Enttec DMX USB PRO Mk2 Bedienungsanleitung

 DATASHEET – v2.1

ID: 5929715

1 |

DMX USB PRO Mk2 (70314)

Visit the ENTTEC website for the

latest version of this document

DMX USB Pro Mk2 – User Guide

The ultimate in DMX USB control.

The DMX USB Pro Mk2 is a USB -> DMX device capable

of sending or receiving up to 1024 DMX channels

through one simple USB 2.0 connection. It’s supplied

with a DB15 to DMX Dual DMX output cable to make

connection to your DMX / RDM lighting equipment

simple.

The DMX USB Pro Mk2 works with a broad array of

supported 3rd party software running on Windows,

Linux or MacOS. The Pro Mk2 features full backward

compatibility with software that supports the original

DMX USB Pro, to output a single universe.

A 1 universe DMX stream can be recorded using the

DMX input port; or using Art-Net and saved onto the

USB Pro Mk2’s internal memory for infinite looping or

for a fixed number of loops after powerup.

The Pro Mk2’s durable machined aluminum body

makes it well suited to life on the road and 1500V full

isolation for both data and power protect your

computer from any stray voltages on the DMX line.

The DMX USB Pro Mk2 features an internal frame

buffer for consistent DMX generation with perfect

timing without reliance on your computer’s

processor.

Features

 Two universes (512 channel each) of input or

output (one per DMX port).

 Fully compliant with USITT DMX512-A.

 RDM enabled (ANSI E1.20 compliant).

 Output refresh rate configurable from 1 to 40

FPS (Frames Per Second).

 Standalone mode: playback a single

recorded DMX show on power-up.

 Configurable MAB and Break time using

ENTTEC’s Pro Manager Software to

accommodate non-standard equipment.

 1500V full isolation (data & power lines to

protect your computer from surges on the

DMX line).

 Drivers for Windows, MacOS and Linux

(drivers released and maintained by FTDI).

 Compatible with various open-source and

professional lighting control programs.

 Backward compatibility with software that

supports ENTTEC’s DMX USB Pro.

 Developer API available to integrate into

your own software.

 USER GUIDE – v2.1ID:

5929745

2 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Content

Safety ............................................................................................................................................................................................................................ 3

Electrical safety ............................................................................................................................................................................................................................. 3

System planning and specification .................................................................................................................................................................................... 3

Protection from injury during installation ..................................................................................................................................................................... 3

Installation safety guidelines ................................................................................................................................................................................................ 4

Basic setup ................................................................................................................................................................................................................4

Functional features ............................................................................................................................................................................................... 5

Adjustable refresh rate ............................................................................................................................................................................................................. 5

RDM ..................................................................................................................................................................................................................................................... 5

Standalone ...................................................................................................................................................................................................................................... 5

Hardware features ................................................................................................................................................................................................. 5

LED status indicator ................................................................................................................................................................................................................... 6

PRO-Manager ........................................................................................................................................................................................................... 6

Devices .............................................................................................................................................................................................................................................. 7

Firmware update .......................................................................................................................................................................................................................... 7

Settings ............................................................................................................................................................................................................................................. 7

DMX send ......................................................................................................................................................................................................................................... 8

DMX receive ..................................................................................................................................................................................................................................... 8

Standalone mode ........................................................................................................................................................................................................................ 8

MIDI (legacy feature) .......................................................................................................................................................................................... 10

DMX ports ................................................................................................................................................................................................................. 11

DMX out ........................................................................................................................................................................................................................................... 11

DMX in .............................................................................................................................................................................................................................................. 11

DMX connector pin out ........................................................................................................................................................................................................... 11

Servicing, inspection & maintenance ......................................................................................................................................................... 11

Cleaning .......................................................................................................................................................................................................................................... 12

Package contents ................................................................................................................................................................................................. 12

Ordering information ......................................................................................................................................................................................... 12

 USER GUIDE – v2.1ID:

5929745

3 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Safety

Ensure you are familiarized with all key information within this guide and other relevant ENTTEC

documentation before specifying, installing, or operating an ENTTEC device. If you are in any doubt about

system safety, or you plan to install ENTTEC device in a configuration that is not covered within this

guide, contact ENTTEC or your ENTTEC supplier for assistance.

ENTTEC’s return to base warranty for this product does not cover damage caused by inappropriate use,

application, or modification to the product.

Electrical safety

 This device must be opperated in accordance with applicable national and local electrical and

construction codes.

 This device can be damaged by excess voltage outside the operating range defined within this products

datasheet.

 To reduce the risk of fire or electrical faults do not exceed the ratings and limitations defined in the

product datasheet or this guide.

 Ensure there are no opportunities for cables to short circuit and cabling cannot be snagged or pulled.

 Do not over stretch cabling to the device’s connectors and ensure that cabling does not exert force on

the PCB.

 Isolate your installation from power immediately if accessories power cables or connectors is in any

way damaged, defective, shows signs of overheating or are wet.

 Remove power from this product during cleaning or when it is not in use.

 Do not connect this device to a dimmer pack or mains electricity.

 Do not connect any of this devices V- or GND connectors to earth.

 Ensure your installation is protected from short circuits and overcurrent.

 Ensure all connections are complete and secure before providing power to the device.

System planning and specification

 To contribute to an optimal operating temperature, where possible keep this device out of direct

sunlight.

 This unit has an IP20 rating and is not designed to be exposed to moisture or condensing humidity.

 Ensure this device is only operated within the specified ranges within the product datasheet.

Protection from injury during installation

 Always use suitable personal protective equipment when installing ENTTEC products.

 Once installation is completed, check that all hardware and components are securely in place and

fastened to supporting structures if applicable.

 USER GUIDE – v2.1ID:

5929745

4 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Installation safety guidelines

 The device is convection cooled, ensure it receives sufficient airflow so heat can be dissipated.

 Do not cover the device with insulating material of any kind.

 Do not operate the device if the ambient temperature exceeds that stated in the device specifications.

 Do not cover or enclose the device without a suitable and proven method of dissipating heat.

 Do not install the device in damp or wet environments.

 Do not modify the device hardware in any way.

 Do not use the device if you see any signs of damage.

 Do not handle the device in an energized state.

 Do not crush or clamp the device during installation.

 Do not sign off a system without ensuring all cabling to the device and accessories has been

appropriately restrained, secured and is not under tension.

Basic setup

1. Install Drivers

DMX USB Pro MK2 communicates with a computer using FTDI D2XX drivers. These drivers enable the DMX

USB Pro MK2 to be compatible with a range of operating system including Windows, Mac and Linux

(including Raspberry Pi).

Visit FTDI website for the latest drivers and operating system installation support:

ftdichip.com/Drivers/D2XX.htm

Alternatively download ENTTEC PRO-Manager software which includes the driver setup for Windows or Mac

(up to OS 10.12) from the ENTTEC website.

Mac: In some cases, there might be a conflict with other drivers on the Mac, to resolve such conflicts, disable

the Mac “Serial drivers” or run FTDI’s ‘D2xxHelper’.

2. Connecting DMX USB Pro MK2

a. Connect the DMX USB Pro MK2 via the Mirco USB 2.0 port to the computer using the supplied USB

cable.

b. Attach the DB15 breakout connector to the Breakout port on the DMX USB Pro Mk2.

c. Using standard DMX cable, connect any DMX enabled fixtures to the DMX USB Pro Mk2.

3. Control Software

Load the control software of choice onto the computer. Choose between open-source (free) and

professional (paid) software. For a full list of ENTTEC recommended software, please visit the DMX USB Pro

Mk2 website.

Alternatively, use the DMX USB Pro Mk2 API to write custom software.

 USER GUIDE – v2.1ID:

5929745

5 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Functional features

Adjustable refresh rate

The DMX USB PRO Mk2 output settings can be configured using PRO-Manager. This allows for adjustments

in refresh rate and each DMX frames packet structure.

 DMX Output Refresh Rate (per sec): This can be set between 0 and 40. 40 is the Default.

 DMX Output Mark After Break (MAB in µsec): This can be set between 10 and 1355. 10 is the Default.

 Break Time (µsec): This can be set between 96 and 1355. 96 is the Default.

RDM

RDM (E1.20) is supported as standard on the DMX USB PRO Mk2.

Remote Device Management (RDM) is a protocol enhancement to USITT DMX512 that allows bi-directional

communication between the DMX USB Pro Mk2 and RDM compliant devices over a standard DMX line. This

protocol will allow configuration, status monitoring, and management of these devices.

Not all control software which has implemented the DMX USB Pro Mk2 as a device support RDM.

Standalone

The standalone mode built into the DMX USB Pro Mk2 allows the recording and playback of a DMX

sequence/show.

The DMX USB Pro Mk2 Standalone Mode is limited to 1 Universe only and can be configured using the PRO-

Manager software.

Recordings can be made either by using the DMX USB Pro Mk2’s DMX input or Art-Net though the connected

computers internal loopback IP address (127.0.0.1).

The DMX USB Pro Mk2 only records the changing frames, to maximum the length of the recording. With 512

channels (1 Universe) being recorded, with a frame rate of 40 fps with each frame being unique from the

previous, the maximum record length will be 100 seconds. If the number of channels or unique frames per

second are halved, this will double the maximum recording length.

The playback of the Standalone sequence/show can be triggered from within Pro Manager or on Power Up

of the DMX USB Pro Mk2

The DMX USB Pro Mk2 draws its power from the USB connection. The DMX USB Pro Mk2 doesn’t require a

computer connection during Standalone Playback. The DMX USB Pro Mk2 can be powered through a 5v USB

power adaptor, allowing the DMX USB Pro Mk2 to be powered from the mains.

Any DMX generated by software which will output on the DMX port that is outputting standalone mode will

stop playing the sequence/show and output DMX as directed by the software.

Hardware features

 2.0 micro USB for connection to a computer

 15-Pin breakout port

 1* 5-Pin Male XLR for DMX Input

 2* 5-Pin Female XLR for DMX Output

 LED status indicator

Included in the box:

 USER GUIDE – v2.1ID:

5929745

6 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

LED status indicator

DMX USB PRO Mk2 comes with a RGB LED indicator located on the top surface of the device (above the USB

connector). When in operation, the DMX USB PRO Mk2 led will change between a combination of these

states. The LED colour signifies the related activity:

Error Mode: If the LED status Indicator is steady Red, please do the following:

1. Disconnect and re-connect the USB cable to the DMX USB PRO Mk2.

2. Use ENTTEC’s PRO-Manager software to restore the device.

PRO-Manager

ENTTEC provides a free cross-platform app to configure, troubleshoot, test and update DMX USB PRO Mk2.

Pro-Manager is available to download from the ENTTEC website.

PRO-Manager runs inside a browser window and it opens the page by default. This can also be found within

a web browser by visiting: http://localhost:55555/.

From the PRO-Manager Home page, click the button (Find Devices) to search for DMX USB PRO Mk2

connected to the computer. When a device is detected, select it from the dropdown list.

After a device has been selected, the Devices Serial Number and Firmware version will be displayed in the

top Right of the screen.

Colour Description

Flashing White PRO Mk2 is powered on and idle

Steady Red Error Mode

Flashing Red Bad or unrecognisable API message

was received.

Steady Green DMX/RDM packet sent on port 1.

Flashing Green DMX/RDM packet received on port 1.

Steady Yellow DMX/RDM packet sent on port 2.

Flashing Yellow DMX/RDM packet received on port 2.

Steady Blue Standalone show is playing.

Steady Purple MIDI data sent MIDI output port.

(MIDI Breakout cable PN:79147

discontinued Q1 2021).

Flashing Purple MIDI data received on MIDI input port.

(MIDI Breakout cable PN:79147

discontinued Q1 2021).

 USER GUIDE – v2.1ID:

5929745

7 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Devices

Once the DMX USB PRO Mk2 is connected to PRO-Manager, the Devices tab gives a quick overview of the

selected device.

This will display:

 Devices Serial Number

 Devices Firmware version

 Device Type

 Device Capability

 Firmware Update

Firmware update

The Firmware update procedure can be used to:

 Update to the latest feature set.

 Reset DMX USB PRO Mk2 if it ever gets stuck or stops responding. (error mode).

The following steps will explain the firmware update procedure:

3. Within PRO-Manager Device Tab, at the bottom of the screen is a drop down to select a default firmware

option, or download a version from the ENTTEC website and locate it manually with ‘Choose File’.

4. After selecting the firmware file, click on the “Update Firmware” button and let the update proceed. Do

not remove the USB until the update is complete. The update progress is displayed on the webpage.

5. Once Finished, the page will automatically refresh, and device information will be updated to reflect the

updated firmware.

Settings

Once the DMX USB PRO MK2 is connected to PRO-Manager, the Settings tab allows the adjustment of the

DMX output parameters to accommodate for equipment that fall outside of the USITT DMX512-A standard.

The following parameters can be adjusted:

 DMX Output Refresh Rate (per sec): This can be set between 0 and 40. 40 is the Default

 DMX Output Mark After Break (MAB in µsec): This can be set between 10 and 1355. 10 is the Default

 Break Time (µsec): This can be set between 96 and 1355. 96 is the Default

 USER GUIDE – v2.1ID:

5929745

8 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

DMX send

PRO-Manager can be used to test the output of the DMX USB Pro Mk2. The test output can be sent in the

following ways:

 “Test Patterns” and select one of a the pre-programmed test patterns to test the DMX output

 “Live Art-Net” which will start listening for an Art-Net Broadcast though the loopback IP address

(127.0.0.1).

 “From Faders” and drag the desired channels fader to test the DMX output.

The output can then be verified using either DMX enabled

equipment or by using a DMX tester

While DMX is being output, the LED will blink to signify which

DMX port is being used to output.

DMX Send is not designed as a Lighting Control software, it’s

designed as a troubleshooting tool. After testing, PRO-

Manager will need to be closed, before opening the preferred

lighting control software. The DMX USB Pro Mk2 will only be

recognised by one software at a time, as the software latches

onto the USB port.

DMX receive

This tab will show a snapshot of the DMX values received through the 5-Pin Male XLR. Refresh the window

to see the updated values.

Standalone mode

The standalone mode built into the DMX USB Pro Mk2 allows the recording and playback of a DMX

sequence/show.

The DMX USB Pro Mk2 Standalone Mode is limited to 1 Universe only and can be configured using the PRO-

Manager software.

Recordings can be made either by using the DMX USB Pro Mk2’s DMX input or Art-Net though the connected

computers internal loopback IP address (127.0.0.1).

The DMX USB Pro Mk2 only records the changing frames, to maximum the length of the recording. With 512

channels (1 Universe) being recorded, with a frame rate of 40 fps with each frame being unique from the

previous, the maximum record length will be 100 seconds. If the number of channels or unique frames per

second are halved, this will double the maximum recording length.

The playback of the Standalone sequence/show can be triggered from within Pro Manager or on Power Up

of the DMX USB Pro Mk2

The DMX USB Pro Mk2 draws its power from the USB connection. The DMX USB Pro Mk2 doesn’t require a

computer connection during Standalone Playback. The DMX USB Pro Mk2 can be powered through a 5v USB

power adaptor, allowing the DMX USB Pro Mk2 to be powered from the mains.

 USER GUIDE – v2.1ID:

5929745

9 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

Any DMX generated by software which will output on the DMX port that is outputting standalone mode will

stop playing the sequence/show and output DMX as directed by the software.

Recording Options:

Below is a guide to the recording process.

 Show Name: Name to identify the show being recorded

 DMX Channels: The number of channels to record per DMX Frame (less channels = longer duration of

recording)

 Play Count: Total number of times the show is played back (from 1 to Forever).

 Loop Delay: The number of seconds delay, between each Loop playback.

 Play on Power-Up: If selected as “YES”, recorded show plays on power-up (this option is required to be

selected for true standalone operation).

 Output Port: The DMX Port to output the show. (Only one Port [single universe) is allowed).

 Input: Choose between a DMX input using the DMX Male connector on the breakout cable or Art-Net

though the connected computers internal loopback IP address (127.0.0.1)..

o Art-Net Universe: If Art-Net is set as the Input. Then an Art-Net Universe will need to be specified.

 Recording Control: By enabling Recording Control, and selecting the Trigger Channel and respective

value, it will only record whilst the trigger is active. Once the selected trigger channel and value is not

sent anymore, the recording will stop automatically. It will still need to be manually stopped to proceed

to next step of recording.

Start Recording

Initially the sequence/show is recorded to a binary file, that is saved onto the connected computer in a

location shown under the progress window.

Recording begins, only when the first frame is captured. Recorded frames as counted, are shown and an

estimate of the memory usage is also shown via the progress bar. The recording will stop automatically if

all memory has been used.

While recording from Art-Net, the DMX is also output on selected DMX Port and serves as a preview of the

recording. Whilst recording from DMX input, the DMX will not be output during the recording.

Once the recording process has finished, click on “Stop recording”. Once the recording has been stopped,

 USER GUIDE – v2.1ID:

5929745

10 |

DMX USB Pro Mk2 (70314)

Visit the ENTTEC website

for the latest version

click on “Write to Memory” button. This will then load the show file on to the memory of DMX USB PRO Mk2

and the progress is shown on the page. It is important, not to interrupt the memory load process, as it

might corrupt the show. Please wait till the upload progress finalises.

Once complete, the page will reload and will display the Standalone Show Control window.

Standalone show control:

This page will display information based on the current sequence/show which has been recorded based

on the settings set during the record process. Below is a guide to the Playback control.

 Play Icon: This will start the Standalone Mode playback

 Stop Icon: This will stop the Standalone Mode playback

 Record Icon: This will wipe the current Standalone sequence/show and allow a new sequence/show to

be recorded

 Export Show to File: This will download the sequence/show on the DMX USB PRO Mk2 to a binary file to

a computer connected to the DMX USB Pro Mk2. This file can then be transferred to another computer

if required.

 Import Show to DMX USB Pro Mk2: This will import the sequence/show on the DMX USB PRO Mk2 from

a binary file on the computer connected to the DMX USB Pro Mk2. This export/import process allows

the duplication of a showfile onto multiple DMX USB Pro Mk2 devices.

 Delete Show: This will delete the current sequence/show from the DMX USB Pro Mk2, ready for a new

sequence/show to be recorded.

MIDI (legacy feature)

The DMX USB PRO Mk2 has the capacity to support the legacy ‘DMX + MIDI accessory cable (pn: 79147)’.

discontinued Q1 2021. This is a non-class compliant MIDI implementation included as part of the DMX USB

Pro Mk2’s MIDI API.

PRO-Manager provides the ability to send test MIDI notes and display received MIDI data with this legacy

function.

Andere Handbücher für DMX USB PRO Mk2

Inhaltsverzeichnis

Andere Enttec Computerhardware Handbücher

Enttec

Enttec STORM 24 Gebrauchsanweisung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung