ENERGY KINETICS SYSTEM 2000 Accel CS Montageanleitung

nnual Tune Up

and Inspection

Accel CS Boiler

Page 1 of 3

Step 1 Open Front Cover

Turn off power to system and close main manual gas valve when servicing.

1. Loosen the (4) screws holding the upper front boiler jacket access panel and set the

panel aside.

2. Remove the (2) screws holding the jacket top cover on, tilt up and slide forward to

remove.

Step 2 Disconnect Gas Line and Burner Fan Electrical Connections

1. Shut off gas supply. Remove the direct air intake and the associated gas valve

reference hose.

2. Using two wrenches disconnect the flexible gas line below at the flare fitting.

3. Disconnect electrical wiring from burner head. Models may have a single large

connector or individual connectors for fan, ignitor, and flame rod. Disconnect the

two electrical wiring connectors at the fan housing. The connector holding clips are

on the sides of the three pin connector and on the back of the four pin connector.

They are both press-to-release type. Disconnect the electrical wiring connector

connecting the wires to the top of the burner.

4. Remove the (6) burner flange nuts holding the burner flange to the top of the heat

exchanger.

5. Lift the burner and flange straight up about 2 inches and rotate the fan toward you.

Tilt the fan down while picking up on the burner. Lift it high enough to remove it

from the boiler. Gently loosen the refractory if it adheres to the pressure vessel.

6. Place the burner on a flat surface with the nozzle pointing upward. Do not touch the

mesh burner head and be careful not to damage the igniter or sense rod.

Please refer to owner and installation manual for complete details.

Step 3 Clean Turbulators, Flame Rod and Burner Sight Glass

1. Remove (6) turbulators. If they all look clean, you’re done. Otherwise twist and

clean all turbulators. Never operate the boiler without all turbulators installed.

2. If it looks like the boiler needs to be flushed, remove the condensate trap and place

a bucket or tray below the condensate outlet and spray the furnace area with a

citric acid based cleaner and a soft brush. Then rinse thoroughly with clean water

and push back down into the tube.

3. If the condensate trap was removed, then reinstall the trap.

4. When using the citrus cleaner, wear eye protection and rubber gloves. Use of

cleaners containing chlorine, sodium or other acids will void the warranty.

5. Clean the burner sight glass and double check insulation around igniter.

6. Thoroughly clean the flame rod with scotch brite or similar cleaning pad.

Hot Surface I

nitor

Flame rod

Burner flan

e nuts

Energy Kinetics 51 Molasses Hill Road Lebanon, NJ 08833 800-323-2066 www.energykinetics.com

Page 2 of 3 – 10-1950 Rev. 10/18

Annual Tune Up & Inspection, Accel CS Boiler

Step 4 Reinstall Burner and Check Wiring

1. Inspect burner flange gasket and replace if necessary.

2. Reverse the removal instructions to reinstall the burner.

3. Using a thin blade screwdriver verify all the screws attaching the electrical

wiring on the connectors on the burner control, on the Condensing Manager,

and inside the electrical junction box are tight.

Step 6 Backflush Plate Heat Exchanger

1. Close valve (A) underneath the domestic hot water circulator.

2. Open drain valve above the circulator to backflush the heat exchanger.

3. If domestic water supply is “hard” (calcium or lime), consider installing Scale

Stopper (Item no. 10-0650).

4. Set temperature feeding hot water tank (above heat exchanger) by adjusting

ball valve (A) below the bronze circulator. Adjust the ball valve with the burner

running and a continuous flow of hot water from a fixture. You should be able

to briefly hold your hand on pipe (B).

Step 5 Check Condensate Parts

1. Remove boiler stand front cover. Clean the condensate trap. Verify that the

sealing ball is present inside of the trap.

2. Check the condensate neutralizer pH and for an adequate amount of

neutralizing chips, replace as needed.

Step 7 Check Zone Valves

Manually open and allow zone valves to close several times to see that they

move freely.

Energy Kinetics 51 Molasses Hill Road Lebanon, NJ 08833 800-323-2066 www.energykinetics.com

Page 3 of 3 – 10-1950 Rev. 10/18

Annual Tune Up & Inspection, Accel CS Boiler

Electronic Analyzer

Step 8 Start Burner & Check Combustion.

Check & Record:

Refer to manual for recommended settings.

1. Start appliance.

2. Check incoming gas pressure range: Natural Gas 3.5” – 10.5”w.c.

LPG 8” – 13”w.c.

Close manual gas shutoff valve. Open gas valve outlet pressure tap (A)

½ turn and connect a manometer hose over the port. Open gas shutoff

valve and test the pressure with the burner running at high fire and all

other gas appliances running so the reading is above the minimum

shown. Then verify that with no gas flow and the burner off and all

other gas appliances off that the maximum gas pressure does not

exceed the maximum shown above.

3. Ensure you have a sufficient heat (or hot water) demand to allow the

unit to run at full rate without shutting off on due to high temperature.

4. Run appliance at maximum fan speed (See Table in Boiler manual for

specific model). For newer systems: INFO button Test Forced

rate Set High Fire Start Test. For systems without this option:

INFO button Advanced Setup Modulation Config CH Max

Modulation Rate. Use left and right arrows only. To delete prior setting,

arrow to DEL and press OK repeatedly until cleared, and then use

arrows to enter maximum RPM.

5. Check that O2 reading is between 4.2% and 4.8% (4.5% target).

Adjust throttle screw (B) if necessary. Turn throttle screw clockwise to

increase O2 and counter clockwise to decrease O2.

6. Keep burner running until completely stabilized, make adjustment when

necessary.

7. Set appliance to minimum fan speed for offset adjustment with “Set

Low Fire” on most systems, or by adjusting the max modulation rate to

~ 50-100 RPM above the minimum modulation rate via “Modulation

Config” as shown in step 4.

8. Remove offset cap screw (C) with Torx T-40 screw driver or 5 mm hex

key.

9. Check that offset O2 reading is between 4.2% and 4.8% (4.5% O2

target). Adjust if necessary. Turn counter clockwise to increase O2 and

clockwise to decrease O2 reading. Adjust in very small increments, and

allow to stabilize between adjustments.

10.Repeat High Fire and Low Fire O2 tests until readings are stable with no

adjustments needed. If you are running out of time on the 5 minute

test, tap Stop Test twice quickly to restore another 5 minute session.

11.Press “Stop Test” for Forced Rate adjustments, or if modulation rate

set, reset the fan speed to maximum RPM (see Item 3 above). Verify

speed is at maximum RPM. To view current fan speed, press “Home”.

12.Perform carbon monoxide test two minutes after light off. If the carbon

monoxide exceeds 400 ppm air-free after two minutes of operation,

shut off boiler immediately and repeat "Prepare for Start Up" checklist

found in installation manual.

Step 9 Low Water Cutoff Test

1. Every year: Press “TEST” button on LWCO while burner is firing.

Confirm the “LOW WATER” LED turns on and the burner shuts off.

2. Every 5 years: Remove LWCO and clean sensing probe. Reinstall the

LWCO and confirm TEST and burner operation. Never use pipe dope

of any kind on plastic LWCO threads. Use only Teflon tape.

Venturi

Inhaltsverzeichnis

Andere ENERGY KINETICS Kessel Handbücher

ENERGY KINETICS

ENERGY KINETICS Resolute Boiler Beilage

ENERGY KINETICS

ENERGY KINETICS 90+RESOLUTE BOILER Montageanleitung

ENERGY KINETICS

ENERGY KINETICS Accel CS Bedienungsanleitung

ENERGY KINETICS

ENERGY KINETICS EK1 Frontier Bedienungsanleitung

ENERGY KINETICS

ENERGY KINETICS Ascent Combi Boilers Leitfaden

ENERGY KINETICS

ENERGY KINETICS Ascent Combi Montageanleitung

ENERGY KINETICS

ENERGY KINETICS EK2C Beilage

ENERGY KINETICS

ENERGY KINETICS System 2000 EK1 Frontier Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS Resolute RT Montageanleitung

ENERGY KINETICS

ENERGY KINETICS System 2000 Beilage

ENERGY KINETICS

ENERGY KINETICS Ascent Combi Montageanleitung

ENERGY KINETICS

ENERGY KINETICS RESOLUTE RT Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS SYSTEM 2000 Ascent Combi Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS System 2000 Frontier Bedienungsanleitung

ENERGY KINETICS

ENERGY KINETICS System 2000 Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS 90+RESOLUTE BOILER Bedienungsanleitung

ENERGY KINETICS

ENERGY KINETICS EK3 Frontier Kurzanleitung

ENERGY KINETICS

ENERGY KINETICS System 2000 Leitfaden

ENERGY KINETICS

ENERGY KINETICS 90+RESOLUTE BOILER Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS EK1 Frontier Service-Handbuch

ENERGY KINETICS

ENERGY KINETICS Ascent Combi Service-Handbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung