EMS FIRECELL Installations- und Betriebshandbuch

Survey Kit

Verication Guide

Introduction

The procedure described in this document is a verication of performance and not a

calibration. Calibration requires complex equipment to conduct measurements which due

to the nature of the site survey equipment is not required. The verication will conrm

continued performance of the survey kit such that it is suitable for continued use without the

cost of formal calibration.

There are two sections outlined within this document:

Section 1 - General maintenance (pages 3 to 4)

Section 2 - Two yearly maintenance (pages 5 to 6)

If you encounter issues completing the steps outlined in this document, please contact EMS

technical support.

Kit familiarisation

SURVEYOR

DEVICE

LOCAL - REMOTE PASS / FAIL

SIGNAL QUALITY % REMOTE - LOCAL

BATTERY

Pole Mounted

Survey Tool

CH 1 CH 2 CH 1 CH 2

POWER/

CHARGE

RSSI/dB

START

LOCAL - REMOTE REMOTE - LOCAL

Signal Surveyor Device survey

rods

12 VOLT

BATTERY

CHARGER

Signal Surveyor

mains charger

Page 2 of 8

Specied batteries

When replacing batteries; observe correct polarity, using only specied batteries shown

below.

Note: Fitting of an incorrect battery type invalidates the product certication and may result

in poor performance.

Signal Surveyor: 1 x 6V 4Ah Lead Acid battery

(Yuasa NP4-6)

Pole Mounted Survey Tool: 4x AA Alkaline batteries

(Panasonic LR6AD Powerline / Varta 4006 Industrial)

Page 3 of 8

Section 1

General maintenance

Page 4 of 8

Charge the Signal Surveyor

Charge the Signal Surveyor (with the

left-hand side power switch o). The

unit’s ‘POWER/CHARGE’ LED will

illuminate amber whilst charging and

will extinguish once fully charged.

Replace the battery if it does not

fully charge within 24 hours. See

the ‘Battery specication’

section.

Quick range test

Full signal should be achievable at 40m distance in open air.

CH 1 CH 2 CH 1 CH 2

POWER/

CHARGE

RSSI/dB

START

LOCAL - REMOTE REMOTE - LOCAL

SURVEYOR

DEVICE

LOCAL - REMOTE PASS / FAIL

SIGNAL QUALITY % REMOTE - LOCAL

BATTERY

Setting up comms

Surveyor Vxx.xx

Power up the kit

Switch on both units as shown.

The Pole Mounted Survey Tool will

go into power save mode (screen

o) when not in use.

If however it doesn’t start up,

replace all four batteries. See the

‘Battery specication’ section.

SURVEYOR

DEVICE

LOCAL - REMOTE PASS / FAIL

SIGNAL QUALITY % REMOTE - LOCAL

BATTERY

>45dB >45dB Pass

BG = 0dB

CH 1 CH 2 CH 1 CH 2

POWER/

CHARGE

RSSI/dB

START

LOCAL- REMOTE REMOTE- LOCAL

SURVEYOR

DEVICE

LOCAL- REMOTE PASS/FAIL

SIGNALQUALITY % REMOTE- LOCAL

BATTERY

Page 5 of 8

Section 2

Two yearly maintenance

Page 6 of 8

Two yearly test

Replace all batteries every two years, observing

correct polarity and using only specied batteries.

See the ‘Specied batteries’ section.

Replace all batteries

It is recommend that the The Signal Surveyor’s

Mains Charger is routinely checked every two years

for electrical safety, in accordance with any local

codes of practice. I.e. PAT testing in the UK.

Mains charger test

PASSED

ELECTRICAL SAFETY TEST

App ID:

Tested:

Re-test:

Engineer:

868

05/02/18

05/02/20

P. Smith

Change all batteries

Quick range test

Mains charger test

Page 7 of 8

Range Test Bench Mark Form

Site Location Details

Survey Date Background Level Distance Signal Level Comments

dB %

www.emsgroup.co.uk

Third Party Accredited

ISO 9001 ISO 14001

The information contained within this literature is correct at time of publishing. The EMS Security Group Ltd reserves the right to change any information regarding products as

part of its continual development enhancing new technology and reliability. The EMS Group advises that any product literature issue numbers are checked with its head oce

prior to any formal specication being written.

Page 8 of 8

Andere Handbücher für FIRECELL

Andere EMS Prüfgeräte Handbücher