Enlight SR2042 Bedienungsanleitung

2U Server Barebone

Quick Start Guide

www.enlightcorp.com

Index

1System Overview...................................................................................3

1.1 Front View..................................................................................................... 3

1.2 Back View..................................................................................................... 3

2Hardware Installation.............................................................................4

2.1 Remove Chassis Cover ................................................................................ 4

2.2 Server System Layout................................................................................... 4

2.3 Install Processor and Heat sink..................................................................... 5

2.3.1 To install the processor......................................................................................................5

2.3.2 To install the heat sink.......................................................................................................6

2.4 Install System Memory.................................................................................. 7

2.5 Install HDD.................................................................................................... 8

2.6 Install Power supply(Option)......................................................................... 9

3Raid Function Step ................................................................................9

3.1 SATA............................................................................................................. 9

3.1.1 Setup....................................................................................................................................9

3.1.2 To install the BC4000 Series RAID controller drivers in Windows 2003.................13

3.2 SCSI ........................................................................................................... 14

3.2.1 Setup..................................................................................................................................14

3.2.2 Install the Driver When You Install Windows...............................................................18

4OS Pre Installation Steps.....................................................................19

4.1 Speedy-In CD-Title Introduction.................................................................. 19

4.2 Windows install........................................................................................... 19

5Troubleshooting...................................................................................27

5.1 Power Supply.............................................................................................. 27

5.2 System Fans............................................................................................... 28

Figure 1-1 Front View

HDD Trays Floppy Disk Drive

HDD LEDs CD-ROM Drive

LEDs and Button Panel

Figure 1-2 Back View

Dual USB Port NIC1 Connector (RJ45)

PS/2 Mouse Port Serial Port

NIC2 Connector (RJ45) VGA Port

PS/2 Keyboard Port AC Power Connector

To remove the top cover:

Loosen the screw on the top of the

cover.

Press down the button as the arrow

shows.

Slide the cover toward the rear of

side horizontally as the arrow shows to

the back panel.

Figure 2-1 Lifting the cover from the chassis

Figure 2-2 System Top View

DIMM slots CD-ROM(Option)

Processors HDD Trays

System Fans Power Supply

Floppy Disk Expansion Slots

2.3.1 To install the processor

The location of the processor on the motherboard is shown as below:

Figure 2-3 Processor Location

Processor 1

Processor 2

If SINGLE processor is intended, always install the processor on the processor 1 socket

and for the location of processor 1 and processor 2, please refer to the above figure.

Unlock the socket by pressing the

lever sideways and lift it up to a

90°-100° angle.

Figure 2-4 Pressing the lever sideways

Carefully insert the processor into

the socket until it fits in place with the

marked corner matches the socket

corner near the end of the lever, while

making sure that the processor is

parallel to the socket.

Lock the socket by pushing down the

lever.

Figure 2-5 Inserting the processor into the socket

2.3.2 To install the heat sink

Rotate and pull up the two levers.

Figure 2-6 Pulling up the two levers

Place the heat sink on the top of the

installed processor.

Push down the levers.

Rotate them back until the clips click

on the heat sink indicating that it is

locked.

Figure 2-7 Placing the heat sink on top of the processor

When you insert the DIMM(s), you have to always start with DIMM B3, A3. Please refer to

the following table:

DIMM A1 B1 A2 B2 A3 B3

2 - - - - V V

4 - - V V V V

6 V V V V V V

Table 2-1 DIMM Installation Option

Unlock a DIMM socket by pressing

the retaining clips outward.

Figure 2-8 Pressing the retaining clips outward

Carefully insert the DIMM into the

socket until the retaining clips snap

back in place.

Figure 2-9 Inserting the DIMM into the socket

B3 A3 B2 A2 B1 A1

To open the HDD tray:

Turn the lock counterclockwise to

release the lever from the HDD.

Slide the released button to the

direction of the arrow, and the lever will

be lifted automatically.

Figure 2-10 Pressing the released button Slide the HDD assembly out of the

drive bay.

Figure 2-11 Sliding the HDD assembly out of the drive bay

To install the HDD:

Place the HDD to the HDD tray and

secure it with four screws as shown.

Figure 2-12 Securing the HDD to the HDD tray

Carefully insert the HDD assembly

into the bay with the lever lifted until it

completely enters the bay.

Figure 2-13 Inserting the HDD assembly into the bay

Push the levers back in place.

Turn the lock on the lever clockwise

to secure the HDD.

Figure 2-14 Pushing the levers back in place

)

To install the power supply:

Push the power supply right into the

tray until it completely enters the tray.

Figure 2-15 Putting the power supply into the tray

3.1.1 Setup

Step 1：To enter the BIOS Configuration Utility:

Turn on your computer to start

booting.

When prompted, type <CTRL+R>

to access the RAIDCore BIOS Array

Configuration Utility.

Step 2：To initialize disks from the BIOS:

Use the arrow keys to select

Initialize Disk(s) from the Main menu.

Press Enter.

Use the arrow keys to highlight a

disk, and then press the Insert key to

select the disk or choose all selectable

disks by pressing A.

Press Enter to initialize the selected

disks.

Press C to continue with initialization.

Step 3：To create an array:

Inhaltsverzeichnis

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung