Enovation Controls Murphy PowerView PV101-C Bedienungsanleitung
2013-04-08 00-02-0796
Catalog Section 78
PowerView
Model PV101-C
User’s Guide
Version 3.2
Table of Contents
Introduction...............................................................................1
Engine and Transmission Parameters....................................................................2
Faceplate Features .................................................................................................3
Navigation and Keypad Functions .......................................................................... 4
First Time Start Up ...................................................................8
Main Menu Options................................................................11
Go to 1-Up Display/Go to 4-Up Display ................................................................11
DPF Regen* ..........................................................................................................11
Selecting a Language ...........................................................................................13
Stored Codes ........................................................................................................14
Engine Configuration.............................................................................................14
Setup 1-Up Display ...............................................................................................14
Setup 4-Up Display ...............................................................................................17
Service Reminders ................................................................................................20
Select Units ...........................................................................................................22
Backlight Adjustment.............................................................................................22
Contrast Adjustment..............................................................................................22
Utilities Menu ..........................................................................23
Gage Data .............................................................................................................23
Remove All Gages ................................................................................................23
Software Version ...................................................................................................23
Fault Conversion ...................................................................................................24
Analog Input ..........................................................................................................25
Engine Speed Control ...........................................................................................25
OEM Menu ...............................................................................27
MODBUSSetup .................................................................................................27
CANBUS Data Rate ..............................................................................................28
Select Engine ECU ...............................................................................................29
Set Source Address ..............................................................................................30
Restore All Defaults ..............................................................................................30
Clear Machine Hours ............................................................................................30
Set Machine Hours................................................................................................30
Fuel Setpoints .......................................................................................................31
DPF Regen Menu ON/OFF...................................................................................31
ENG SPD CTRL Menu ON/OFF...........................................................................32
Faults and Warnings..............................................................33
Auxiliary Gage Fault ..............................................................................................34
Active Fault Codes ................................................................................................34
Derate / Shutdown Codes .....................................................................................35
Acknowledging Fault Codes .................................................................................36
Troubleshooting .....................................................................37
Additional Contact Information ...........................................42
In order to consistently bring you the highest quality, full
featured products, we reserve the right to change our
specifications and designs at any time. The latest version of
this manual can be found at www.fwmurphy.com.
Warranty - A limited warranty on materials and
workmanship is given with this Enovation Controls product.
A copy of the warranty may be viewed or printed by going to
www.fwmurphy.com/warranty
BEFORE BEGINNING INSTALLATION OF THIS
MURPHY PRODUCT:
•Disconnect all electrical power to the machine.
•Make sure the machine cannot operate during
installation.
•Follow all safety warnings of the machine
manufacturer.
•Read and follow all installation instructions.
00-02-0796 - 1 - 2013-04-08
Introduction
Congratulations on purchasing your PowerView display, a
multifunction tool that provides a window into the many
parameters and service codes of modern electronic engines
and transmissions.
This guide is intended to help you set up your PowerView
display and identify navigation basics and product features.
The display’s simple navigation and powerful features allow
you to quickly master the product.
Additional information can be found on our website at
www.fwmurphy.com/pv101/.
00-02-0796 - 2 - 2013-04-08
Engine and Transmission Parameters
The following are some of the engine and transmission
parameters which can be displayed in standard or metric
units as well as in English, Spanish, French, Italian or
German languages (when applicable, consult engine or
transmission manufacturer for SAE J1939 supported
parameters):
•Engine RPM
•Engine hours
•System voltage
•Percent engine load at
current RPM
•Coolant temperature
•Oil pressure
•Fuel economy
•Throttle position
•Engine manifold air
temperature
•Current fuel consumption
•Transmission oil
pressure
•Transmission oil
temperature
•Transmission gear
position
•Engine
configuration
parameters
•Active fault codes
•Stored fault codes
00-02-0796 - 3 - 2013-04-08
Faceplate Features
00-02-0796 - 4 - 2013-04-08
Navigation and Keypad Functions
The keypad on the PowerView display is a capacitive touch
sensing system. There are no mechanical switches to wear
or stick. The keys on the keypad perform the following
functions:
Menu – Enter or exit menu screens.
Left Arrow – Scroll the screen or move
the parameter selection to the left or
upward.
Right Arrow – Scroll the screen and
move the parameter selection to the right
or downward.
Enter Key – Select a menu or parameter
or hide/view an active fault code.
Inhaltsverzeichnis
Andere Enovation Controls Monitor Handbücher
Enovation Controls
Enovation Controls MURPHY PowerView PV500 Bedienungsanleitung
Enovation Controls
Enovation Controls Murphy PowerView PV485 Bedienungsanleitung
Enovation Controls
Enovation Controls MURPHY PowerView PV380-R3 Bedienungsanleitung
Enovation Controls
Enovation Controls MURPHY PowerView Bedienungsanleitung
Enovation Controls
Enovation Controls Murphy PowerView PV485 Bedienungsanleitung
Enovation Controls
Enovation Controls MURPHY PowerView PV1100 Bedienungsanleitung
Enovation Controls
Enovation Controls Murphy PowerView PV485 Bedienungsanleitung
