame will come on in the high position.

See Figures 10 through 13. A single “beep” will conrm recep-

tion of the command.

OFF

Flame Off - Figure 10

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

OFF

Flame Level 1 - Figure 11

OFF

Flame Level 5 - Figure 12

OFF

Flame Level Maximum - Figure 13

37743-1-0117Page 6

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

The Thermostat Feature may be disabled if desired.

With all three AAA type batteries installed:

1. Take out one AAA battery.

2. While re-inserting the AAA battery, Push and hold down the

thermostat button. This will disable the thermostat feature on

the transmitter.

Room Thermostat (Transmitter Operation)

The Remote Control can operate as a room thermostat. The

thermostat can be set to a desired temperature to control the

comfort level in a room. To activate this function, press the Ther-

mostat Button (Figure 3). The LCD display on the Transmitter

will change to show that the room thermostat is “ON” and the

set temperature is now displayed. See Figure 14. To adjust the

set temperature, press the Up or Down Arrow Buttons until the

desired set temperature is displayed on the LCD screen of the

Transmitter. See Figure 15.

SET TEMPERATURE

ROOM TEMPER ATURE

Figure 14

Figure 15

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the ame height in

accordance to the difference between the set point temperature

and the actual room temperatures. As the room temperature gets

closer to the set point the Smart Function will modulate the ame

down. To activate this function, press the Thermostat Button until

the word “SMART” appears to the right of the temperature bulb

graphic. See Figure 16. To adjust the set temperature, press the

Up or Down Arrow Buttons until the desired set temperature is

displayed on the LCD screen of the Transmitter. See Figure 17.

NOTE: When Smart Thermostat is activated, manual ame

height adjustment is disabled.

Figure 16

Figure 17

Blower Control (Fan)

If the appliance is equipped with a hot air circulating fan, the

speed of the fan can be controlled by the Proame system. The

fan speed can be adjusted through six speeds. To activate this

function, use the Mode Button (Figure 3) to index the fan control

icon. See Figure 18. Use the Up/Down Arrow Buttons (Figure

56) to turn on off or adjust the fan speed. See Figure 19. A single

“beep” will conrm reception of the command.

OFF

Figure 18

OFF

Figure 19

37743-1-0117 Page 7

Remote Dimmer Control (Light)

The auxiliary function controls the AUX power outlet by the dim-

mable light control. To activate this function, use the Mode Button

(Figure 3) to index to the AUX icon. See Figures 20 and 21.

The intensity of the output can be adjusted through six levels.

Use the Up/Down Arrow Buttons (Figure 3) to adjust the output

level. A single “beep” will conrm reception of the command.

Note: This function is available only with the IFC control Module.

OFF

Figure 20

OFF

Figure 21

Split Flow Control

The secondary burner is controlled by the split Flow. To activate

this function use the Mode Button (Figure 3) to index to the

SPLIT FLOW mode icon. See Figures 22 and 23.

Pressing the Up Arrow Button will activate the secondary burner.

Pressing the Down Arrow Button will turn the secondary burner

off. A single “beep” will conrm the reception of the command.

OFF

Figure 22

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

OFF

Figure 23

Remote Auxiliary Relay Control (optional with this replace)

The auxiliary function controls the AUX relay outlet. To activate

this function use the Mode Button (Figure 3) to index to the AUX

icon (Figures 24 & 25). Pressing the Up Arrow Button will acti-

vate the outlet. Pressing the Down Arrow Button will turn the out-

let off. A single “beep” will conrm the reception of the command.

Figure 24

Figure 25

37743-1-0117Page 8

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

Continuous Pilot/Intermittent Pilot (CPI/IPI) Selection

With the system in “OFF” position press the Mode Button

(Figure 3) to index to the CPI mode icon. See Figures 26

and 27. Pressing the Up Arrow Button will activate the CPI.

Pressing the Down Arrow Button will return to IPI. A single “beep”

will conrm the reception of the command.

OFF

Figure 26

OFF

Figure 27

Button Lock

his function will lock the Buttons to avoid unsupervised operation.

To ac

tivate this function, press the MODE and UP Buttons at the

same time. See Figure 28.

To deactivate this function, press the MODE and UP Buttons at

the same time.

OFF

Figure 28

Low Battery Power Detection - Transmitter

The life span of the remote control batteries depends on various

factors: quality of the batteries used, the number of ignitions of

the appliance, the number of changes to the room thermostat set

point, etc.

When the transmitter batteries are low, an Icon will appear on the

LCD display of the transmitter See Figure 29 before all battery pow-

er is lost. When the batteries are replaced this Icon will disappear.

OFF

Figure 29

37743-1-0117 Page 9

Lockout State Denition

A lockout state is reached when an ignition error occurs. The

lockout state will remain set in memory as long as the power

supplies are applied.

This could mean both an irregular ame detection and/or too

many unsuccessful ignition attempts.

This state is a safe condition for the appliance and is entered

automatically by the IFC board.

When the IFC board gets into lockout state:

1. both the Pilot and the Main Burner solenoids in the gas valve

are de-energized;

2. a diagnostic code is sent through the diagnostic red LED.

3. the IFC board will ignore any burner ignition command and

remain in the OFF state unless the unlock command se-

quence is met.

The causes of lockout must be investigated under safe conditions

by the user and/or the service personnel.

To reset the IFC from a lockout state, perform the following pro-

cedure:

Turning the system power supplies (to the wall control or

remote control) OFF for two or three seconds and then

restoring a power supply back on.

The return of the system to normal operation must be checked

under safe conditions by the user and/or service personnel.

Using the Fireplace without a Remote Control

The replace can be turned ON (HI only) and OFF with the wall

switch. The replace ame ON/OFF is the only function that will

operate; no ame adjustment, light or blower will work when us-

ing the wall switch. The wall control switch should be turned OFF

when the replace is not being used for extended periods of time.

Battery Backup Operation

Install batteries (See initialization sequence on page 44). In case

of power loss, the replace will switch to battery mode automat-

ically. The replace will operate normally without the fan or light

control when in battery mode.

Low Battery Detection

When the backup batteries are low, a double-beep will be emitted

when the module receives an on/off command. No commands

will be accepted until the batteries are replaced or the A/C power

is restored.

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

37743-1-0117Page 10

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR

EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR

LOSS OF LIFE.

A. This appliance must be lighted with the remote control.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell around the appliance area for

gas. Be sure to smell next to the oor because some

gases are heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions. If you can not reach your gas

supplier, call the re department.

C. Use only the remote control to operate the valve. Never

use tools. If valve does not operate, don't try to repair it,

call a qualied service technician. Force or attempted

repair may result in a re or explosion.

D. Do not use this appliance if any part has been underwater.

Immediately call a qualied service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been underwater.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is to

be performed (if applicable).

2. Locate On/Off gas shutoff knob and turn clockwise to

"OFF." Do not force.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Turn OFF electric power to the appliance.

3. Turn gas shutoff knob counterclockwise to

"ON" position.

4. Wait ten minutes to clear out any gas. Then smell for gas,

including near the oor. If you smell gas, STOP! Follow

"B" in the safety information above on this label. If you

do not smell gas, go to the next step.

5. Turn ON electric power to the appliance.

6. Using the remote control, turn main ame to "ON." Refer

to the Multifunction Remote Operating Instructions for

more information. If the pilot does not light within 60

seconds, stop and go back to Step 4.

7. Refer to remote control instructions for detailed

information, control features, and operation. Note:

Refer to Multifunction Remote operating instructions

for selection of continuous standing pilot mode or

intermittent pilot mode. If the pilot or burner does not stay

lit (in the standing pilot mode), stop and immediately call

a qualied service technician or gas supplier.

8. If the burner or pilot does not operate properly after

several tries, turn the gas shutoff knob clockwise

to "OFF" and call your service technician or

gas supplier.

9. Operation of the gas valve, blower, and/or optional light

must be controlled by using the hand held remote control.

Refer to remote instructions for detailed operation

information.

IGNITOR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Empire Kamin im Innenbereich Handbücher

Empire

Empire MANTIS BF28 Series Bedienungsanleitung

Empire

Empire OP32FB2MF-3 Kurzanleitung

Empire

Empire DVCT30 Bedienungsanleitung

Empire

Empire DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N Bedienungsanleitung

Empire

Empire DVCT36CFP95-1 Bedienungsanleitung

Empire

Empire DVCC BP3 Series Bedienungsanleitung

Empire

Empire OLP36FP72S(N Kurzanleitung

Empire

Empire LS30TINF Kurzanleitung

Empire

Empire B Vent Zero Clearance Betriebsanleitung

Empire

Empire VFLL38FP(3 Kurzanleitung

Empire

Empire BP28(B Bedienungsanleitung

Empire

Empire DVCC32BP32N-1 Kurzanleitung

Empire

Empire DVCT36-CF Bedienungsanleitung

Empire

Empire B3RSTHK18N Kurzanleitung

Empire

Empire DVCD42FP31P-2 Kurzanleitung

Empire

Empire DVCC32BP30N-2 Kurzanleitung

Empire

Empire VFD(10 Kurzanleitung

Empire

Empire DVCT50CBP95-1 Bedienungsanleitung

Empire

Empire VFRL1810N Kurzanleitung

Empire

Empire MILLIVOLT DVCDFP30-1 Series Kurzanleitung

Empire

Empire LFR(18 Bedienungsanleitung

Empire

Empire Mantis BF28BM-5 Bedienungsanleitung

Empire

Empire OP32FB2MF-4 Kurzanleitung

Empire

Empire DVCP32BP30N-4 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch