Endress+Hauser TMD1000 TMD1 Bedienungsanleitung

Products Solutions Services

Operating Instructions

TMD1000 TMD1

Digital Transmitter Module Setting and Adjustment

BA00428G/00/EN/03.18

71427110

2018-12-28

TMD1000 TMD1

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

TMD1000 TMD1 Table of contents

Endress+Hauser 3

Table of contents

1 About this document ................ 4

1.1 Document function ..................... 4

1.2 Symbol .............................. 4

1.3 Documentation ........................ 7

1.4 Registered trademarks ................... 7

2 Basic safety instructions ............ 8

2.1 Requirements for personnel ............... 8

2.2 Designated use ........................ 8

2.3 Workplace safety ....................... 8

2.4 Operational safety ...................... 9

2.5 Product safety ......................... 9

3 Product description ................ 10

3.1 Product design ........................ 10

4 Installation ....................... 15

4.1 Module installation .................... 15

5 Adjustment and setting ............ 16

5.1 Expansion board Exp-A ................. 16

5.2 Temperature system Thermo-A module ..... 22

5.3 4 to 20 mA Output DAC-1 ............... 26

5.4 Parallel output OUT-3 and OUT-4 module ... 30

5.5 Contact output (Alarm) Exp-A module ...... 33

5.6 4 to 20 mA input ADC-2 ................ 35

5.7 Optical communication ODC-1 module ...... 37

5.8 Contact input (Status) Exp-A module ....... 40

5.9 DRM9700 communication DRMM-A

module ............................. 41

5.10 Output for external device operation CNT-2

module ............................. 42

5.11 Level A/D conversion MIF4 module ........ 43

5.12 Alarm contact output CD-688 module ...... 44

Index .................................. 45

About this document TMD1000 TMD1

4 Endress+Hauser

1 About this document

1.1 Document function

These Operating Instructions contain all the information that is required during various

phases of the life cycle of the device: from product identification, incoming acceptance and

storage, to mounting, connection, operation and commissioning through to

troubleshooting, maintenance and disposal.

1.2 Symbol

1.2.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury, as well as a risk of fire or explosion.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in a risk of serious or fatal injury, fire or explosion.

CAUTION

Note

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in a risk of minor or moderate injury and damages to properties.

NOTICE

NOTE!

This symbol contains information on procedures and other facts that do not result in

personal injury.

1.2.2 Electrical symbols

Symbol Meaning

Direct current

Alternating current

Direct current and alternating current

Ground connection

A grounded terminal that, as far as the operator is concerned, is grounded via a

grounding system.

Protective ground connection

A terminal that must be connected to the ground prior to establishing any other

connections.

Equipotential connection

This connects with the grounding system at the plant.It includes equipotential line and

single point ground systems, depending on the norms of each country or company.

1.2.3 Tool symbols

Symbol Meaning

A0013442

Torx screwdriver

A0011220

Flat blade screwdriver

TMD1000 TMD1 About this document

Endress+Hauser 5

Symbol Meaning

A0011219

Phillips screwdriver

A0011221

Allen key

A0011222

Open-ended wrench

1.2.4 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted

Preferred

Procedures, processes or actions that are preferred

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Reference to page

Reference to graphic

Notice or individual step to be observed

… Series of steps

Result of an operation or commissioning

Help in the event of a problem

Visual inspection

Operation via the local display

Operation via operating tool

Write-protected parameter

1.2.5 Symbols in graphics

Symbol Meaning

1, 2, 3 ... Item numbers

… Series of steps

A, B, C, ... Graphics

A-A, B-B, C-C, ... Cross-sections

About this document TMD1000 TMD1

6 Endress+Hauser

Symbol Meaning

Hazardous area

Indicates the hazardous area

Safe area (non-hazardous area)

Indicates the non-hazardous area

1.2.6 Device symbol

Symbol Meaning

Safety instructions

Observe the safety instructions contained in the associated Operating Instructions.

Temperature resistance of the connection cables

Specifies the minimum value of the temperature resistance of the connection cables.

TMD1000 TMD1 About this document

Endress+Hauser 7

1.3 Documentation

For an overview of the scope of the relevant Technical Documentation included with

the product, refer to the following:

• The W@M Device Viewer: Enter the serial number from the nameplate

(www.endress.com/deviceviewer).

• The Endress+Hauser Operations App: Enter the serial number from the nameplate.

1.3.1 Technical Information

The Technical Information contains all the technical data on the device and provides an

overview of the accessories and other products that can be ordered for the device.

Device Technical Information

Digital Transmitter TMD1000 TMD1 TI00463G

1.3.2 Operating Instructions (BA)

The Operating Instructions contain all the information that is required during various

phases of the life cycle of the device: from product identification, incoming acceptance and

storage, to mounting, connection, operation and commissioning through to

troubleshooting, maintenance and disposal.

The Operating Instructions also contain detailed descriptions of each parameter in the

operation menu. The description is aimed at those who work with the device over the

entire life cycle and perform specific configurations.

Device Operating Instructions

Digital Transmitter TMD1000 TMD1 BA00427G

BA00428G

BA00429G

1.3.3 Safety Instructions (XA)

Feature 030 "Approval" Meaning XA

4 TIIS Exd IIB T4 XA01072G

5 FM XP Cl.I Div.1 Gr.C-D, AEx d IIB T4 XA01089G

1.4 Registered trademarks

HART®

Registered trademark of the HART Communication Foundation, Austin, USA

Basic safety instructions TMD1000 TMD1

8 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Be specialists who are trained and have a relevant qualification for this specific

function and task.

‣Be authorized by the plant owner-operator.

‣Be familiar with local/national regulations.

‣Before starting work, read and understand the instructions in the Operating

Instructions and supplementary documentation as well as the certificates (depending

on the application).

‣Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣Be instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣Follow the instructions in this manual.

2.2 Designated use

Application and measured materials

Depending on the version ordered, the device can also be used with potentially explosive,

flammable, poisonous or oxidizing materials.

Devices that are used in hazardous areas have corresponding labels on their nameplates.

To ensure that the device remains in proper condition for the operation time:

‣Only use the device in full compliance with the data on the nameplate and the general

conditions listed in the Operating Instructions and supplementary documentation.

‣Check the nameplate to verify if the device can be put to its intended use in hazardous

areas.

‣If the device is not operated at an atmospheric temperature, compliance with the

relevant basic conditions specified in the relevant device documentation is absolutely

essential.

‣Protect the device permanently against corrosion from environmental influences.

‣Observe the limit values in the "Technical Information".

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to local/national

regulations.

TMD1000 TMD1 Basic safety instructions

Endress+Hauser 9

2.4 Operational safety

Risk of injury!

‣Operate the device in proper technical conditions and fail-safe conditions only.

‣The plant owner-operator is responsible for interference-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

‣If modifications are nevertheless required, contact your Endress+Hauser Sales Center.

Repair

To ensure continued operational safety and reliability:

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe local/national regulations pertaining to repair of an electrical device.

‣Use only original spare parts and accessories from Endress+Hauser.

Ex-area

Observe the following notes to eliminate the risk of danger to persons or the facility when

the device is used in Ex-areas (e.g. explosion protection, pressure equipment safety):

‣Check the model nameplate to ensure that the ordered device is explosion proof.

‣Observe the specifications in the separate supplementary documentation attached to

these Instructions.

2.5 Product safety

This device was designed in accordance with GEP (Good Engineering Practice) to meet

state-of-the-art safety requirements, has been tested and left the factory in a condition in

which it is safe to operate. It meets the general safety standards and legal requirements.

Product description TMD1000 TMD1

10 Endress+Hauser

3 Product description

3.1 Product design

3.1.1 Module types

The following table lists the types of modules and the description of each of them.

Name Functions Size Number of

terminals for

standard use

Remarks

Main CPU - B CPU module A 6 Be sure to install one module.

Exp - A 2-way, 2-wire serial digital

pulse transmission

Contact output (alarm) 4

points

Contact input (status) 4

points

A 2

Transistor output

Thermo - A Average temperature

device

Spot temperature device

A 12

For average and spot temperature

devices

DAC - 1 4 to 20 mA Analog output C 2 2 modules are available to install.

OUT- 3/4 BCD parallel output B 18 OUT-3: Collector common

OUT-4: Emitter common

ADC - 2 4 to 20 mA

Analog signal input

C 2 Available only for use with a 2-wire

transmission board

DRMM- A DRM communication C 2

ODC-1N Optical communication (2-

way, half-duplex

transmission)

Optical digital pulse

C 0

CNT-2 External operation device

output

B 16 Max. 8 points

CD-688 Alarm contact output C 8 4 points for standard (max. 8 points)

Mechanical relay output

• The size indicates how big the modules are: A (large), B (medium), C (small). There

are sizes that cannot be installed depending on the slot position. Refer to the

motherboard section below.

• The number of terminals for standard use indicates the actual number of exterior

terminals for cable connection that are used when installing the modules. As the

connections between the module connector and terminals are wired within the

standard cable pattern, the number of exclusive module terminals may be limited.

• The number of terminals that can be used for entire modules is 30 terminals

maximum (No.7 to No.36) for a small terminal box and 40 terminals maximum

(No.7 to No.48) for a large terminal box.

• Some modules are installed in predetermined slot positions regardless of their sizes.

The positions are shown in the specified slot field.

Andere Handbücher für TMD1000 TMD1

Inhaltsverzeichnis

Andere Endress+Hauser Steuereinheit Handbücher

Endress+Hauser

Endress+Hauser RNF22 Bedienungsanleitung

Endress+Hauser

Endress+Hauser VU340 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivotester FTR325 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit COA451 Bedienungsanleitung

Endress+Hauser

Endress+Hauser BT10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena TOC module Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tankvision NXA820 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CYA251 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR5 series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tank Side Monitor NRF590 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tankvision Multi Scan NXA83B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung