Endress+Hauser Flowphant T DTT31 Flowphant T DTT35 Bedienungsanleitung

Products Solutions Services

Operating Instructions

Flowphant T DTT31, DTT35

Flow switch

80 50

BA00235R/09/EN/17.18

71415550

2018-02-15

Valid as of version

01.00 (device version)

Flowphant T DTT31, DTT35 Table of contents

Endress+Hauser 3

Table of contents

1 About this document ........... 4

1.1 Document function ................... 4

1.2 Symbols used ........................ 4

2 Basic safety instructions ....... 5

2.1 Requirements for the personnel ........ 5

2.2 Designated use ...................... 6

2.3 Workplace safety .................... 6

2.4 Operational safety ................... 6

2.5 Product safety ....................... 6

2.6 IT security .......................... 7

3 Incoming acceptance and

product identification .......... 7

3.1 Incoming acceptance ................. 7

3.2 Product identification ................. 7

3.3 Storage and transport ................. 8

4 Installation ...................... 8

4.1 Installation conditions ................ 8

5 Electrical connection .......... 12

5.1 Connection conditions ............... 12

6 Operation options ............. 14

6.1 Overview of operation options ........ 14

6.2 Structure and function of the operating

menu ............................. 16

6.3 Access to the operating menu via the

operating tool ...................... 26

7 Diagnostics and

troubleshooting ............... 27

7.1 General troubleshooting ............. 27

7.2 Firmware history ................... 29

8 Maintenance .................. 30

9 Repair .......................... 30

9.1 Return ............................ 30

9.2 Disposal ........................... 30

10 Accessories .................... 31

10.1 Device-specific accessories ............ 31

10.2 Communication-specific accessories ... 34

11 Technical data ................. 35

11.1 Output ............................ 35

11.2 Power supply ....................... 36

11.3 Environment ....................... 36

11.4 Process ............................ 37

11.5 Mechanical construction ............. 38

11.6 Certificates and approvals ............ 41

11.7 Supplementary documentation ........ 42

About this document Flowphant T DTT31, DTT35

4 Endress+Hauser

1 About this document

1.1 Document function

These Operating Instructions contain all the information that is required in various phases of

the life cycle of the device: from product identification, incoming acceptance and storage, to

mounting, connection, operation and commissioning through to troubleshooting,

maintenance and disposal.

1.2 Symbols used

1.2.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

NOTE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.2.2 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Preferred

Procedures, processes or actions that are preferred.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation.

Reference to page.

Reference to graphic.

Flowphant T DTT31, DTT35 Basic safety instructions

Endress+Hauser 5

Symbol Meaning

Notice or individual step to be observed.

… Series of steps.

Result of a step.

Help in the event of a problem.

Visual inspection.

1.2.3 Symbols in graphics

Symbol Meaning

1, 2, 3, ... Item numbers

, … Series of steps

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

Hazardous area

Safe area (non-hazardous area)

Flow direction

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the application).

‣Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣Are instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣Follow the instructions in this manual.

Basic safety instructions Flowphant T DTT31, DTT35

6 Endress+Hauser

2.2 Designated use

The device is a flow switch for monitoring mass flow rates in industrial processes. The device

is designed to meet state-of-the-art safety requirements and complies with applicable

standards and EC regulations. The device can, however, be a source of danger if used

incorrectly or for anything other than the designated use.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

For welding work on the piping:

‣Do not ground the welding unit via the measuring device.

If working on and with the device with wet hands:

‣Due to the increased risk of electric shock, gloves must be worn.

2.4 Operational safety

• Functional safety:

The device has been developed according to the IEC 61508 and IEC 61511-1 (FDIS)

standards. The device version with a PNP switch output and additional analog output is

fitted with mechanisms for error detection and prevention within the electronics and

software.

• Hazardous area:

The device is not approved for use in hazardous areas.

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for the interference-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

‣If modifications are nevertheless required, consult with the manufacturer.

Repair

To ensure continued operational safety and reliability:

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to the repair of an electrical device.

‣Use only original spare parts and accessories from the manufacturer.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which it

is safe to operate.

Flowphant T DTT31, DTT35 Incoming acceptance and product identification

Endress+Hauser 7

It meets general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. .

2.6 IT security

Our warranty is valid only if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the settings.

IT security measures, which provide additional protection for the device and associated data

transfer, must be implemented by the operators themselves in line with their security

standards.

3 Incoming acceptance and product identification

3.1 Incoming acceptance

Proceed as follows on receipt of the device:

1. Check whether the packaging is intact.

2. If damage is discovered:

Report all damage immediately to the manufacturer.

3. Do not install damaged material, as the manufacturer cannot otherwise guarantee

compliance with the safety requirements and cannot be held responsible for the

consequences that may result.

4. Compare the scope of delivery against the contents of your order.

5. Remove all the packaging material used for transportation.

3.2 Product identification

The device can be identified in the following ways:

• Nameplate specifications

• Enter the serial number from the nameplate in the W@M Device Viewer

(www.endress.com/deviceviewer): all data relating to the device and an overview of the

Technical Documentation supplied with the device are displayed.

The nameplate illustrated below is designed to help users identify specific product

information, such as the serial number, design, variables, configuration and device approvals:

Installation Flowphant T DTT31, DTT35

8 Endress+Hauser

Flowphant T

Made in Germany D-87484 Nesselwang

Order Code: DTT3x-xxxxxxxx

Ser.No.: xxxxxxxxxxxxxx

TAG No.: Xxxxxxxxxxxxxxxxxx

Xxxxxxxxxxxxxxxxxx

Rel.: X.XX.XX

Flow (0.03… 3m/s; -20 °C...+85 °C)

-40°C <Ta < 85°C

Output < 250 mA

Current consump.100mA

18 - 30V DC

PNP

L+

L-

1 2

IP6X

A0006981

 1 Nameplate for device identification

1 Order code

2 Serial number

3 TAG number

4 Release number

5 Connection data

6 Measuring range

7 Ambient temperature range

8 Degree of protection

9 Approvals

10 Connection diagram

Check the data on the nameplate of the device and compare them against the

requirements of the measuring point.

3.3 Storage and transport

Pack the device so that it is reliably protected against impact when it is stored (and

transported). The original packaging offers the best protection.

Storage temperature –40 to +85 °C (–40 to +185 °F)

4 Installation

4.1 Installation conditions

4.1.1 Dimensions

→  38

Flowphant T DTT31, DTT35 Installation

Endress+Hauser 9

4.1.2 General installation instructions

NOTICE

Damage to the device.

‣To ensure correct monitoring, the sensor must be installed in a way that produces a fully

developed flow profile.

‣Stabilization sections (5x DN) must be provided in the pipe downstream from a pump, pipe

elbows, internal fixtures and cross-sectional changes.

NOTICE

Damage to the device.

‣Do not turn the device into the process connection thread at the housing→  9.

‣Always install the device at the wrench flats.

‣Use a suitable open-ended wrench →  9.

‣The local display can be rotated electronically by 180 °→  14.

‣The top housing section can be rotated mechanically by up to 310 °.

Installation Flowphant T DTT31, DTT35

10 Endress+Hauser

• The sensor tip must be completely surrounded by the

medium

• Position the sensor tip in the area of maximum flow

velocity (pipe center)

• Minimum sensor immersion length

Li ≥ 10 mm (0.4 in).

A0006976

 2 Installation instructions (example)

Orientation

• For horizontal pipes: lateral installation. Installation

from above only if the pipe is completely filled with

medium

• For vertical pipes: installation in the ascending pipe

• For DTT35: install at an angle of at least 3 ° for self-

draining

=3°

A0006977

 3 Correct orientation

NOTICE

If the device is installed incorrectly this can result in

incorrect measurements!

‣Do not install in down pipes open towards the end.

‣The sensor tip should never touch the pipe wall.

A0006978

 4 Incorrect installation!

Inhaltsverzeichnis

Andere Endress+Hauser Schalten Handbücher

Endress+Hauser

Endress+Hauser Cerabar PMP11 Bedienungsanleitung

Endress+Hauser

Endress+Hauser nivotester FTL 325 P Handbuch

Endress+Hauser

Endress+Hauser Nivotester FTC 422 Bedienungsanleitung

Endress+Hauser

Endress+Hauser prosonic T FTU 230 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant S FTL70 7 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivotester FTL 375 N 3 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant T FTL20H Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant T FTM260 Handbuch

Endress+Hauser

Endress+Hauser Soliswitch FTE20 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Ceraphant T PTC31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL64 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RTA421 Handbuch

Endress+Hauser

Endress+Hauser Liquiphant FTL31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 55 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL62 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquipoint FTW 31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RTA421 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL62 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solicap M FTI55 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant M FTL50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser nivotester FTW 420 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant M FTM50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquipoint FTW33 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung