Encelium KX3 Touchscreen Bedienungsanleitung

KX3 Touchscreen INSTALLATION INSTRUCTIONS

PRODUCT SAFETY

When using electrical equipment, basic safety precautions should always be followed, including the following:

Do not let power supply cords touch hot surfaces.

Do not mount near gas or electric heaters.

Do not use the unit near water.

Do not allow objects to fall or liquids to be spilled

into the enclosure through openings.

Equipment should be mounted in locations and at

heights where it will not readily be subjected to

tampering by unauthorized personnel.

The use of accessory equipment is not recommended

by Encelium as it may cause an unsafe condition.

Do not use this equipment for other than the

intended use.

SAVE THESE INSTRUCTIONS.

READ THESE INSTRUCTIONS BEFORE USING THIS PRODUCT.

GETTING STARTED

Overview

The Encelium KX3 Touchscreen Panel is a 89 mm (3.5 inches) flush-mount LCD touchscreen display that provides the ability to

recall multiple lighting scenes for a given zone. It's ideal for large multi-purpose spaces where lighting requirements vary

throughout the day, such as an auditorium or conference room.

2KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

SYSTEM OVERVIEW

Wired System Overview

With Encelium X, you can control DALI devices exclusively or a mixture of GreenBus and DALI.

GreenBus

Controller Wired Manager — GreenBus

Sensor SSU

Controller

Sensor

KX3 Touchscreen

Ethernet

GreenBus

Dimming

PoE

Wire Key

DALI

Wired Manager — DALI SSU

KX3 Touchscreen

Ethernet

DALI

PoE

Wire Key

Sensor Sensor

KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

Wireless System Overview

This illustration shows how each component is easily integrated into the Encelium X Lighting Control System.

Wireless Manager SSU

Sensor

sor

Sensor

KX3 Touchscreen

Integrated

Controller

Ethernet

PoE

Wire Key

4KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

MOUNTING OPTION

The KX3 Touchscreen is designed for flush-mount, in-wall installations. It requires an available mounting depth of 52.5 mm

(2 inches) from the surface of the wall. The recommended mounting height for the KX3 Touchscreen is between 1.4 and 1.5 m

(4.5 and 5 ft) from the bottom of the faceplate.

KX3 front

(bezel removed)

Bezel

74.7 mm

(2.9 inch)

131.8 mm

(5.2 inch)

Wall Stud

Wall

Opening

Ethernet Cable

(from PoE Switch)

Mouting Height

1.4 — 1.5 m

(4.5 — 5 ft )

from bottom

of faceplate

Note: There is little margin for error when fitting the KX3 Touchscreen into the wall opening. Make sure to use the included

cardboard cut-out template to create the correct size opening in the wall. Additionally, carefully double-check that all

measurements taken using the cardboard cut-out template are accurate.

KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

INSTALLATION

The KX3 Touchscreen shall be installed in dry, indoor locations ONLY.

Front View Rear View

CONTROL ETHERNETRS-232 (2)RS-232 (1)

The KX3 Touchscreen has the following built-in components: ambient and proximity sensors and reset button.

Reset Button

Ambient and

Proximity Sensors

6KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

ELECTRICAL CONNECTIONS

KX3 Touchscreen Wiring Diagram

GreenBus

To Additional Wired Managers

(As Needed)

Power Supply

100 — 240 VAC,

50/60 Hz, 1.8A

SSU

External PoE Switch

120 VAC, 60 Hz, 10 W

(Non-Emergency Circuit)

120 VAC, 60 Hz, 300 W

Emergency Circuit (Preferred)

Non-Emergency Circuit (Acceptable)

Ethernet Cable with PoE

91.4 m (300 ft) maximum (Typical)

Ethernet Cable

91.4 m (300 ft) maximum

(Typical)

Wired Manager —

GreenBus

To secure LAN Port for

PC Lighting Control

(Requires Static IP Address)

Note: The maximum run from the network switch

to any end device is 91.4 m (300 ft). The PoE Injector

does not extend the length limitation.

KX3

Note: A PoE Switch can be used. This will eliminate

the need for individual PoE Injectors.

CONTROL

DALI

To Additional Wired Managers

(As Needed)

Power Supply

100 to 240 VAC,

50/60 Hz, 1.3A

SSU

External PoE Switch

230 VAC, 50 Hz, 10 W

(Non-Emergency Circuit)

230 VAC, 50 Hz, 300 W

Emergency Circuit (Preferred)

Non-Emergency Circuit (Acceptable)

Ethernet Cable with PoE

91.4 m (300 ft) maximum (Typical)

Ethernet Cable

91.4 m (300 ft) maximum

(Typical)

Wired Manager — DALI

To secure LAN Port

for PC Lighting

Control (Requires

Static IP Address)

Note: The maximum run from the network switch

to any end device is 91.4 m (300 ft). The PoE Injector

does not extend the length limitation.

KX3

Note: A PoE Switch can be used. This will eliminate

the need for individual PoE Injectors.

CONTROL

Power

Supply

KX3 Touchscreen Installation Instructions

KX3 Touchscreen INSTALLATION INSTRUCTIONS

Ethernet Port Wiring

The Ethernet (LAN) connection enables communication with a control system and power-over-Ethernet (PoE). When

powering the KX3 using PoE, a 802.3af Compliant class 3 PoE switch must be used.

CONTROL ETHERNETRS-232 (2)RS-232 (1)

BUTTON KEYCAP REPLACEMENT

The KX3 Touchscreen hard button keycaps are compatible with the Laser Shark custom button etching service.

REMOVING BUTTON KEYCAPS

Remove the KX3 bezel.

encelium.com

Lumens logo, We Generate Facility Wellness, SiteWorx, LightRules, Lightelligence, Encelium,

the Encelium logo, Polaris, GreenBus and any other trademark, service mark, or tradename

(collectively “the Marks”) are either trademarks or registered trademarks of Digital Lumens,

Inc. in the United States and/or other countries, or remain the property of their respective

owners that have granted Digital Lumens, Inc. the right and license to use such Marks and/or

are used herein as nominative fair use. Due to continuous improvements and innovations,

specifications may change without notice.

DOC-000446-00 Rev C 02-22

KX3 Touchscreen INSTALLATION INSTRUCTIONS

Using your fingernail or small screwdriver, gently pry up on the bottom edge of the keycap.

Button

Pry up here to

remove button

INSTALLING BUTTON KEYCAPS

Align the keycap directly over the button location.

Gently press straight down on the keycap until it is seated flush with the display.

TROUBLESHOOTING

There are no user-serviceable parts inside. For detailed information about how to set-up, install, use, and maintain Encelium

hardware and software, please visit: help.encelium.com

Inhaltsverzeichnis

Andere Encelium Touch-Screen Handbücher

Encelium

Encelium KX7S Bedienungsanleitung

Beliebte Touch-Screen Handbücher anderer Marken

Elecro Engineering

Elecro Engineering Poolsmart Plus Montageanleitung

Johnson Controls

Johnson Controls IQ4 HUB Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET2270L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET1002L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems 3201L Bedienungsanleitung

Duratec

Duratec S15 Bedienungsanleitung

Crestron

Crestron TPMC-3SM Bedienungsanleitung

Racelogic

Racelogic MFD Touch Bedienungsanleitung

J2 580 Benutzerhandbuch

HAI

HAI OmniTouch 10p Bedienungsanleitung

panel

panel PC PSR108-FM Series Bedienungsanleitung

Tipro

Tipro FREE+ Bedienungsanleitung

Systemline

Systemline Commander Bedienungsanleitung

Interactive Technologies

Interactive Technologies Insite Bedienungsanleitung

GVision

GVision Legacy Bedienungsanleitung

BeiJer

BeiJer T21C-C24 Bedienungsanleitung

Advantech

Advantech ITM-5117 Series Bedienungsanleitung

Edge

Edge CS Bedienungsanleitung