Ender 3 S1 Installationsanleitung
Ender-3 S1 FAQ
Issue about installation
1How long does it take to assemble the
machine?
Here is our suggestion for you problem:
Ender-3 s1 product is 96% pre-assembled.
Generally, the printer can be assembled in 5-20 minutes.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
2Where is the consumables rack mounted
to?
Here is our suggestion for you problem:
The consumables rack is fixed to the top of the gantry.
It is placed vertically on top and secured with screws.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
3What about the nozzle kit shaking
after the machine is installed?
Here is our suggestion for you problem:
Please tighten the eccentric nut on the back plate of the nozzle kit.
After commissioning you can test by sliding it from side to side.
Tight is stuck, loose is shaky
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
4Why is the platform a little shaky
after the machine is installed?
Here is our suggestion for you problem:
Please adjust the eccentric nut at the V-wheel of the hot bed.
After commissioning you can test by sliding it
Tight is stuck, loose is shaky
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
5What about the Z-axis movement lag
after the machine is installed?
Here is our suggestion for you problem:
Once the screw is installed, the screw nut needs to be adjusted
The axis of movement up and down needs to be the same to maintain a smooth movement.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
6
What about the X-axis movement get
stuck, after the machine is installed
or left for a period of time?
Here is our suggestion for you problem:
Please check that the V-wheel is not stuck,
Then adjust the V-wheel until it moves smoothly.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
7Do Z-axis limit switches need to be
installed?
Here is our suggestion for you problem:
The dimensions of the printed model of this printer are: length/width/height 220*220*270
mm
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
Issue about basic parameter
8 What is the print size?
Here is our suggestion for you problem:
The dimensions of the printed model of this printer are: length/width/height 220*220*270
mm
We hope this helps you.
If you need further assistance with this issue, you can always contact us
9Does this machine support two-color
printing?
Here is our suggestion for you problem:
Sorry, this printer is a single printhead construction and does not support two-colour
printing
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
10 What is the printing precision of the
machine?
Here is our suggestion for you problem:
The printer comes standard with a 0.4mm nozzle.
It can support an accuracy range of 0.1-0.4mm
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
11 Does it support 3mm consumables?
Here is our suggestion for you problem:
The printer only supports 1.75mm diameter consumables
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
12 What consumables does this printer
support?
Here is our suggestion for you problem:
The printer can print PLA, TPU and PETG filaments (ABS requires a constant temperature
environment to print).
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
13 Can the machine be connected to a
computer for printing?
Here is our suggestion for you problem:
The printer supports SD card printing and inline printing.
We recommend printing with an SD card.
Online printing may fail due to network signal problems
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
14 Is the local voltage only 110V
available?
Here is our suggestion for you problem:
Two voltage steps, 115V and 230V, are available for adjustment on the printer power
supply.
Current frequency: 50/60Hz with 24V DC output
Please adjust the printer power supply voltage to a suitable local voltage before using
the printer
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
15 How about the power consumption of
the machine?
Here is our suggestion for you problem:
The printer has an overall power rating of 350W for low power consumption
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
16 What is the maximum temperature that
the nozzle can reach?
Here is our suggestion for you problem:
Nozzles can reach a maximum temperature of 260 degrees
Hot bed can reach a maximum temperature of 100 degrees
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
17 What is the maximum temperature that
can be reached in a hot bed?
18 Does it support power failure
renewal?
Here is our suggestion for you problem:
The machine is a double Z-axis screw structure with power failure renewal function and
filament sensing function.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
19 Does it features a Filament Sensor?
20 Is the machine a double Z-axis screw?
21 Can the machine switch between
English and Chinese?
Here is our suggestion for you problem:
Please click on the "prepare" button on the screen - select the "Language" option to
change Chinese and English
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
22 Are there any requirements for the
computer system?
Here is our suggestion for you problem:
The printer currently supports Windows XP/Vista/7/10/MAC/Linux systems
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
23 What is the printing speed of the
machine?
Here is our suggestion for you problem:
The fastest printing speed of the printer is 150mm/s.
We recommend using 50-100mm/s printing speed is the best
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
Issue about the product operation
24 How to turn on the machine?
Here is our suggestion for you problem:
After turning on the power, press the power switch to turn on the machine.
Before turning on the machine, you need to confirm whether the voltage is adjusted to the
local voltage, so as not to cause damage to the machine
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
25 Do i need to turn off the machine,
after the printing finished?
Here is our suggestion for you problem:
After printing, the machine will automatically cool the printhead and the hot-bed.
If you do not need to continue printing models, you can turn off the power to the machine
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
26 Does the hot bed cool down when
printing is paused?
Here is our suggestion for you problem:
The hot bed does not cool down, but the nozzle does
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
27 How to operate the screen?
Here is our suggestion for you problem:
Turn the knob to select the item
Press the knob to confirm the selection.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
28 How to level the printer?
Here is our suggestion for you problem:
The machine supports automatic leveling, the specific steps can refer to the SD card in
the unboxing video debugging tutorial
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
29 How to heat the nozzle/hot bed?
Here is our suggestion for you problem:
You can select the PLA preheat option or select Control - Temperature - Printhead/Hotbed
Temperature (up to 260 for the printhead and 100 for the hotbed) and just wait for the
temperature to rise.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
30 How to load consumables?
Here is our suggestion for you problem:
1. Turn on the machine - Control - Temperature - Nozzle temperature setting 200 degrees.
2. Cut off the front end of the filament at a 45 degree angle and straighten the front
section of the filament.
3. Press the squeeze clamp or turn the indicator knob to feed the filament into the Teflon
tube along the hole in the squeezer until the filament comes out at the nozzle.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
31 How to replace consumables?
Here is our suggestion for you problem:
1. Please keep the nozzle at 200 degrees.
2. Pinch the extrusion clamp and push the old filament to the front a little.
Then pull it out quickly and put the new filament in
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
32
What about the power suddenly goes
out, before the model is finished
printing?
Here is our suggestion for you problem:
The machine has the function of power off and continue to print.
You can continue to print after re-powering
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
33 Does the machine have requirements
for the use environment?
Here is our suggestion for you problem:
The printer can be used at the usual room temperature.
If the ambient temperature is below 10 degrees, the hot bed temperature needs to be raised
to about 60 degrees
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
34 Is the machine noisy when working?
Here is our suggestion for you problem:
This machine uses 32-bit silent motherboard and fan.
When the machine is working as a whole, the volume generated within 0.5 meters is about 55
decibels
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
35 Can I replace the nozzle with a
different orifice?
Here is our suggestion for you problem:
The default nozzle aperture of this printer is 0.4mm.
You can replace the nozzle with other nozzles of 0.2, 0.6, 0.8, etc.
At the same time, the layer height and wall thickness inside the slicing software also
need to be modified simultaneously
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
36 Does it support printing ABS?
Here is our suggestion for you problem:
ABS has a high demand for ambient temperature.
It needs to be in a constant temperature environment when printing
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
37 Is the machine suitable for children
and the elderly?
Here is our suggestion for you problem:
The nozzle is heated to a high temperature.
Children and the elderly need to use in the case of someone to guide the use to avoid
burns
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
38 How to confirm if the belt is
adjusted properly?
Here is our suggestion for you problem:
Move X/Y axis back and forth or feel the tension of the belt by hand
Tight is stuck, loose is shaking
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
39 Does the machine work continuously
for printing larger models?
Here is our suggestion for you problem:
The machine can print for up to 200 hours continuously.
Please use the printer with confidence
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
40 How do I move the X/Y/Z/E axes
individually?
Here is our suggestion for you problem:
From the printer screen, select the "prepare" option.
Then select the " Move Axis" option to control each axis individually.
You can also select the distance of each movement (0.1mm/1mm/10mm)
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
41 Can I move the nozzle manually?
Here is our suggestion for you problem:
Select the "prepare" option on the screen
Then click on the "disable steppers " option to move the printhead manually
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
Issue about the slicing software use
42 Is there any other slicing software I
can use?
Here is our suggestion for you problem:
Slicing software such as Cura and Simplify can be used
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
43
What is the purpose of the 5 icons in
the upper right corner of the slicing
software?
Here is our suggestion for you problem:
1)）Normal mode
Generally, after opening the STL file normally, this is what is displayed.
Changing parameters must also be changed in this mode.
2）Hover
3）Transparent
4）Perspective mode, usually not used
5）Slice preview mode, able to preview the entire process of printing, more as a slice
reference.
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
44 Is there a requirement for model
format?
Here is our suggestion for you problem:
Currently the model only supports STL, OBJ format, AMF format
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
45 What format is the print file in?
Here is our suggestion for you problem:
Model files recognized by the printer are in Gcode format
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
46 Where to download the slicing
software?
Here is our suggestion for you problem:
You can download the slicing software from our official website
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
47 What are the common settings for
slicing and printing parameters?
Here is our suggestion for you problem:
Please refer to the following common parameter settings
Layer height 0.15mm
Wall thickness 1.2mm
Top bottom layer thickness 1.2mm
Filling 15%~25%
Printing speed 50~60
Nozzle temperature 200~210
Hot bed 45~55
Support type (all support)
Platform attachment type (bottom grid)
Pumping back speed 80
Pumping back length 6~8mm
The rest of the parameters keep the default can
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
48 What is the difference between
partial support and all support?
Here is our suggestion for you problem:
Partial support, adding only the support between the model and the hot bed.
No support between the model and the model is added.
Therefore, we generally recommend to use all supports directly
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
49
The software does not have the
corresponding models, how do I add
them?
Here is our suggestion for you problem:
1. Open the software and find the option to add a model/printer
2. Select "Custom" and enter the size of the machine you need to add.
3. Note that the nozzle aperture column needs to be the same as the actual nozzle aperture
of the machine and check the hot bed option
We hope this helps you.
If you need further assistance with this issue, please feel free to contact us
Andere Handbücher für 3 S1
2
Inhaltsverzeichnis
Andere Ender 3D-Drucker Handbücher
Ender
Ender Ender-3 Pro Bedienungsanleitung
Ender
Ender Ender-3 Montageanleitung
Ender
Ender 3 Series Montageanleitung
Ender
Ender 3 S1 Plus Bedienungsanleitung
Ender
Ender 3 S1 Bedienungsanleitung
Ender
Ender 2 Pro Bedienungsanleitung
Ender
Ender Ender-3 V2 Bedienungsanleitung
Ender
Ender Ender-3 E Bedienungsanleitung
Ender
Ender 3 Series Bedienungsanleitung
Ender
Ender Ender-3 Max Neo Bedienungsanleitung
Ender
Ender Ender-3 Montageanleitung
Ender
Ender 3 Neo Bedienungsanleitung
Ender
Ender Ender-3 S1 Pro Bedienungsanleitung
Ender
Ender 3 S1 Bedienungsanleitung
Ender
Ender 3 Series Bedienungsanleitung
Ender
Ender Ender-7 Bedienungsanleitung
Ender
Ender Ender-3 Pro Montageanleitung
Ender
Ender 3 V2 Neo Bedienungsanleitung
