Endress+Hauser Liquiphant FTL62 Technische Daten

Products Solutions Services

Brief Operating Instructions

Liquiphant FTL62

Vibronic

Point level switch with highly corrosion-resistant

coating for liquids

These Instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

Detailed information about the device can be found in the

Operating Instructions and the other documentation:

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

KA01479F/00/EN/02.22-00

71566287

2022-04-05

Associated documentation Liquiphant FTL62

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Symbols

2.1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

Liquiphant FTL62 About this document

Endress+Hauser 3

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.1.2 Electrical symbols

Ground connection

Grounded clamp, which is grounded via a grounding system.

Protective earth (PE)

Ground terminals, which must be grounded prior to establishing any other connections. The

ground terminals are located on the inside and outside of the device.

2.1.3 Tool symbols

Flat-blade screwdriver

Allen key

Open-ended wrench

2.1.4 Symbols for certain types of information

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information

Reference to documentation

Reference to another section

Series of steps

2.1.5 Symbols in graphics

A, B, C ... View

1, 2, 3 ... Item numbers

Hazardous area

Safe area (non-hazardous area)

Basic safety instructions Liquiphant FTL62

4 Endress+Hauser

3 Basic safety instructions

3.1 Requirements for the personnel

The personnel must fulfill the following requirements to carry out the necessary tasks, e. g.,

commissioning and maintenance:

‣Trained, qualified specialists must have a relevant qualification for the specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Must have read and understood the instructions in the manual and supplementary

documentation

‣Follow instructions and comply with conditions

3.2 Intended use

• Only use the device for liquids

• Improper use can pose hazards

• Ensure that the measuring device is free of defects while it is in operation

• Use the device only for media to which the wetted materials have an adequate level of

resistance

• Do not exceed or drop below the relevant limit values for the device

For more details, see the Technical Documentation

3.2.1 Incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Residual risks

Due to heat transfer from the process, the temperature of the electronics housing and the

assemblies contained therein may rise to 80 °C (176 °F) during operation.

Danger of burns from contact with surfaces!

‣If necessary, ensure protection against contact to prevent burns.

For requirements concerning functional safety in accordance with IEC 61508, the associated

SIL documentation must be observed.

3.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

3.4 Operational safety

Risk of injury!

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for ensuring the interference-free operation of the device.

Liquiphant FTL62 Incoming acceptance and product identification

Endress+Hauser 5

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability:

‣Only perform repair work on the device if this is expressly permitted.

‣Observe federal/national regulations pertaining to the repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

Hazardous area

To eliminate danger to persons or the facility when the device is used in the hazardous area

(e.g. explosion protection):

‣Check the nameplate to verify whether the ordered device can be used for the intended

purpose in the hazardous area.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of this manual.

3.5 Product safety

This device is designed in accordance with good engineering practice to meet state-of-the-art

safety requirements, has been tested, and left the factory in a condition in which it is safe to

operate.

It meets the general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

4 Incoming acceptance and product identification

4.1 Incoming acceptance

Check the following during incoming acceptance:

 Are the order codes on the delivery note and the product sticker identical?

 Are the goods undamaged?

 Do the data on the nameplate match the ordering information on the delivery note?

 If required (see nameplate): are the Safety Instructions e.g. XA provided?

If one of these conditions is not met, please contact the manufacturer's sales office.

Mounting Liquiphant FTL62

6 Endress+Hauser

4.2 Product identification

The following options are available for the identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter serial number from nameplates in W@M Device Viewer

www.endress.com/deviceviewer. All of the information on the measuring device is

displayed along with an overview of the scope of technical documentation provided.

• Enter the serial number on the nameplate into the Endress+Hauser Operations app or scan

the 2-D matrix code on the nameplate with the Endress+Hauser Operations app

4.2.1 Electronic insert

Identify the electronic insert via the order code on the nameplate.

4.2.2 Nameplate

The information that is required by law and is relevant to the device is shown on the

nameplate.

4.3 Storage and transport

4.3.1 Storage conditions

Use original packaging.

Storage temperature

–40 to +80 °C (–40 to +176 °F)

Optional: –50 °C (–58 °F), –60 °C (–76 °F)

4.3.2 Transporting the device

NOTICE

Flange, pipe extension and tuning fork are either plastic-coated or enamel-coated.

Scratches or impacts may cause damage to the coated surface of the device.

‣Hold the device only by the housing, flange or extension pipe, protect coated surface

appropriately.

‣Transport the device to the measuring point in the original packaging.

Do not bend, shorten or extend the tuning fork.

5 Mounting

LWARNING

Loss of protection rating if the device is opened in a wet environment.

‣Only open the device in a dry environment!

Liquiphant FTL62 Mounting

Endress+Hauser 7

Mounting instructions

• Any orientation for device with short pipe up to approx. 500 mm (19.7 in)

• Vertical orientation from above for device with long pipe

• Minimum distance between the fork tip and the tank wall or pipe wall: 10 mm (0.39 in)

A0042153

 1 Installation examples for a vessel, tank or pipe

1 Vessel insulation (example with temperature spacer/pressure-tight feedthrough)

If process temperatures are high, the device should be included in a vessel insulation system to prevent

the electronics from heating as a result of thermal radiation or convection.

5.1 Mounting requirements

NOTICE

Scratches or impacts damage the coated surface of the device.

‣Ensure the device is handled properly and professionally during all mounting work.

In the case of sensors with an ECTFE or PFA coating, a PTFE seal is fixed on the flange.

5.1.1 Take switch point into consideration

The following are typical switch points, depending on the orientation of the point level switch

and coating.

Water +23 °C (+73 °F)

Minimum distance between the fork tip and the tank wall or pipe wall: 10 mm (0.39 in)

Mounting Liquiphant FTL62

8 Endress+Hauser

Plastic-coated tuning fork

~13 (0.5)

~12.5 (0.49)

~6 (0.24)

A0042269

 2 Typical switch points, plastic-coated tuning fork. Unit of measurement mm (in)

A Installation from above

B Installation from below

C Installation from the side

D Switch point

Enamel-coated tuning fork

~17 (0.67)

~14 (0.55)

~5 (0.2)

A0043327

 3 Typical switch points, enamel-coated tuning fork. Unit of measurement mm (in)

A Installation from above

B Installation from below

C Installation from the side

D Switch point

5.1.2 Take viscosity into consideration

Viscosity values

• Low viscosity : < 2 000 mPa⋅s

• High viscosity: > 2 000 to 10 000 mPa⋅s

Liquiphant FTL62 Mounting

Endress+Hauser 9

Low viscosity

It is permitted to position the tuning fork within the installation socket.

> 25 (0.98)

> !50 (1.97)

A0033297

 4 Installation example for low-viscosity liquids. Unit of measurement mm (in)

High viscosity

NOTICE

Highly viscous liquids may cause switching delays.

‣Make sure that the liquid can run off the tuning fork easily.

‣Deburr the socket surface.

The tuning fork must be located outside the installation socket!

> 40 (1.57)

A0037348

 5 Installation example for a highly viscous liquid. Unit of measurement mm (in)

Mounting Liquiphant FTL62

10 Endress+Hauser

5.1.3 Avoid buildup

A0042206

 6 Installation examples for a highly viscous process medium

5.1.4 Take clearance into consideration

A0033236

 7 Take clearance outside the tank into consideration

Andere Handbücher für Liquiphant FTL62

Inhaltsverzeichnis

Andere Endress+Hauser Schalten Handbücher

Endress+Hauser

Endress+Hauser Nivotester FTL 375 N 3 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivotester FTC 422 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL51B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquipoint FTW 31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL51B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant M FTM52 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquipoint T FTW31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant M FTL50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant M FTM50 Handbuch

Endress+Hauser

Endress+Hauser nivotester FTC 420 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquipoint FTW 31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant T FTM260 Handbuch

Endress+Hauser

Endress+Hauser soliphant II FTM 30 DR Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant T FTM20 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliswitch FTE20 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL33 IO-Link Technische Daten

Endress+Hauser

Endress+Hauser nivector FTC 968 Bedienungsanleitung

Endress+Hauser

Endress+Hauser nivocompact FTC 831 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivotester FTC325 PFM Bedienungsanleitung

Endress+Hauser

Endress+Hauser prosonic T FTU 230 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Ceraphant T PTC31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant FTL62 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch