Enterasys WPIM-E1 Montage- und Wartungsanleitung
WPIM-E1
LOCAL MANAGEMENT GUIDE
WPIM-E1 LOCAL MANAGEMENT GUIDE
i
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS)ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
CAUTION: THE WPIM-E1 IS INTENDED TO BE INSTALLED IN TUV APPROVED
EQUIPMENT BY A QUALIFIED SERVICE PERSON. CHECK THE EQUIPMENT
OPERATION/INSTALLATION INSTRUCTIONSAND/OR EQUIPMENT MANUFACTURER TO
VERIFY/CONFIRMYOUR EQUIPMENT IS SUITABLE FOR INSTALLED APPLICATION
CARDS.
CAUTION: ALWAYS DISCONNECT THE E1 BOARD (THE ONE WITH THE TELEPHONE
PLUG/JACK) FROM THE TELEPHONE SYSTEM WHEN INSTALLING OR WHEN THE
COVERS ARE REMOVED FROM THE HOST PRODUCT.
Achtung:
Das WPIM-E1 Modul darf nur von qualifiziertem Service Personal in
TÜV-zugelassenen Geräten installiert werden. Vor dem Einbau muß in der Installationsanweisung
und Funktionsbeschreibung des Gerätes überprüft werden ob das Modul kompatible ist und
verwendet werden kann.
Achtung:
Die Verbindung zu dem E1-Modul (die Karte mit dem Telefonanschluß) muß bei
Installationen getrennt werden.
© Copyright 1996 by:
Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Part Number: 9031484-02 February 1996
BRIM
,
EMM-E6
,
MicroMMAC
and
NBR-620
are registered trademarks and
WPIM
is a trademark
of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
Printed On Recycled Paper
NOTICE
ii
WPIM-E1 LOCAL MANAGEMENT GUIDE
VCCI NOTICE
This equipment is in the 1st Class Category (information equipment to be used in commercial and/or
industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial
and/or industrial areas.
Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be
caused to radios and TV receivers, etc.
Read the instructions for correct handling
.
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT
: Before utilizing this product, carefully read this License Agreement.
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (the
“Program”) contained in this package. The Program may be contained in firmware, chips or other
media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
CABLETRON SOFTWARE PROGRAM LICENSE
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction
and venue of the New Hampshire courts.
NOTICE
WPIM-E1 LOCAL MANAGEMENT GUIDE
iii
EXCLUSION OF WARRANTY
AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including
its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOUBYCABLETRONIN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE
ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING
HARDWARE.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,
EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR
ON THE DURATION OR LIMITATION OF IMPLIED WARRANTEES IN SOME
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer
software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the
Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects
is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the
DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its
successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867.
WPIM-E1 LOCAL MANAGEMENT GUIDE
v
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1.1 USING THIS MANUAL................................................................1-1
1.2 GETTING HELP..........................................................................1-2
1.3 WPIM-E1 FEATURES.................................................................1-2
1.4 WPIM-E1 SPECIFICATIONS......................................................1-3
1.5 RELATED MANUALS..................................................................1-4
CHAPTER 2 LOCAL MANAGEMENT
2.1 THE WAN PHYSICAL CONFIGURATION SCREEN..................2-2
2.1.1 WAN Physical Configuration Screen Fields ...................2-2
2.1.2 WPIM-E1 Configuration Fields.......................................2-3
2.1.3 The WPIM Timeslot Configuration Table........................2-5
2.2 THE WAN INTERFACE CONFIGURATION SCREEN ...............2-7
2.2.1 WAN Interface Configuration Screen Fields...................2-8
2.3 FULL E-1 CONFIGURATION USING PPP ...............................2-10
2.3.1 WPIM-E1 Physical Configuration .................................2-11
2.3.2 WPIM-E1 Interface Configuration.................................2-12
2.4 FRACTIONAL E-1 CONFIGURATION USING PPP .................2-14
2.4.1 WPIM-E1 Physical Configuration .................................2-15
2.4.2 WPIM-E1 Interface Configuration.................................2-17
2.5 FRAME RELAY CONFIGURATION..........................................2-18
2.5.1 WPIM-E1 Physical Configuration .................................2-19
2.5.2 WPIM-E1 Interface Configuration.................................2-21
2.6 LEX CONFIGURATION.............................................................2-22
2.6.1 WPIM-E1 Physical Configuration .................................2-22
2.6.2 WPIM-E1 Interface Configuration.................................2-24
APPENDIX A WAN INTERFACE CABLE SPECIFICATIONS
APPENDIX B WAN TERMS AND ACRONYMS
WPIM-E1 LOCAL MANAGEMENT GUIDE
1-1
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems
WPIM-E1 Local Management Guide
.
This manual explains how to use Local Management to control and
manage the Cabletron Systems WPIM-E1. Appendix A of this guide
provides connector and pinout information for the WPIM-E1.
The WPIM-E1 resides in and provides connectivity/functionality to
Cabletron Systems Wide Area Network (WAN) modules such as the
BRIM-W6.
Before using this manual you must:
• Install the WPIM-E1 in a Wide Area Network module. Refer to the
appropriate manual (i.e., the
BRIM-W6 User’s Guide
) for
installation and troubleshooting procedures.
• Setup and access Local Management. Refer to the appropriate MIM,
standalone hub, or module User’s Guide for instructions on setting
up and accessing Local Management.
1.1 USING THIS MANUAL
Read through this manual completely to familiarize yourself with its
content and to gain an understanding of the features and capabilities of
the WPIM-E1.You should have a general working knowledge of the
following data communications networks and their physical layer
components before using the WPIM-E1.
•WAN
• Ethernet and IEEE 802.3
• Token Ring and 802.5
CHAPTER 1:
INTRODUCTION
1-2
WPIM-E1LOCALMANAGEMENT
The following list briefly explains each chapter of the WPIM-E1 manual:
Chapter 1,
Introduction
, outlines the contents of this manual, describes
WPIM-E1 features, lists specifications, and concludes with a list of
related manuals.
Chapter 2,
Local Management
, describes how to use Local Management
to setup the WPIM-E1.
Appendix A,
WAN Interface Cable Specifications
, provides Cabletron
part numbers and connector information for the interface cables used with
the WPIM-E1.
Appendix B,
WAN Terms andAcronyms
, is a brief glossary of the terms
used in this book.
1.2 GETTING HELP
If you need additional support related to the WPIM-E1, or if you have any
questions, comments, or suggestions concerning this manual, contact
Cabletron Systems Technical Support:
By phone ..........................(603) 332-9400
Monday-Friday; 8am - 8pm Eastern Time
By CompuServe...............GO CTRON from any ! prompt
By FTP.............................ctron.com (134.141.197.25)
Login:
anonymous
, Password:
your email address
1.3 WPIM-E1 FEATURES
The WPIM-E1 extends the functionality of your Wide Area Network
module to allow remote connectivity using WAN services such as E-1 or
Fractional E-1.
The WPIM-E1 provides an E-1 interface that includes a built-in Channel
Service Unit/Digital Service Unit (CSU/DSU) for direct connection to an
E-1 line. This WPIM supports both Full E-1 or Fractional E-1 using 56 or
64 Kbps timeslots.
WPIM-E1 SPECIFICATIONS
WPIM-E1 LOCAL MANAGEMENT GUIDE
1-3
WAN Protocols
As of this printing, the module in which the WPIM-E1 is installed
supports the following WAN protocols (refer to the Release Notes
included with the host MIM or standalone hub for a list of current
protocols):
• Point to Point Protocol (LCP ) as defined by RFC 1661
• Point to Point Protocol (BNCP) as defined by RFC 1638
• Point to Point Protocol LAN Extender (PPP/LEX)
• Frame Relay as defined by RFC 1490
MIB Support
Refer to the Release Notes included with the host MIM or standalone hub
for a list of all MIBs supported by the WPIM-E1. For information about
how to extract and compile individual MIBs, contact Cabletron Systems
Technical Support (see
Getting Help
).
1.4 WPIM-E1 SPECIFICATIONS
This section describes the environmental specifications and
safety/approval requirements for the WPIM-E1. Cabletron Systems
reserves the right to change these specifications at any time without
notice.
Environmental Requirements
Operating Temperature: +5
°
to +40
°
C (41
°
to 104
°
F)
Non-operating Temperature: -30
°
to +90
°
C (-22
°
to 194
°
F)
Operating Humidity: 5% to 95% (non-condensing)
Safety
This unit meets the safety requirements of EN60950.
EMI
This unit meets the EMI requirements of EN55022 Class A and
VCCI Class I.
CHAPTER 1:
INTRODUCTION
1-4
WPIM-E1LOCALMANAGEMENT
EMC
This unit meets the EMC requirements of EN50082-1 including
IEC 801-2 (ESD), IEC 801-3 (Radiated Susceptibility), and
IEC 801-4 (EFT/B).
1.5 RELATED MANUALS
Refer to the manual included with the host Wide Area Network module
(e.g., the
BRIM-W6 User’s Guide
) to supplement the procedures and
other technical data provided in this manual. Refer to the MIM,
standalone hub or module User’s Guides and/or Local Management
Guides for Local Management setup information. This manual references
procedures in these manuals, where appropriate, but does not repeat them.
It is the responsibility of the person who sells the system to
which the WPIM-E1 will be a part to ensure that the total
system meets allowed limits of conducted and radiated
emissions.
WARNING
WPIM-E1 LOCAL MANAGEMENT GUIDE
2-1
CHAPTER 2
LOCAL MANAGEMENT
This Chapter explains how to configure the WPIM-E1 through Local
Management. The
WAN Physical Configuration screen
and the
WAN
Interface Configuration screen
appear as Local Management menu
selections after you install the WPIM-E1 into a WAN module such as the
BRIM-W6 and then install the BRIM into a MIM or standalone hub.
Refer to the MIM or standalone hub User’s Guide for instructions about
how to setup and access Local Management.
Sections of this chapter include:
• The WAN Physical Configuration screen 2.1
• The WAN Interface Configuration screen 2.2
• Full T-1 Configuration Using PPP 2.3
• Fractional T-1 Configuration Using PPP 2.4
• Frame Relay Configuration 2.5
• LEX Configuration 2.6
Read Sections 2.1 and 2.2 to gain an understanding of the WPIM-E1
Local Management screens. Sections 2.3 through 2.6 provide examples
for setting up the WPIM-E1 for full or fractional E-1 in a PPP
environment, or for configuring the WPIM-E1 for LEX or Frame Relay.
Navigate through the WPIM Local Management Screens by
using the following keyboard commands:
SPACEBAR to toggle between selections in a field.
ENTER (RETURN) to implement a selection.
Arrow keys to move up, down or sideways within the screen.
TIP
Inhaltsverzeichnis
Andere Enterasys Extender Handbücher
Enterasys
Enterasys VHIM-2GSX-L3 Bedienungsanleitung
Enterasys
Enterasys RBT-AG-IA Bedienungsanleitung
Enterasys
Enterasys VHIM-2GT-L3 Bedienungsanleitung
Enterasys
Enterasys VHSIM-G6 Bedienungsanleitung
Enterasys
Enterasys WPIM-T1 Montage- und Wartungsanleitung
Enterasys
Enterasys VHIM-2GBC-L3 Bedienungsanleitung
