Endress+Hauser Micropilot M FMR 231 Bedienungsanleitung

BA 219F/00/en/12.03

Nr. 52006319

Valid as of software version:

V 01.02.00 (amplifier)

V 01.02.00 (communication)

micropilot M

FMR 231

HART/4...20 mA

Level-Radar

Operating Instructions

HART

FIELD COMMUNICATION PROTOCOL

Micropilot M FMR 231 with HART/4...20 mA

2Endress + Hauser

Brief operating instructions

L00-FMR2xxxx-19-00-00-en-039

!Note!

This operating manual explains the installation and initial start-up for the level

transmitter. All functions that are required for a typical measuring task are taken into

account here. In addition, the Micropilot M provides many other functions that are not

included in this operating manual, such as optimising the measuring point and

converting the measured values.

An overview of all device functions can be found on Page 82.

The operating manual BA 221F/00/en "Description of the instrument functions for

Micropilot M" provides an extensive description of all device functions, which can be

found on the enclosed CD-ROM.

… …

KA 159F/00/a2/05.02

52006292

… …

Micropilot M - Brief operating instructions

- dome

ceiling

- horizontal

cyl.

- bypass

…

- unknown

- DC: <1.9

- DC: 1.9 … 4

- DC: 4 … 10

- DC: >10

- standard

- calm

surface

- add. agitator

…

input E

(see sketch)

input F

(see sketch)

only for

bypass +

stilling well

- ok

- too small

- too big

- unknown

- manual

displayed

(see sketch)

D and L are confirm

or specify

range

suggestion

000

measured value

Group

selection

basic setup

safety settings

system

parameter

display

envelope curve

linearisation

extended calibr.

output (HART, FF)

profibus param.(PA)

092

language

diagnostics

0A0

present

error

002

tank shape

004

process

cond.

005

empty

calibr.

006

full

calibr.

007

pipe

diameter

008

dist./

meas value

051

check

distance

003

medium

cond.

052

range of

mapping

053

start

mapping

008

dist./

meas value

flange:

reference point

of measurement

- envel. curve

- incl. FAC

- incl. cust. map

- single curve

- cyclic

= 100: unlocked

100: locked≠

= 2457: unlocked

2457: locked≠

0E1

plot settings

0E2

recording

curve

0A1

error

0A4

unlock

parameter

threaded connection:

reference point of

measurement

HART

PA , F F

}

Contrast: +or+

Micropilot M FMR 231 with HART/4...20 mA Endress + Hauser

Endress + Hauser 3

Table of contents

1 Safety instructions . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning and operation . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Notes on safety conventions and symbols . . . 5

2 Identification . . . . . . . . . . . . . . . . . . . 6

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . 6

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Certificates and approvals . . . . . . . . . . . . . . . . 9

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . 9

3 Mounting . . . . . . . . . . . . . . . . . . . . . 10

3.1 Quick installation guide . . . . . . . . . . . . . . . . . 10

3.2 Incoming acceptance, transport, storage . . . 11

3.3 Installation conditions . . . . . . . . . . . . . . . . . . 12

3.4 Installation instructions . . . . . . . . . . . . . . . . . 18

3.5 Post-installation check . . . . . . . . . . . . . . . . . . 20

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . 21

4.2 Connecting the measuring unit . . . . . . . . . . . 23

4.3 Recommended connection . . . . . . . . . . . . . . 26

4.4 Degree of protection . . . . . . . . . . . . . . . . . . . 26

4.5 Post-connection check . . . . . . . . . . . . . . . . . 26

5 Operation . . . . . . . . . . . . . . . . . . . . . 27

5.1 Quick operation guide . . . . . . . . . . . . . . . . . . 27

5.2 Display and operating elements . . . . . . . . . . 29

5.3 Local operation . . . . . . . . . . . . . . . . . . . . . . . 31

5.4 Display and acknowledging error messages 34

5.5 HART communication . . . . . . . . . . . . . . . . . . 35

6 Commissioning . . . . . . . . . . . . . . . . 38

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . 38

6.2 Switching on the measuring device . . . . . . . . 38

6.3 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.4 Basic Setup with the VU 331 . . . . . . . . . . . . . 41

6.5 Basic Setup with the ToF Tool . . . . . . . . . . . . 53

7 Maintenance . . . . . . . . . . . . . . . . . . 58

8 Accessories . . . . . . . . . . . . . . . . . . . 59

9 Trouble-shooting. . . . . . . . . . . . . . . 61

9.1 Trouble-shooting instructions . . . . . . . . . . . . 61

9.2 System error messages . . . . . . . . . . . . . . . . . 62

9.3 Application errors . . . . . . . . . . . . . . . . . . . . . 64

9.4 Orientation of the Micropilot . . . . . . . . . . . . . . 66

9.5 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.6 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

9.7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

9.8 Software history . . . . . . . . . . . . . . . . . . . . . . . 75

9.9 Contact addresses of Endress+Hauser . . . . . 75

10 Technical data . . . . . . . . . . . . . . . . . 76

10.1 Additional technical data . . . . . . . . . . . . . . . . 76

11 Appendix . . . . . . . . . . . . . . . . . . . . . . 82

11.1 Operating menu HART (display modul),

ToF Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

11.2 Operating matrix HART / Commuwin II . . . . . . 84

11.3 Description of functions . . . . . . . . . . . . . . . . . 85

11.4 Function and system design . . . . . . . . . . . . . . 86

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Safety instructions Micropilot M FMR 231 with HART/4...20 mA

4Endress + Hauser

1Safetyinstructions

1.1 Designated use

The Micropilot M FMR 231 is a compact radar level transmitter for the continuous,

contactless measurement of liquids, pastes and sludge. The device can also be freely

mounted outside closed metal vessels because of its operating frequency of about

6 GHz and a maximum radiated pulsed energy of 1mW (average power output 1 µW).

Operation is completely harmless to humans and animals.

1.2 Installation, commissioning and operation

The Micropilot M has been designed to operate safely in accordance with current

technical, safety and EU standards. If installed incorrectly or used for applications for

which it is not intended, however, it is possible that application-related dangers may

arise, e.g. product overflow due to incorrect installation or calibration. For this reason,

the instrument must be installed, connected, operated and maintained according to the

instructions in this manual: personnel must be authorised and suitably qualified. The

manual must have been read and understood, and the instructions followed.

Modifications and repairs to the device are permissible only when they are expressly

approved in the manual.

1.3 Operational safety

1.3.1 Hazardous areas

Measuring systems for use in hazardous environments are accompanied by separate

"Ex documentation", which is an integral part of this Operating Manual. Strict

compliance with the installation instructions and ratings as stated in this supplementary

documentation is mandatory.

•Ensure that all personnel are suitably qualified.

•Observe the specifications in the certificate as well as national and local regulations.

1.3.2 FCC approval

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

"Caution!

Changes or modifications not expressly approved by the part responsible for

compliance could void the user’s authority to operate the equipment.

Micropilot M FMR 231 with HART/4...20 mA Safety instructions

Endress + Hauser 5

1.4 Notes on safety conventions and symbols

In order to highlight safety-relevant or alternative operating procedures in the manual,

the following conventions have been used, each indicated by a corresponding symbol

in the margin.

Symbol Meaning

#Warning!

A warning highlights actions or procedures which, if not performed correctly,

will lead to personal injury, a safety hazard or destruction of the instrument

"Caution!

Caution highlights actions or procedures which, if not performed correctly,

may lead to personal injury or incorrect functioning of the instrument

!Note!

A note highlights actions or procedures which, if not performed correctly, may

indirectly affect operation or may lead to an instrument response which is not

planned

0Device certified for use in explosion hazardous area

If the device has this symbol embossed on its name plate it can be installed in

an explosion hazardous area

-Explosion hazardous area

Symbol used in drawings to indicate explosion hazardous areas.

– Devices located in and wiring entering areas with the designation

“explosion hazardous areas” must conform with the stated type of protection

Safe area (non-explosion hazardous area)

Symbol used in drawings to indicate, if necessary, non-explosion hazardous

areas.

– Devices located in safe areas still require a certificate if their outputs run into

explosion hazardous areas

%Direct voltage

A terminal to which or from which a direct current or voltage may be applied or

supplied

&Alternating voltage

A terminal to which or from which an alternating (sine-wave) current or voltage

may be applied or supplied

)Grounded terminal

A grounded terminal, which as far as the operator is concerned, is already

grounded by means of an earth grounding system

*Protective grounding (earth) terminal

A terminal which must be connected to earth ground prior to making any other

connection to the equipment

+Equipotential connection (earth bonding)

A connection made to the plant grounding system which may be of type e.g.

neutral star or equipotential line according to national or company practice

Identification Micropilot M FMR 231 with HART/4...20 mA

6Endress + Hauser

2 Identification

2.1 Device designation

2.1.1 Nameplate

The following technical data are given on the instrument nameplate:

L00-FMR2xxxx-18-00-00-en-001

Fig. 1: Information on the nameplate of the Micropilot M (example)

2.1.2 Ordering structure

Ordering structure Micropilot M FMR 231

10 Certificates

A For non-hazardous areas

F For non-hazardous areas + WHG

1 ATEX II 1/2 G EEx ia IIC T6

2 ATEX II 1/2 G EEx ia IIC T6, note safety instruction (XA) for electrostatic charging!

6 ATEX II 1/2 G EEx ia IIC T6 + WHG

7 ATEX II 1/2 G EEx ia IIC T6 + WHG, note safety instruction (XA) for electrostatic charging!

3 ATEX II 1/2 G EEx em [ia] IIC T6

8 ATEX II 1/2 G EEx em [ia] IIC T6 + WHG

4 ATEX II 1/2 G EEx d [ia] IIC T6

5 ATEX II 1/2 G EEx d [ia] IIC T6, note safety instruction (XA) for electrostatic charging!

G ATEX II 3 G EEx nA II T6

S FM IS - Class I, Division 1, Group A-D

T FM XP - Class I, Division 1, Group A-D

N CSA General Purpose

U CSA IS - Class I, Division 1, Group A-D

V CSA XP - Class I, Division 1, Group A-D

K TIIS EEx ia IIC T4

L TIIS EEx d [ia] IIC T4

W AUS Ex ib IIC T6

Y Special version

FMR 231- Product designation (part 2)

Micropilot M FMR 231 with HART/4...20 mA Identification

Endress + Hauser 7

Ordering structure Micropilot M FMR 231 (continued)

20 Type of antenna, O-ring, inactive length

Type Length Material O-ring Nozzle length

A Rod antenna 360 mm / 14" PPS, antistatic Viton 100 mm / 4"

B Stabantenne 510 mm / 20" PPS, antistatic Viton 250 mm / 10"

E Stabantenne 390 mm / 15" PTFE, fully insulated 100 mm / 4"

F Stabantenne 540 mm / 21" PTFE, fully insulated 250 mm / 10"

H Stabantenne 390 mm / 15" PPS, antistatic + fully insulated 100 mm / 4"

J Stabantenne 540 mm / 21" PPS, antistatic + fully insulated 250 mm / 10"

Y Special version

30 Process connection, material

Threaded connection Standard Material

GGJ 1½" BSPT (R 1½") DIN 2999 316L

GGS 1½" BSPT (R 1½") DIN 2999 PVDF

GNJ NPT 1½" 316L

GNS NPT 1½" PVDF

Sanitary coupling Standard Material

MFJ DN50 dairy coupling DIN 11851 316L

HFJ DN50 aseptic DIN 11864-1 Form A 316L

for tubes according to DIN 11850

TEJ 2" Tri-clamp ISO 2852 316L

TLJ 3" Tri-clamp ISO 2852 316L

Flange Dia/Pressure Standard Material

BFJ DN50 PN16 EN 1092-1, A1) 316L

CFJ DN50 PN16 EN 1092-1, B11) 316L

CFK DN50 PN16 EN 1092-11) PTFE >316L

BMJ DN80 PN16 EN 1092-1, A1) 316L

CMJ DN80 PN16 EN 1092-1, B11) 316L

BNJ DN80 PN40 EN 1092-1, A1) 316L

CNJ DN80 PN40 EN 1092-1, B11) 316L

CMK DN80 PN16 EN 1092-11) PTFE >316L

BQJ DN100 PN16 EN 1092-1, A1) 316L

CQJ DN100 PN16 EN 1092-1, B11) 316L

CQK DN100 PN16 EN 1092-11) PTFE >316L

BWJ DN150 PN16 EN 1092-1, A1) 316L

CWJ DN150 PN16 EN 1092-1, B11) 316L

CWK DN150 PN16 EN 1092-11) PTFE (black) >316L

disc made of antistatic PTFE (black)

AEJ 2"/150 lbs ANSI B16.5 316L

AEK 2"/150 lbs ANSI B16.5 PTFE >316L

ALJ 3"/150 lbs ANSI B16.5 316L

AMJ 3"/300 lbs ANSI B16.5 316L

ALK 3"/150 lbs ANSI B16.5 PTFE >316L

APJ 4"/150 lbs ANSI B16.5 316L

AQJ 4"/300 lbs ANSI B16.5 316L

APK 4"/150 lbs ANSI B16.5 PTFE >316L

AVJ 6"/150 lbs ANSI B16.5 316L

AVK 6"/150 lbs ANSI B16.5 PTFE (black) >316L

disc made of antistatic PTFE (black)

KEJ 10 K 50A JIS B2210 316L

KEK 10 K 50A JIS B2210 PTFE >316L

KLJ 10 K 80A JIS B2210 316L

KLK 10 K 80A JIS B2210 PTFE >316L

KPJ 10 K 100A JIS B2210 316L

KPK 10 K 100A JIS B2210 PTFE >316L

KVJ 10 K 150A JIS B2210 316L

KVK 10 K 150A JIS B2210 PTFE (black) >316L

disc made of antistatic PTFE (black)

YY9 Special version

1) agreeable to DIN 2527

FMR 231- Product designation (part 1)

Identification Micropilot M FMR 231 with HART/4...20 mA

8Endress + Hauser

Ordering structure Micropilot M FMR 231 (continued)

40 Output and menu based operation

A 4…20 mA HART with VU 331 (4-line alphanumeric display)

B4…20mAHART

K 4…20 mA HART, prepared for FHX40, mounting of remote display (accessoty)

C PROFIBUS PA with VU 331 (4-line alphanumeric display)

D PROFIBUS PA

L PROFIBUS PA, prepared for FHX40, mounting of remote display (accessoty)

E Foundation Fieldbus with VU 331 (4-line alphanumeric display)

F Foundation Fieldbus

M Foundation Fieldbus, prepared for FHX40, mounting of remote display (accessoty)

Y Special version

50 Housing

A Aluminium F12-housing, coated, IP65

B 316L F23-housing, IP65/NEMA 4x

C Aluminium T12-housing with separate connection compartment, coated, IP65

D Aluminium T12-housing with separate connection compartment, coated, IP65,

overvoltage protection

Y Special version

60 Gland / Entry

2 M20x1.5 cable gland (for EEx d: cable entry)

3 G ½ cable entry

4 ½ NPT cable entry

5 PROFIBUS PA M12 plug

6 7/8" FF plug

9 Special version

70 Gastight feed through

A without gastight feed through

C with gastight feed through

80 Additional options

A Additional options not selected

B 3.1.B material, wetted parts 316L, Inspection Certificate EN 10204,

acc. specification 52005759

S GL (German Lloyd) marine certificate

Y Special version

FMR 231- Complete product designation

Micropilot M FMR 231 with HART/4...20 mA Identification

Endress + Hauser 9

2.2 Scope of delivery

"Caution!

It is essential to follow the instructions concerning the unpacking, transport and storage

of measuring instruments given in the chapter "Incoming acceptance, transport,

storage" on Page 11!

The scope of delivery consists of:

•Assembled instrument

•2 ToF Tool - FieldTool®Package CD-ROMs

– CD 1: ToF Tool - FieldTool®Program

Program including Device Descriptions (device drivers) and documentation for all

Endress+Hauser devices wich are operable using ToF Tool

– CD 2: ToF Tool - FieldTool®Utilities

Utility program (e.g. Adobe Acrobat Reader, MS Internet Explorer)

•Accessories (→Chap. 8)

Accompanying documentation:

•Short manual (basic setup/troubleshooting): housed in the instrument

•Operating manual (this manual)

•Approval documentation: if this is not included in the operating manual.

!Note!

The operating manual "Description of Instrument Functions" you can be found on the

enclosed CR-ROM.

2.3 Certificates and approvals

CE mark, declaration of conformity

The instrument is designed to meet state-of-the-art safety requirements, has been

tested and left the factory in a condition in which it is safe to operate. The instrument

complies with the applicable standards and regulations in accordance with EN 61010

"Protection Measures for Electrical Equipment for Measurement, Control, Regulation

and Laboratory Procedures". The instrument described in this manual thus complies

with the statutory requirements of the EG directives. Endress+Hauser confirms the

successful testing of the instrument by affixing to it the CE mark.

2.4 Registered trademarks

KALREZ®, VITON®, TEFLON®

Registered trademark of the company, E.I. Du Pont de Nemours & Co., Wilmington, USA

TRI-CLAMP®

Registered trademark of the company, Ladish & Co., Inc., Kenosha, USA

HART®

Registered trademark of HART Communication Foundation, Austin, USA

ToF®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg,

Germany

PulseMaster®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg,

Germany

PhaseMaster®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg,

Germany

Mounting Micropilot M FMR 231 with HART/4...20 mA

10 Endress + Hauser

3 Mounting

3.1 Quick installation guide

L00-FMR231xx-17-00-00-en-003

90°

DN50

ANSI 2”

DN80…150

ANSI 3…6”

F12/F23 housing

T12 housing

Turn housing

Observe orientation when installing!

Installation in tank (free space):

Mark on process connector facing the nearest tank wall!

The housing can be turned 350°

in order to simplify access to the

display and the terminal compartment

Allen key

4 mm

1½” BSPT (R 1½”)

1½NPT

mark at instrument flange

or threaded boss

Andere Handbücher für micropilot M FMR 231

Inhaltsverzeichnis

Andere Endress+Hauser Radar Handbücher

Endress+Hauser

Endress+Hauser Hart Micropilot FMR60B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP55 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR60 Handbuch

Endress+Hauser

Endress+Hauser Micropilot S FMR530 Technische Daten

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR53 Technische Daten

Endress+Hauser

Endress+Hauser Levelflex FMP55 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR63B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR20 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR62B Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR67B PROFINET with Ethernet-APL Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR63B PROFIBUS PA Handbuch

Endress+Hauser

Endress+Hauser Micropilot FMR50 Bedienungs- und Montageanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR56 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR50 Technische Daten

Endress+Hauser

Endress+Hauser PROFIBUS PA Micropilot FMR53 Technische Daten

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Levelflex FMP51 Technische Daten

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR50 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Bedienungsanleitung

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR51 Technische Daten

Endress+Hauser

Endress+Hauser Levelflex FMP53 PROFIBUS PA Technische Daten

Endress+Hauser

Endress+Hauser Micropilot M FMR244 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser HART Micropilot S FMR533 Technische Daten

Beliebte Radar Handbücher anderer Marken

SAW D2L

SAW D2L Valentine One Gen2 Bedienungsanleitung

Raymarine

Raymarine Raytheon R20X Bedienungsanleitung

Simrad

Simrad CA34 Bedienungsanleitung

ECHOMAX

ECHOMAX Active-X-Band Bedienungsanleitung

AGD

AGD 340 Bedienungsanleitung

Kustom Signals

Kustom Signals Eagle 3 Bedienungsanleitung

SYMEO

SYMEO STU Bedienungsanleitung

Axis

Axis D2110-VE Bedienungsanleitung

MALA

MALA MIRA Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 5300 Bedienungsanleitung

Rosemount

Rosemount 5300 Series Bedienungsanleitung

TERMA

TERMA SCANTER 5102 Bedienungsanleitung

GSSI

GSSI UtilityScan Bedienungsanleitung

Acconeer

Acconeer A111 Bedienungsanleitung

Crosley

Crosley CR37 Bedienungsanleitung

AGD

AGD 318 Bedienungsanleitung

Cobra

Cobra SLR 650G Bedienungsanleitung

Faselase

Faselase D10 Bedienungsanleitung

Endress+Hauser micropilot M FMR 231 Bedienungsanleitung

Beliebte Radar Handbücher anderer Marken