Emprex 3009ARF III Bedienungsanleitung

Wireless Remote controller

3009ARF III

EMPREX,BTC

FCC GUIDELINES

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Use only shielded cables to connect I/O devices to this equipment.

FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, (2) this device must

accept any interference received, including interference that may cause undesired operation.

Information to user: The users manual or instruction manual for an intentional or unintentional

radiator shall caution the user that changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment. Shielded interface cable, if

any, must be used in order to comply with emission limits.

Do not litter

低功率電波輻射性電機管理辦法:

第十二條：經型式認證合格之低功射頻電機，非經

許可，公司、商號或使用者均得擅自變頻、加大

功或變原設計之特性及功能。第十四條：低功射

頻電機之使用得影響飛航安全及干擾合法通信；經

發現有干擾現象時，應即停用，並改善至無干擾時

方得繼續使用。前項合法通信，指依電信法規定作

業之無線電信。低功射頻電機需忍受合法通信或工

業、科學及醫用電波射性電機設備之干擾。

Table of Contents

Getting Started ......................................................2

What’s in the Package ...........................................2

System Requirements............................................2

Hardware Installation............................................2

ID Pairing Information ..........................................3

RemoteMaestro installation ...................................4

Remote Button Functions.......................................5

1.Power Button......................................................6

2.Transport Control Buttons ..................................6

3.Navigation Control Buttons.................................7

4.Audio and Video Control Buttons ........................7

5.Media Center Shortcut Buttons ...........................8

6.Numeric Keypad..................................................8

7.Teletext Control Buttons.....................................9

Troubleshooting...................................................9

3009ARF III Remote Control

Getting Started

The remote control is for Media Center PC with up to 6 months of battery life, 10-meter

range of operable distance (varied depending on the environment), and access to

various media experiences. The plug-and-play 2.4GHz remote control is the total

solution for all of your remote control requirements. Just plug the receiver into the USB

port of your Media Center PC and start to enjoy the complete wireless freedom of a

whole new home entertainment experience.

What’s in the Package

1. Remote Control

2. Dongle Receiver

3. Battery (Two AAA alkaline batteries included in the package)

4. Quick Installation Guide

5. CD disc

System Requirements

1. Available USB port

2. Windows® Media Center PC or other peripheral devices with Windows® Media

Center

3. CD-ROM drive (for CD and Video operation)

Hardware Installation

Receiver Installation

Plug the USB connector directly into an available USB port on your computer.

Note:

For optimum performance, keep a direct unobstructed line of sight between the receiver

and the remote control.

Battery Installation

1. Slide open the battery compartment cover and insert two AAA

batteries.

2. To ensure that the batteries are installed correctly, follow the

polarity signs in the battery compartment.

3. Replace the battery compartment cover.

Notes on Batteries:

1. The device uses 2pcs standard UM-4 (AAA) 1.5V alkaline batteries. We recommend

using alkaline batteries for a longer battery life.

2. Battery life is up to 6 months, depending on the intensity of usage.

3. Do not combine alkaline batteries with another type of battery. Also do not combine

fresh batteries with used batteries. Always replace used batteries with fresh batteries of

the same type.

4. Remove the batteries after long periods of non-use. Battery leakage or movement may

damage the device, and may also be unsafe to handle.

3009ARF III Remote Control

ID Pairing Information

The remote control is ready for use as soon as you take it out of the box and plug

the receiver USB connector into a USB port on your computer. If it does not work,

you must configure the ID setting of the remote control, as described below.

The position of ID/connect button is respectively located on the top of the dongle receiver

and back of the remote control. An LED indicator under the receiver ID/connect button

shows the pairing or data reception status.

1. Press and hold the ID/connect button on the receiver for at least 2 seconds, until the

LED indicator on the receiver flashes. (If you release the button within 2 seconds, the

ID pairing will fail.)

2. Hold the remote control within 30 cm of the dongle receiver. (Hold the remote control

close to the receiver within 30 cm.)

3. Press and hold the connect button on the bottom of the remote control for at least 2

seconds, until the LED indicator on the receiver stops flashing. (If you release the

button within 2 seconds, the ID pairing will fail.)

4. You can now begin using the remote control.

Connect Button

(With an LED indicator underneath)

NOTES:

1. Your computer must be turned on before you can perform this pairing procedure.

2. You must follow this procedure in order to complete ID pairing.

3. Each procedure should be completed within 60 seconds.

4. You do not need to pair IDs again after changing the batteries in the remote control. If

the remote control does not work properly, please follow the ID pairing procedure

above to configure the ID again.

3009ARF III Remote Control

RemoteMaestro installation

To input the text, please follow the process as below to install the “3009ARF

3_triple-tap reg” file to access the function of text button of remote control in

Windows Media Center.

1. Insert the CD labeled “RemoteMaestro” into your CD-ROM drive. And follow the on

screen instruction to install.

2. Double click “3009ARF III_triple-tap reg”, and the dialog box “Windows need your

permission continue” pops up. To continue the next step, please click “Continue”.

3. Then, the “Registry Editor” dialog box will pop up to ask you if you want to continue

the registry. Click “Yes” to continue.

4. Click “OK” to complete the registry.

3009ARF III Remote Control

Remote Button Functions

The remote control has one power button and six types of buttons for entering

commands. Just connect the receiver with the USB port, point the remote control at the

receiver, and you can start to access and manage your Media Center PC or other

peripheral devices. No software or setup procedure is required!

3009ARF III Remote Control

1. Power Button

Button Control Task

Power

(Standby)

Put the equipment in standby mode, depending on the

power management setting of the system.

2. Transport Control Buttons

Transport control buttons allow you to control the media.

Button Control Task

Play Play the selected media.

Pause Pause the currently playing media. Press Pause again

to resume.

Stop Stop the currently playing media.

Record Record what you are currently watching to the disk.

Rewind

Rewind the currently playing media. If pressed

repeatedly, cycles through three rewind speeds from

slowest to fastest.

Note: Rewind only support Video system.

(It will be unavailable on Audio system.)

Fast Forward

Speed up the currently playing media. If pressed

repeatedly, cycles through three fast forward speeds

from slowest to fastest.

Note: Fast Forward only supports Video system.

(It cannot work on Audio system.)

Skip Backward

Skip to the previously playing media.

Skip Forward Skip to the next playing media.

3009ARF III Remote Control

3. Navigation Control Buttons

Navigation control buttons allow you to move between items on the screen.

Button Control Task

Green Start Button

(MCE) Open the Media Center Start menu.

Back Go to the previous screen.

More Display information about the selected

item.

Cursor Keys Move the cursor upward, downward, to the

left, or to the right in a program guide or in

menu screens.

OK Select the highlighted option.

4. Audio and Video Control Buttons

Audio and video control buttons allow you adjust volume and change channels.

Button Control Task

Volume Up Adjust the volume up.

Volume Down Adjust the volume down.

Mute Turn the sound off. Press Mute again to resume.

Ch Up Select the next higher channel.

Ch Down Select the next lower channel.

3009ARF III Remote Control

5. Media Center Shortcut Buttons

Media Center shortcut buttons allow you access various media experiences.

Button Control Task

Recorded TV Bring up the Recorded TV page.

Guide Bring up the electronic programming guide.

Live TV Show live TV on the currently selected channel.

DVD Menu Display the DVD menu.

Music Display the Music Library.

Pictures Display the Picture Library.

Videos Display the Video Library.

Radio Bring up the main Radio page.

6. Numeric Keypad

Numeric keypad is for entering alphanumeric characters or TV channels.

Button Task

0-9 For entering text and TV channels.

* Insert a * symbol, if supported by the selected device.

# Insert a #symbol, if supported by the selected device.

Clear (ESC) Clear the setting / Exit the setting.

Enter Select the highlighted option.

Inhaltsverzeichnis

Andere Emprex Fernbedienung Handbücher

Emprex

Emprex M961U Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung