Envision G218a1 Bedienungsanleitung
G218a1
Operation Instructions
Thank you for purchasing this monitor, a high-resolution multi-scan color
monitor.
Please read this guide thoroughly before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
WARNING: (FOR FCC CERTIFIED MODELS)
This monitor has been tested and found compliant with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide proper protection against harmful interference to a
residential installation. This monitor generates, uses, and can radiate radio
frequency energy. Harmful interference to radio communication may be led
as a result if it‘s not properly installed and used. However, there is no
guarantee that interference will not occur in a particular installation. If this
monitor does cause serious interference to radio or television reception,
resetting the monitor may determine it. Moreover, users are encouraged to
correct interference by doing one or more of the following:
Reorient or relocate the receiving antenna.
Move the monitor and the receiver further away from each other.
Connect the monitor into an outlet on a circuit different from that to
which the receiver is connected.
Consult your local dealer or an qualified technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded
power supply cord and the provided shielded video interface cable with
bonded ferrite cores. Also, any unauthorized changes or modifications to
this monitor would void the user‘s authority to operate this device.
Note: If necessary, shielded interface cables and AC power cord must be
used to meet the emission level limits.
English
Content
Safety Precautions.............................................................................1
First Setup .........................................................................................2
Quick Installation.............................................................................2-5
Rear View of the Product .................................................................. 6
Front View of the Product .................................................................. 6
Using On Screen Display (OSD) Functions ....................................7-9
Supporting Timing Modes .................................................................10
Technical Information........................................................................11
Care and Maintenance.....................................................................12
Troubleshooting ...............................................................................12
English
Safety Precautions
This monitor is manufactured and tested on a ground principle that a user’s
safety comes first. However, improper use or installation may result danger
to the monitor as well as to the user. Carefully go over the following
WARNINGS before installation and keep this guide handy.
WARNINGS:
This monitor should be operated only at the correct power sources
indicated on the label on the rear end of the monitor. If you’re unsure of
the power supply in your residence, consult your local dealer or power
company.
Do not try to repair the monitor yourself as it contains no
user-serviceable parts. The monitor should only be repaired by a
qualified technician.
Do not remove the monitor cabinet. There is high-voltage parts inside
that may cause electric shock to human bodies, even when the power
cord is disconnected .
Stop using the monitor if the cabinet is damaged. Have it checked by a
service technician.
Put your monitor only in a clean, dry environment. Unplug the monitor
immediately if gets wet and consult your service technician.
Always unplug the monitor before cleaning it. Clean the cabinet with a
clean, dry cloth. Apply non-ammonia based cleaner onto the cloth, not
directly onto the glass screen.
Keep the monitor away from magnetic objects, motors, TV sets, and
transformer.
Do not place heavy objects on the cable or power cord.
1
For PLUG CABLE EQUIPMENT, the Socket-outlet shall be installed
near the equipment and shall be easily accessible.
English
First Setup
Congratulation for purchasing this monitor of high performance!
This monitor comes with the following accessories:
Power Cable
D-Sub Cable (15 pin)
DVI Cable (24 pin)
Audio Cable
User’s Guide
Quick Start Guide
Warranty Documents
Quick Installation
Installing & Removing the Base
Install Remove
2
English
3
Preparing To Install The Optional Wall Mount Arm (Not
Included)
English
This monitor can be attached to a wall mounting arm you can purchase separately.
Turn the power OFF then dis-connect the cables from the monitor before performing
the procedure below. Lay the monitor face down on a soft surface.
1. Remove the base. It is attached to the stand by hooks.
2. Remove the 4 screws holding the stand to the hinge.
3. Remove the stand.
4
English
Attaching The Optional Wall Mount Arm (not supplied)
Follow these steps to finish installing the wall mounting arm:
1. Place the wall mounting arm onto the back of the monitor. Line up the
holes of the arm with the holes in the back of the monitor.
2. Insert the 4 screws into the holes and tighten.
3. Reconnect the cables. Refer to the user’s manual that came with the
optional wall mounting arm for instrucstions on attaching it to the wall.
NOTE
The ENVISION G218a1 is in compliance with the most current revision of the VESA
100mm Flat Panel Monitor Physical Mounting Interface (FPMPMI standard).
Connecting the Monitor
1. Connect Power Cable
Connect the power cable to the back of the monitor. Plug the power cable to a
nearby power outlet.
2. Connect Analog video cable (D-Sub cable)
Make sure both monitor and computer are powered OFF. Connect the video
cable ( D-Sub cable) to the computer, then to the monitor.
3. Connect DVI cable (Optional)
Connect the DVI cable from DVI output of computer to the DVI input of the
monitor.
4. Connect audio cable
Connect one end of the audio cable to the back of the monitor and connect the
other end to the computer’s audio out port.
5. Power-ON computer and monitor
Power-ON the computer, then Power-ON the monitor.
6. Windows users: Setting the Timing Mode (Resolution and Refresh Rate)
Example: 1680 x 1050 @ 60 Hz (Recommended Resolution)
Resolution Right-click on the Windows desktop > Properties > Settings >
“Desktop Area”. Set the resolution.
Refresh Rate (vertical frequency) See your graphic card’s user guide for
instructions.
Connection Diagram:
5
English
Rear View of the Product
➐➑➒ ➓
➐ POWER INPUT ➒ DVI INPUT (DVI 24 PIN)
➑ AUDIO INPUT ➓ VGA INPUT (D-SUB 15 PIN)
Front View of the Product
➊ ➋➌➍ ➎ ➏
➊ OSD TURN ON/OFF ➍ CONFIRMSELECTION
➋ SCROLL DOWN/DECREASE ➎ POWER ON/OFF
➌ SCROLL UP/INCREASE ➏ LED INDICATOR
6
English
Using On Screen Display (OSD) Functions
Display main menu.1
Exit from OSD menu.
Auto adjust the image when not in main menu.2
Confirm the selection.
Select the desired item when in OSD menu.Vor W
When not in OSD menu, it is to immediately activate Contrast/
Brightness. It should be changedto Contrast/ Brightness by pressing
button or .
▼+ ▲Recall both of Contrast and Brightness.
1 + ▼Power Lock (when not in OSD menu)
1 + ▲OSD Lock (when not in OSD menu)
Main Menu
7
English
V W
Inhaltsverzeichnis
Sprachen:
Andere Envision Monitor Handbücher
Envision
Envision H190L Bedienungsanleitung
Envision
Envision Envision Professional G22LWK Bedienungsanleitung
Envision
Envision EN-5100e Bedienungsanleitung
Envision
Envision EN-7100s Bedienungsanleitung
Envision
Envision H962w Bedienungsanleitung
Envision
Envision EN-7500 Bedienungsanleitung
Envision
Envision EFT920 Bedienungsanleitung
Envision
Envision H976WDL Bedienungsanleitung
Envision
Envision P2071L Bedienungsanleitung
Envision
Envision H1981 Bedienungsanleitung
Envision
Envision EN7400e Bedienungsanleitung
Envision
Envision G2016wa1 Bedienungsanleitung
Envision
Envision EN9110 Bedienungsanleitung
Envision
Envision G917w Bedienungsanleitung
Envision
Envision H22W Bedienungsanleitung
Envision
Envision Envision H1781 Bedienungsanleitung
Envision
Envision G2460w Bedienungsanleitung
Envision
Envision G918w1 Bedienungsanleitung
Envision
Envision G19LWK Bedienungsanleitung
Envision
Envision G912WA2 Bedienungsanleitung
