EPH Controls EMBER GW01 Bedienungsanleitung
GW01 GATEWAY
INSTRUCTIONS
Welcome
Thank you for choosing EMBER by EPH Controls. We hope you enjoy
using it as much as we did developing it!
Controlling your heating anywhere, anytime is only a few simple steps
away.
In this booklet, we will provide a step by step guide to setting up the
EMBER heating control app and its associated hardware.
Again, thank you for choosing EMBER.
View this insutruction online www.ephcontrols.com/ember
4
Get Started (Router requirements / Phone software)
5
LCD / LED / Button Legend
7
Paring your Programmer to your Gateway
9
Paring your Thermostats to your Programmer
11
Downloading the EMBER App
16
Pairing your Gateway to your wirelss internet
27
Zone Control diagram
21
Home setup
Table of contents
4
WiFi Requirement
The SSID of your Wi-Fi should not
be hidden when you are pairing the
gateway to your router.
Please install the gateway in a place
with a good Wi-Fi signal.
The GW01 gateway operates on
2.4GHz. It does not support 5GHz.
The MAC address of gateway should
not be in the blacklist of the router.
Please restart your wireless router
periodically or restart it before you
are going on holiday to ensure that
the connection is kept after long
periods of inactivity.
Pay attention to the number of
devices connected to your wireless
router. Some routers may not work
properly if too many devices are
connected.
Device Operating System
1) Minimum iOS is 9.
2) Minimum Android OS is 5.1
(Lollipop)
Positioning of the gateway
The gateway should be located near
the programmer in an area with
good WiFi signal. It should not be
installed close to appliances such as
microwaves, televisions etc.
The above will ensure a stable
connection for remotely controlling
your heating system.
Getting Started
Useful Information:
Visit EMBER YouTube channel
for the PS Set up Guide.
On the Initial Setup screen, click on the
Setting icon to access Tutorials, FAQs
and Videos.
5
LCD / LED / Button Legend
WPS / Smartlink
button
Function
button
Figure (5-a): The gateway
LED Status
Red LED on Gateway not connected to WiFi
Green LED on Gateway connected to WiFi
Red & Green LEDs On WiFi connection issue. Reset router.
Gateway
6
Figure (5-b): The RF programmer
Buttons to be used during gateway installation
LCD / LED / Button Legend
Programmer
7
Pairing your programmer to your gateway
Complete this step before pairing your thermostats to your programmer
1. Reset your router by switching it
o and on.
2. On the Programmer, press the
button for 5 seconds.
3. ‘Wireless Connect’ will appear on
the screen. Figure (6-a)
4. Press the button for 3
seconds. You will now enter the
gateway connection screen.
5. A four digit code will alternate
on the screen. Figure (6-b)
6. On the Gateway, press and hold
the ‘Function’button for 10
seconds.
7. Red and green LEDs on
the gateway will both ash
simultaneously every 1 second.
8. On the Programmer –‘r1’
appears on the screen.
Figure (6-c)
9. Wait for the LEDs on the gateway
to stop ashing.
10. Press the button.
Figure (6-a): ‘Wireless Connection’ screen
Figure (6-b): ‘Gateway Connection’ screen
Figure (6-c): ‘Gateway Connection’ screen
8
Note
If ‘r2’,‘r3’or ‘r4’ appears on the screen and you are not setting up a multi
programmer system, please reset the RF connections to the gateway by
completing the following:
Press and hold the crystal button until it begins to ash.
Press the Smartlink / WPS button once.
The LEDs will stop ashing for 5 seconds.
Once the LEDs begin to ash again, press the crystal button 3 times.
This will reset all RF connections to the gateway.
You can now complete steps 2 – 9 on the previous page.
Pairing your programmer to your gateway
Complete this step before pairing your thermostats to your programmer
9
1. Lower the cover on the front
of the RF programmer. Move
the selector switch to the ‘RUN’
position.
RUN
CLOCK
SET
PROG
SET
2. On the RF programmer, press the
button for 5 seconds. Wireless
Connect will appear on the
screen. Figure (7-a)
3. On the RFR wireless room
thermostat or RFC wireless
cylinder thermostat, press
the ‘Code’button. This is
located inside the housing
on the Printed Circuit Board.
Figure (7-b)
4. On the RF programmer, the
available zones will begin to ash.
5. Press the
ZONE SELECT
button for
the zone you wish to connect the
thermostat to.
6. The wireless symbol appears
on the screen.
Figure (7-a): ‘Wireless Connection’ screen
Reset button
Code button
Figure (7-b): Printed Circuit Board
Pairing your thermostats to your programmer
Complete this step before pairing your thermostats to your programmer
10
Figure (7-c) Zone screen
Pairing your thermostats to your programmer
Complete this step before pairing your thermostats to your programmer
7. The thermostat will count to 3
and then display the zone of the
programmer that it is paired to. If
it is paired to the rst zone it will
display r1, the second zone r2 etc.
Figure (7-c)
8. Press the wheel on the
thermostat to complete the
pairing process.
9. The RF programmer is now
operating in the wireless mode.
The temperature of the wireless
thermostat is now displayed on
the programmer.
10. Repeat this process for the
second, third and fourth zone if
required.
Inhaltsverzeichnis
Andere EPH Controls Tor Handbücher
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
