WORK SITE SET UP
TROUBLESHOOTING for the 2800/2500
SAFETY CAUSE SOLUTION
Blade does not return Sticky main valve Lubricate main valve and check that
main valve piston moves
Loose screw in housing cap Tighten all 4 screws in cap
Sluggish tool Dry main valve Lubricate main valve
Clips not feeding Obstruction in magazine Remove obstruction
Clips caught in track Inspect track, manually dislodge clips
Loose clips Low air pressure Increase pressure to 80 psi
Worn blade or anvil Replace blade or anvil
Wrong clips for application Review E-Clips Guide, By Tool, available
at encorehartco.com/support
Clip jamming Wrong size of clips loaded, Slide red auxiliary air valve to the side
or clip misaligned in to relieve pressure, loosening clip
chamber
Tool not cycling Clogged trigger valve Clean trigger valve assembly
Obstruction in chamber Slide red auxiliary air valve to the
side to loosen obstruction
5
CC SYSTEM PARTS
EA/HR 2800 Eclipser 2800-XXXX (unique for each system)* 1
EA/HR 2500 Eclipser 2500-XXXX (unique for each system)*
*2800 or 2500 ECLIPSER TOOL #s (for each system)
“A” -13320, -13321, -13322, or -13324
“F-H” -6082, -6181, or 6185
30180 – CC SYSTEM FRAME “A”
30123 Clip Track Assembly “A” 1
20020 SHCS, 8-32 x 1/4” 28
20021 Hex Nut, 8-32 Thin Ht 24
30121 Clip Track “A” 1
30122 Clip Track Guide “A” 14
30190 – CC SYSTEM FRAME “E-F-H”
30157 Clip Track Assembly “E-F-H” 1
20020 SHCS, 8-32 x 1/4“ 28
20021 Hex Nut, 8-32 Thin Ht 24
30155 Clip Track “F-H” 1
30156 Clip Track Guide “E-F-H” 14
UNIVERSAL PARTS for CC SYSTEM FRAMES
15100 Nut, 3/8”-16 Hex 4
15240 Washer, 3/8” 1
15256 Washer, 3/8” Locking 4
15598 SHCS, 3/8”-16 x 3/4” 1
15624 SHCS, 1/4”-28 x 3/4” 2
20028 Push-In Straight Fitting, 1/4” NPT 3/8”Tube 1
20054 3/8” Lubricator 1
20055 3/8” Regulator 1
20056 Tool Balancer 1
20057 Collar, Single Split 1/2” 2
20058 Close Nipple, 3/8” NPT 1
20060 Eye Hook, 3/8“-16 1
20063 Coil Hose Assembly 1
20167 Push-In 90° Ftg, 3/8”NPT x 3/8“ Tube 1
20168 Carriage Rod 1
20170 3/8” Air Hose 1
20171 Coupler Body, 1/4” NPT x 1/4” Female 1
20172 HHCS, 3/8”-16 x 2-3/4” 4
20173 Nut, 3/8”-16 Hex Nylock 2
20177 1/4” NPT Female 90° Elbow Ftg 1
30158 Spool Support Rod 1
30159 Carriage Assembly Parts 1
15150 1/2” Linear Bushing 1
20169 Internal Retaining Ring 2
65157 Block, Track Carriage 1
30164 Upright Weldment 1
30165 Upper Weldment 1
30170 Base Weldment 1
Item # Description Qty
Encore Hartco Continuous
Coil (CC) Clipping System
Encore Hartco’s complete stand-alone system has two major
components: 1) an assembly that includes a heavy duty
frame, spool rod, clip track, rod and track carriage system,
tool balancer, hose, and air regulator; and 2) an Encore Hartco
Eclipser 2500 or 2800 Series clipping tool. Each component is
made to suit specic applications and is ordered separately. For
the CC System (the frame and a tool), the customer provides:
• a3/8”NPTairinlettting
• compressedair(3.5SCFMat80-90psi)
• asuitablerollofclinchclips
REQUIRED COMPONENTS
The Eclipser 2500 and 2800 series tools are designed to install clips from a
continuous roll or coil. For proper operation of the Eclipser, the following
additional components will be required:
• acompressedairsource;
• acliptrack(P);
• arodandtrackcarriagesystem(Q) to guide clips, left to right and
back again, as they unspool from the roll into the clip track;
• aheavydutyhorizontalrod(R) on which
to place the roll of clips,
at an elevation of
approximately 5 feet;
and
• arollofclips(S)
suitable for your
application
and tool.
5’
RQ
P
S
6-29-2021 © 2021 Encore Hartco
Eclipser 2500-2800 Man v0629 BW.indd 5 6/29/21 3:42 PM
