Enertech Bentone B 30A CN Technische Daten

Providing sustainable energy solutions worldwide

178 024 51

Installation- and maintenance instruction

B 30A CN

171 205 17 97-01

DESCRIPTION

COMPONENTS

1. Shrouded disc

2. Nozzle

3. Ignition electrodes

4. Nozzle assembly

5. Ignition cable

6. Ignition transformer

7. Control box

8. Reset button

9. Cover, inspection glass

10. Fan wheel

11. Motor

12. Photo cell

13. Nozzle assembly adjustment

14. Blast tube

15. Air adjustment

16. Air damper

17. Solenoidvalve

18. Air intake

19. Pump

Burner tube Oil capacity Output Recommended nozzle Recommended

kg/h kW Mcal/h Angle Danfoss Monarch Pump pressure

L 6,0-17,0 71-202 61-173 45° - 60° S, B, R, PLP 10-15 bar

The net calorific value of 11,86 kWh/kg for light oil has been used.

TECHNICAL DATA

Type designation B 30A

DIMENSIONS

OUTPUT RANGE AND NOZZLES RECOMMENDED

RECOMMENDEDNOZZLE

Because of different boiler types

existing on the market, with varying

combustion chamber designs, it is not

possible to state a definite spray angle

or spray pattern.

Note that the spray angle and the spray

patternchangewiththepumppressure.

175

382

ø108

372

220

281

303

ø108 35

160-190

Burner tube Length of burner tube Measure B

L 150 115

L Standard 222 187

L 350 315

171 235 02 01-01

ELECTRODE ADJUSTMENT

7,0-9,0

2,5-3,5 1,0-2,0

GENERAL INSTRUCTIONS

GENERALRULES

The installation of an oil burner should

be carried out in accordance with local

regulations. The installer of the burner

must therefore be aware of all

regulations relating to oil and combu-

stion.

Only oil suitable for the burner should

be used and then in combination with

a suitable oil filter before the oil pump

of the burner.

If the burner is replacing an existing

burner make sure that the oil filter is

replaced or cleaned. The installation

must only be undertaken by experien-

ced personnel. Care should be taken

by the installer to ensure that no

electrical cables or fuel/gas pipes are

trapped or damaged during installation

or service/maintenance.

INSTALLATION INSTRUCTIONS

General installation instructions ac-

company the burner and should be left

in a prominent place adjacent to the

burner.

ADJUSTMENT OF BURNER

The burner is from the factory pre-set to

an average value that must then be

adjusted to the boiler in question.

All burner adjustments must be made

inaccordance with boiler manufacturers

instructions.These must include the

checking of flue gas temperatures,

average water temperature and CO2or

O2concentration.

To adjust the combustion device, start

by increasing the air volume and the

nozzle assembly somewhat.When the

burner starts it is burning with excess

air and smoke number 0. Reduce the

nozzle assembly adjustment until soot

occurs, and then increase the

adjustment to make the soot disappear

again. Then the volume of air is reduced

until soot occurs and increased again

to reach a combustion free of soot.

By this procedure an optimum adjust-

ment is obtained. If larger nozzles are

used the preadjustment of both the air

volume and the nozzle assembly must

be increased.

A whistling sound may be heard which

can be eliminated or reduced as fol-

lows: Increase the nozzle assembly

adjustment somewhat. The CO2-con-

tent and consequently the air volume

will then be reduced.

CONDENSATION IN CHIMNEY

A modern burner works with less ex-

cess air and often also with smaller

nozzles than older models.

This increases the efficiency but also

the risk of condensation in the chimney.

The risk increases if the area of the

chimney flue is too large. The tempera-

ture of the flue gases should exceed

60°C measured 0,5 metres from the

chimney top.

Measures to raise the temperature:

Insulate the chimney in cold attics

Install a tube in the chimney

Install a draught regulator (dilutes the

flue gases during operation and dries

them up during standstill)

Increase the oil quantity

Raise the flue gas temperature by

removing turbulators, if any, in the

boiler.

PUMP ADJUSTMENT

See separate description.

171 305 46 06-01

ADJUSTMENT OF NOZZLE

ASSEMBLY

Loosen the screw G and adjust the

nozzle assembly by turning the screw

Max. capacity - Front position

Medium capacity - Middle position

Min. capacity - Rear position

AIR ADJUSTMENT

Loosen the stop screw B and turn the

knob along the scale to the position

wanted and tighten the screw. Check

the air adjustment by making a flue gas

analysis.

MAINTENANCE

The boiler/burner should be examined

regularly for any signs of malfunction

or oil leakage.

OIL SUPPLY

The oil line should be dimensioned in

accordance with the pump manu-

facturer´s instruction. In the suction

line to the burner a filter should be

mounted to prevent any particles in the

oil from reaching the burner. If the

installation consists of several burners

each one should have its own suction

line from the tank or a circulation sy-

stem should be used.

The temperature in the oil line should

be kept as constant as possible. Avoid

exposing the line to excessive cold

which may cause blockages of paraffin

deposits.

The oil pipe and electric cable should

be fitted so that the burner can be

placed on the floor for inspection of the

combustion device.

MAINTENANCE

Warning: Before doing any service switch off power at the main switch and cut off the oil supply.

Open the cover and disconnect the

connecting pipes by loosening screw

SERVICE OF BURNER HEAD

171 305 74 95-01

1. Loosen or swing out the burner

from the boiler.

2. Turn the blast tube to the left and

withdraw it.

ELECTRIC EQUIPMENT

OIL BURNER CONTROL: LOA21... / LOA24...

FUNCTION

1. Switch on operating switch and twin thermostat

The burner motor starts, an ignition spark is formed, the prepurge goes

on till the prepurge period expires and the solenoid valve opens (2).

2. Solenoid valve opens

Oil mist is formed and ignited. The photocell indicates a flame.

(1) The ignition spark goes out 15 s. after flame indication (LOA24.171...).

(2) The ignition spark goes out 2 s. after flame indication when the ignition

transformer is connected to terminal 7 (LOA24.173...).

3. The safety time expires

a. If no flame is established before this time limit the control cuts out.

b. If for some reasons the flame disappears after this time limit, the

burner will make an attempt to re-start.

3-4. Operating position

If the burner operation is interrupted by means of the main switch or the

thermostat, a new start takes place when the conditions in accordance

with point 1 are fulfilled.

The oil burner control cuts out

A red lamp in the control is lit. Press the reset button and the burner

re-starts.

Post-ignition

(2) If a post-ignition of 15 s. is wanted, move the ignition transformer from

terminal 7 to terminal 6 (LOA24.173...).

LIST OF COMPONENTS

A1 Oil burner control P1 Timemeter (optional)

A2 Twin thermostat R1 Photoresistor

F1 Fuse, max. 10A S3 Main switch

H1 Alarm lamp T1 Ignition transformer

H2 Signal lamp (optional) Y1 Solenoidvalve

M1 Burner motor

Mains connection and fuses in accordance with local regulations.

TECHNICALDATA

Pre-ignition time: 13 s

Pre-purge time: 13 s

(1) Post-ignition time: 15 s

(2) Post-ignition time: 2 s

Safety lock-out time: 10 s

Reset time after lockout: ≈ 50 s

Reaction time on flame failure: max. 1 s

Ambient temperature: from - 20 to +60°C

Min. current with flame established: 65 A

Max. photo current at start: 5 A

Enclosure: IP 40

(Under voltage proof only LOA24...)

CONTROL OF PHOTO CURRENT

Current through photo unit is measured with a d.c. ammeter (a moving coil

instrument connected in series with the photo unit).

171 415 16 04-01

WIRING DIAGRAM

(1)(2)

0113484

-0,5 10 30 74

-1,0 8 26 64

-1,5 7 22 54

-2,0 6 18 44

-2,5 4 14 34

-3,0 3 10 24

-3,5 2 6 14

-4,0 1 2 4

Two-pipe system

Height Pipe diameter

H ø6 mm ø8 mm ø10 mm

mmmm

Height Pipe diameter

H ø4 mm ø5 mm ø6 mm

mmmm

Height Pipe diameter

H ø6 mm ø8 mm ø10 mm

mmmm

4,0 21 67 100

3,5 20 63 100

3,0 19 59 100

2,5 17 55 100

2,0 16 51 100

1,5 15 46 100

1,0 13 42 100

0,5 12 38 94

Height Pipe diameter

H ø5 mm ø6 mm ø8 mm

mmmm

4,0 31 65 100

3,5 27 57 100

3,0 23 49 100

2,5 20 40 100

2,0 16 32 100

1,5 12 24 77

1,0 8 16 51

0,5 4 8 26

INSTRUCTIONS PUMP TYPE DANFOSS BFP 21 L5

COMPONENTS

1.Nozzle port G 1/8"

2.Pressure gauge port G 1/8"

3.Pressure adjustment, 4mm allen key

4.Cartridge filter

5.Vacuum gauge port G 1/8"

6.Return line G 1/4"

7.Suction line G 1/4"

8.Return plugg

9.Pressure gauge port G 1/8"

TECHNICALDATA

Viscosity range: 1,8-12,0 mm2/s

Pressurerange: 7-15 bar

Factory setting: 10 bar

Rated voltage of coil: 220/240V

50/60 Hz

Oil temperature: -10 to +70°C

1-pipe system 1-pipe system

SUCTIONLINETABLES

The suction line tables consist of

theoretically calculated values where

the pipe dimensions and oil velocity

have been matched so that turbulences

will not occur. Such turbulences will

result in increased pressure losses and

in acoustic noise in the pipe system. In

addition to drawn copper piping a pipe

system usually comprises 4 elbows, a

non-return valve, a cut-off valve and an

external oil filter.

The sum of these individual resistances

is so insignificant that they can be

disregarded. The tables do not include

any lengths exceeding 100 m as

experience shows that longer lengths

are not needed.

The tables apply to a standard fuel oil of

normal commercial quality according to

current standards. On commissioning

with an empty tube system the oil pump

should not be run without oil for more

than 5 min. (a condition is that the pump

is being lubricated during operation).

The tables state the total suction line

length in metres at a nozzle capacity of

10,0 kg/h. Max. permissible pressure at

the suction and pressure side is 2,0 bar.

PURGING

On 1-pipe systems it is necessary to

purge the pump. On 2-pipe systems

purging is automatic through the return

line.

With an underlying tank a 1-pipe-

system is not recommended

Two-pipe system

171 505 09 92-04

FUNCTION DANFOSS BFP 21 L5

When the oil pump is started, oil is

drawn from the suction connection (S)

through the filter (H) to the suction side

of the gear wheel (C).

The gear wheel then pumps oil to the

pressure side and the oil is put under

pressure.

The pressure is controlled and kept

constant at the set value by the

regulatingvalve(P1)with the diaphragm

(D).

The regulating valve (P1) distributes

the oil quantity supplied by the gear set

the return side of the pump (R).

The oil quantity utilized is determined

by the set pressure on the regulating

valve (P1) and the size of the oil nozzle

in the nozzle line.

The valve (P1) functions in the following

way:

- Whentheopeningpressurehasbeen

reached, the passage to the return

side opens.

against the return side (R) by means

of the diaphragm (D) and goes into

starting position.

This can be remedied by:

- Reducing the pump pressure.

- Reducing the oil quantity supplied

by using a smaller nozzle.

- Using a pump with a larger capacity.

- The diaphragm and the spring keep

the pump pressure constant at set

value.

- If the pump is overloaded, i.e. if you

try to get out more oil than the gear

set can supply under existing circum-

stances, the oil pressure falls below

the set value and the valve closes

REPLACEMENT OF CARTRIDGE

FILTER

HOW TO REMOVE CARTRIDGE

FILTER FROM PLUG

Unscrew the cartridge filter plug in the

cover by means of a 4 mm allen key

and withdraw the cartridge filter. If

necessary, put a screwdriver between

the cartridge filter and the plug and

turn the cartridge filter carefully until it

comes off. Reject the cartridge filter

and replace it by a new one. Press it

on to the plug. Ensure that the O-ring

is not damaged. Then fit the new

cartridge filter to the pump.

MOUNTING/DISMOUNTING RETURN PLUG

171 505 27 00-01

One pipe system Two pipe system

NOZZLE TABLE Pump pressure bar

171 505 44 00-01

The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.

BURNER WITH PREHEATER

Consider that on preheating the oil quantity is reduced by 5-20% depending on.

- Rise in temperature at the nozzle

- Design of nozzle

- Capacity (high capacity - small difference)

Gph 8 9 10 11 12 13 14 15

kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h

0,40 1,33 16 13 1,41 17 14 1,49 18 15 1,56 18 16 1,63 19 17 1,70 20 17 1,76 21 18 1,82 21 18

0,50 1,66 20 17 1,76 21 18 1,86 22 19 1,95 23 20 2,04 24 21 2,12 25 22 2,20 26 22 2,28 27 23

0,60 2,00 24 20 2,12 25 22 2,23 26 23 2,34 28 24 2,45 29 25 2,55 30 26 2,64 31 27 2,73 32 28

0,65 2,16 26 22 2,29 27 23 2,42 29 25 2,54 30 26 2,65 31 27 2,75 33 28 2,86 34 29 2,96 35 30

0,75 2,49 29 25 2,65 31 27 2,79 33 28 2,93 35 30 3,08 36 31 3,18 38 32 3,30 39 34 3,42 40 35

0,85 2,83 33 29 3,00 36 31 3,16 37 32 3,32 39 34 3,47 41 35 3,61 43 37 3,74 44 38 3,87 46 39

1,00 3,33 39 34 3,53 42 36 3,72 44 38 3,90 46 40 4,08 48 42 4,24 50 43 4,40 52 45 4,56 54 46

1,10 3,66 43 37 3,88 46 39 4,09 48 42 4,29 51 44 4,48 53 46 4,67 55 48 4,84 57 49 5,01 59 51

1,20 3,99 47 41 4,24 50 43 4,47 53 46 4,68 55 48 4,89 58 50 5,09 60 52 5,29 63 54 5,47 65 56

1,25 4,16 49 42 4,40 52 45 4,65 55 47 4,88 58 50 5,10 60 52 5,30 63 54 5,51 65 56 5,70 68 58

1,35 4,49 53 46 4,76 56 48 5,02 59 51 5,27 62 54 5,50 65 56 5,73 68 58 5,95 70 61 6,15 73 63

1,50 4,98 59 51 5,29 63 54 5,58 66 57 5,85 69 60 6,11 72 62 6,36 75 65 6,60 78 67 6,83 81 70

1,65 5,49 65 56 5,82 69 59 6,14 73 63 6,44 76 66 6,73 80 69 7,00 83 71 7,27 86 74 7,52 89 77

1,75 5,82 69 59 6,18 73 63 6,51 77 66 6,83 81 70 7,14 85 73 7,42 88 76 7,71 91 79 7,97 94 81

2,00 6,65 79 68 7,06 84 72 7,45 88 76 7,81 93 80 8,18 97 83 8,49 101 86 8,81 104 90 9,12 108 93

2,25 7,49 89 76 7,94 94 81 8,38 99 85 8,78 104 89 9,18 109 94 9,55 113 97 9,91 117 101 10,26 122 105

2,50 8,32 99 85 8,82 105 90 9,31 110 95 9,76 116 99 10,19 121 104 10,61 126 108 11,01 130 112 11,39 135 116

2,75 9,15 108 93 9,71 115 99 10,24 121 104 10,73 127 109 11,21 133 114 11,67 138 119 12,11 144 123 12,53 148 128

3,00 9,98 118 102 10,59 126 108 11,16 132 114 11,71 139 119 12,23 145 125 12,73 151 130 13,21 157 135 13,67 162 139

3,50 11,65 138 119 12,35 146 126 13,03 154 133 13,66 162 139 14,27 169 145 14,85 176 151 15,42 183 157 15,95 189 163

4,00 13,31 158 136 14,12 167 144 14,89 176 152 15,62 185 159 16,31 193 166 16,97 201 173 17,62 209 180 18,23 216 186

4,50 14,97 177 153 15,88 188 162 16,75 198 171 17,57 208 179 18,35 217 187 19,10 226 195 19,82 235 202 20,51 243 209

5,00 16,64 197 170 17,65 209 180 18,62 221 190 19,52 231 199 20,39 242 208 21,22 251 216 22,03 261 225 22,79 270 232

5,50 18,30 217 187 19,42 230 198 20,48 243 209 21,47 255 219 22,43 266 229 23,34 277 238 24,23 287 247 25,07 297 256

6,00 19,97 237 204 21,18 251 216 22,34 265 228 23,42 278 239 24,47 290 249 25,46 302 260 26,43 313 269 27,49 326 280

6,50 21,63 256 220 22,94 272 234 24,20 287 247 25,37 301 259 26,51 314 270 27,58 327 281 28,63 339 292 29,63 351 302

7,00 23,29 276 237 24,71 293 252 26,06 309 266 27,33 324 279 28,55 338 291 29,70 352 303 30,84 366 314 31,91 378 325

7,50 24,96 296 254 26,47 314 270 27,92 331 285 29,28 347 298 30,59 363 312 31,83 377 324 33,04 392 337 34,19 405 349

8,00 26,62 316 271 28,24 335 288 29,79 353 304 31,23 370 318 32,63 387 333 33,95 403 346 35,25 418 359 36,47 432 372

8,50 28,28 335 288 30,00 356 306 31,65 375 323 33,18 393 338 34,66 411 353 36,07 428 368 37,45 444 382 38,74 459 395

9,00 29,95 355 305 31,77 377 324 33,59 398 342 35,14 417 358 36,71 435 374 38,19 453 389 39,65 470 404 41,02 486 418

Inhaltsverzeichnis

Andere Enertech Kamin im Innenbereich Handbücher

Enertech

Enertech Nu-way MULTIPLEX ENERGYSTREAM ES Series Leitfaden

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung