Environmental potentials EP-2000 DIN Handbuch

www.ep2000.com •800.500.7436

Power Quality For e Digital Age

Installation and Maintenance Manual

EP-2000 DIN

EP Technical Support: techsupport@ep2000.com • 800.500.7436

Mailing Address: 1802 N. Carson Street, Suite 108-2132, Carson City, NV 89701

FIVE YEAR WARRANTY

• Environmental Potentials will replace or repair EP-2000 DIN as long as it was not

damaged during installation or damaged from faulty installation.

• EP warranty registration card must be ﬁlled out and received by Environmental

Potentials within 15 days of installation.

• is warranty is for the repair or replacement of damaged EP products only.

Environmental Potentials accepts no liability, written or expressed, for the damage

that may have occurred to any other equipment; nor does Environmental Potentials

warranty cover any labor cost associated with replacement of such product.

Table of Contents

3 – Safety First

3 – Pre-Installation Preparations

4 – Wiring for loads 15 Amps or less

5 – Wiring for loads greater than 15 amps

6 – Wiring for DC Applications

EP-2000 DIN

Installation and Maintenance Manual

EP-2000 DIN INSTALLATION GUIDE

4EP-2000 DIN INSTALLATION GUIDE

Wiring for loads 15 Amps or less:

1. Screw in the input neutral from the incoming neutral source to screw terminal number 1.

2. Screw in the input phase from the incoming power source to screw terminal number 4.

3. Screw in the output neutral to screw terminal number 2 and connect to the input neutral terminal of the load.

4. Screw in the output phase to screw terminal number 5 and connect it to the input phase terminal of the load.

PLC Power Supply

DIN RAIL

Input Voltage

1 2 3 4 5

HOT

NEUTRAL

L 3

L 2

L 1

CAUTION – Ungrounded power systems are inherently unstable and can produce excessively high line-

to-ground voltages during certain fault conditions. During these fault conditions any electrical equipment,

including an SPD, may be subjected to voltages which exceed their designed ratings. is information is being

provided to the user so that an informed decision can be made before installing any electrical equipment on

an ungrounded power system.

EP-2000 DIN INSTALLATION GUIDE5

Wiring for loads greater than 15 amps:

1. Screw in the input neutral from the incoming neutral source to screw terminal number 1.

2. Screw in the input phase from the incoming power source to screw terminal number 4.

3. Screw in the input neutral from the incoming neutral source to the incoming neutral terminal of the load.

4. Screw in the input phase from the incoming power source to the incoming phase terminal of the load.

PLC Power Supply

Load at Greater than 15A

DIN RAIL

Input Voltage

1 2 3 4 5

HOT

NEUTRAL

L 3

L 2

L 1

*Do not install on loads greater than 25 amps

*also use this install method if the output wire size is larger than AWG#12

CAUTION – Ungrounded power systems are inherently unstable and can produce excessively high line-

to-ground voltages during certain fault conditions. During these fault conditions any electrical equipment,

including an SPD, may be subjected to voltages which exceed their designed ratings. is information is being

provided to the user so that an informed decision can be made before installing any electrical equipment on

an ungrounded power system.

EP-2000 DIN INSTALLATION GUIDE 6

PLC POWER SUPPLY

DIN RAIL

Output Voltage 1 2 3 4 5

NEGATIVE (-)

POSITIVE (+)

Wiring for DC Application:

1. Screw in the input (+) DC from the incoming (+) DC source to screw terminal number 1.

2. Screw in the input (-) DC from the incoming power source to screw terminal number 4.

3. Screw in the output (+) DC to screw terminal number 2 and connect to the input (+) DC terminal of the load.

4. Screw in the output (-) DC to screw terminal number 5 and connect it to the input (-) DC terminal of the load.

CAUTION – Ungrounded power systems are inherently unstable and can produce excessively high line-

to-ground voltages during certain fault conditions. During these fault conditions any electrical equipment,

including an SPD, may be subjected to voltages which exceed their designed ratings. is information is being

provided to the user so that an informed decision can be made before installing any electrical equipment on

an ungrounded power system.

Inhaltsverzeichnis

Andere environmental potentials Stromverteilungseinheit Handbücher

environmental potentials

environmental potentials EP-2000 Series Handbuch

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung

environmental potentials EP-2000 DIN Handbuch

Beliebte Stromverteilungseinheit Handbücher anderer Marken