EMX Industries, Inc. PC-3 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S

Operating Instructions

4564 Johnston Parkway, Cleveland, Ohio 44128

P. 800 426 9912 F. 216 518 9884

Sales Inquiries: [email protected]

Technical Support: [email protected]

www.emxinc.com

PC-3™

THRU BEAM PHOTOEYE

U L 3 2 5 N O N - C O M PL I A N T

PC-3™ Operating Instructions Rev 1.4 1

Document no.

Contents

Cautions and Warnings

Product Overview

Specifications

Connections

Troubleshooting

Ordering Information

PC-3™ Operating Instructions Rev 1.4 2

Document no.

Cautions and Warnings

WARNING … Not to be used for Personnel Protection

Never use product as sensing devices for personnel protection. Doing so could cause serious

injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in

personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition. UL 325 Non-compliant

Product Overview

The PC-3 photoeye system does not have a focusing lens and the generous 24osensing angle makes it

one of the easiest to align. Do not use outdoors or where there is chance of getting wet.

Specifications

Power Supply

12-24 VDC 24 VAC

Power Supply Tolerance

+/- 20%

Current Draw

Tx: 37mA Rx:23mA Standby, 17mA Detect

Housing Material

PVC Black

Relay Type

Form C DPST contact rating 1A@24VDC/120VAC

Temperature Range

-40Fº -170Fº

Connections

Tx: 18in 2 Conductor RX: 18 in 5 Conductor

Detect Indicator

Red LED

Power Protection

Thermal Fuse

Environmental

IP50 Not water tight

Range

30 Feet

Response Time

10mS (max.)

Size

4in. x 2in. x 1.5 in.

Detection Angle

24º

PC-3™ Operating Instructions Rev 1.4 3

Document no.

PC-3 Transmitter connections (figure 1)

1. Connect power Red (+) positive

2. Connect power Black (-) negative

Not polarity sensitive

PC-3 Receiver connections (figure 2)

1. Connect power to Red (+) positive

2. Connect power to Black (-) negative

3. Connect White internal relay common to

operator input Common or Gnd as specified

by operator manual

4. Connect Green internal relay normally open to

operator input open, safety reverse or other

as specified by operator manual

5. The Brown internal relay normally closed is

not normally used and may be just cut off or

left alone

6. The detect Led will glow red when an

obstruction occurs.

Connections

Transmitter

Receiver

Red Wire

Power Positive (+)

Black Wire

Power Negative(-)

White Wire

Internal Relay Common Output

Brown Wire

Internal Relay Normally Closed Output

Green Wire

Internal Relay Normally Open Output

Power is not polarity sensitive

Detect LED

Figure 1 Figure 2

PC-3™ Operating Instructions Rev 1.4 4

Document no.

Troubleshooting

Symptom

Possible cause

Solution

Holds gate open

No power on Tx or Rx

Check power source, Check detect LED

Does not activate gate

Bad connection or

broken wires

Relay Contacts

burned or stuck

Not connected to

correct input

terminals

Sunlight “blinding”

the receiver eye

Check wires and connections

Replace receiver

Check operator manual for terminals

Change position of receiver to shield

the sensor from the direct sunlight

Chattering

Interference or stray

bounced signal

See if any reflective surfaces could be

sending signal into the receiver sensor

Ordering Information

PC-3 PC-3 Transmitter and Receiver

Accessories

IRB-BR Set of 2 L Mounting Brackets

PC-3™ Operating Instructions Rev 1.4 5

Document no.

Warranty

EMX Industries Incorporated warrants all products to be free of defects in

materials and workmanship for a period of two years under normal use and

service from the date of sale to our customer. This warranty does not cover

normal wear and tear, abuse, misuse, overloading, altered products, damage

caused by incorrect connections, lightning damage, or use other than intended

design.

There is no warranty of merchantability. There are no warranties expressed or

implied or any affirmation of fact or representation except as set forth herein.

EMX Industries Inc. sole responsibility and liability, and the purchaser’s

exclusive remedy shall be limited to the repair or replacement at EMX

Industries option of a part or parts found not conforming to the warranty. In

no event shall EMX Industries Inc. be liable for damages, including but not

limited to damages resulting from non-conformity, defect in material or

workmanship.

Effective date: January 1st, 2002

PC-3™ Operating Instructions Rev 1.4 6

Document no.

4564 Johnston Parkway

Cleveland, Ohio 44128

United States of America

www.emxinc.com

Technical Support: (216) 834-0761

[email protected]

Sales: (216) 518-9888

Fax: (216) 518-9884

[email protected]

Revision 1.4

7.13.2018

Inhaltsverzeichnis

Andere EMX Industries, Inc. Sicherheitssystem Handbücher

EMX Industries, Inc.

EMX Industries, Inc. Hawk 1 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung