EPOX EP-MVP3G-M Bedienungsanleitung

1. The "LOAD SETUP DEFAULTS" function loads the system default data directly

from

ROM and initializes the associated hardware properly. This function is necessary

when you accept this mainboard, or the system CMOS data will corrupt.

LOAD SETUP DEFAULT

Read me first

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

Load SETUP Default (Y/N)? Y

STANDARD CMOS SETUP SUPERVISOR PASSWORD

BIOS FEATURES SETUP USER PASSWORD

CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION

POWER MANAGEMENT SETUP HDD LOW LEVEL FORMAT

PNP/PCI CONFIGURA ETUP

INTEGRATED PERIPH SAVING

LOAD SETUP DEFAULTS

ESC: QUIT :SELECT ITEM

F10:Save & Exit Setup (Shift)F2 :Change Color

Load Setup Defaults Except Standard COMS SETUP

2. KBPO(KeyBoard Power On) Function : There is a basic requirement that the

" +5V SB" power of the ATX power supply must be > = 0.1A (100mA).

Please refer to chapter 2-5 for detail.

EP-MVP3G-M

ISA/PCI/AGP

MainBoard

with Onboard PCI IDE and Super Multi-I/O.

Apollo MVP3 AGPset

The specification is subject to change without notice.

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

V040

Components Checklist

Please check your package which should include all items listed below. If you

find any item damaged or missed, please contact your supplier.

üü

üA. (1) One mainboard

üü

üB. (1) One user’s manual

üü

üC. (1) Floppy ribbon cable

üü

üD. (1) IDE ribbon cables

E. (2) PS/2 to AT keyboard connector adapter (optional)

üü

üF. (1) Ultra_DMA IDE driver diskette

(1) AGP Drivers

USERS

MANUAL

EP-MVP3G-M

2 1

28 27

Contents

page

Chapter 1 - Introduction................................................... 1-1

Chapter 2 - Hardware Design........................................... 2-1

2-1 Mainboard Layout .......................................................... 2-1

2-2 Connectors and Jumpers ................................................. 2-3

2-3 System Memory Configuration....................................... 2-5

2-4 ATX Power ON/OFF Control ......................................... 2-6

2-5 External Modem Ring-in Power ON and Keyboard Power

ON Functions ................................................................. 2-7

2-6 Integrated PCI Bridge ..................................................... 2-8

Chapter 3 - Award BIOS Setup........................................ 3-1

3-1 Standard CMOS Setup.................................................... 3-2

3-3 BIOS Features Setup....................................................... 3-2

3-3 Chipset Features Setup.................................................... 3-6

3-4 Power Management Setup .............................................. 3-8

3-5 PNP/PCI Configuration .................................................. 3-10

3-6 Integrated Peripherals ..................................................... 3-12

3-7 Load Setup Defaults........................................................ 3-14

3-8 Change Supervisor or User Password............................. 3-15

3-9 IDE HDD Auto Detection............................................... 3-16

3-10 HDD Low Level Format ................................................. 3-18

3-11 Save & Exit Setup ........................................................... 3-18

3-11 Exit Without Saving ........................................................ 3-18

Chapter 4 - Onboard Technical Information.................. 4-1

4-1 I/O & Memory Map......................................................... 4-1

4-2 Time & DMA Channels Map .......................................... 4-2

4-3 Interrupt Map ................................................................... 4-2

4-4 RTC & CMOS RAM Map ............................................... 4-3

Appendix A: Post Codes ........................................................ 4-4

Appendix B: Connectors ....................................................... 4-8

Appendix C: AGP Driver for Win95 Installation Guide.... 4-11

Introduction 1-1

Chapter 1

Introduction

This mainboard is a high performance system hardware based on Intel

Pentium processor and is equipped with an AGP slot, four PCI slots, three

standard ISA slots, Super Multi-I/O controller and dual port PCI-IDE

connectors for the future expansion. The hardware dimension is 305mm x

200mm with a four-layer-design technology.

Specification

VIA Apollo MVP3 AGP/PCIset chipset.

Intel Pentium Processor, Pentium Processor with MMX technology, AMD

K5/K6, Cyrix 6x86L/6x86MX & idt C6 operating at 133 ~ 500 MHz with 321

ZIF socket 7 provides scalability to accept faster Processors in the future.

Supports up to 384 MegaBytes of memory (168-Pin DIMM SOCKET x 3)

Supports1024KB(Optional) L2Cache.

Supports two 16 bit ISA slots ,five 32 bit PCI slots and an AGP slot and

provides two independent high performance PCI IDE interfaces capable of

supporting PIO Mode 3/4 and Ultra-DMA33 devices.

Supports ATAPI (e.g. CD-ROM) devices on both IDE interfaces.

Supports a floppy port, a parallel port (EPP,ECP port), two serial ports

(16550 Fast UART compatible), 2 USB Ports, a PS/2 style mouse connecter

and a PS/2 style keyboard connector.

Supports Award Plug & Play BIOS.

Supports CPU Hardware sleep, APM (Advanced Power Management) and

ACPI (Advanced Configuration Power Interface).

Supports an ATX power supply connector for a Remote On/Off , a Phone-

Ring Power On and a Keyboard Power On Function.

Supports Switching Regulator for CPU power supply. and single jumper for

CPU working voltage selection.

Supports ESDJ (Easy Setting Dual Jumper) function for CPU selection.

Support hardware monitor function.

Hardware Design 2-1

2-1MainboardLayout

This mainboardis designed with VIA Apollo MVP3 AGP/PCIset chipset which is

developed by VIA Corporation to fully support Pentium Processor PCI/ISA system.

By providing a massive increase in the bandwidth available between the video card

and the processor (66MHz), the unique feature of AGP supported by VIA Apollo

MVP3 chipset improves the speed of rendering and texturing for 3D graphics.The

chipset also provides an integrated IDE controller with two high performance IDE

interfaces for up to four IDE devices (hard devices, CD-ROM device, etc). The

Winbond W83877TF Super I/O controller provides the standard PC I/O function:

one floppy interface, two 16 Byte FIFO serial ports and one EPP/ECP capable parallel

port. This mainboard layout is shown in the next page for user's reference.Care must

be taken when inserting memory modules, CPUs or even plugging PCI card into

associated slots to avoid damaging any circuits or sockets on board. A cooling fan is

stronglyrecommendedwheninstallingPentium/PentiumMMX/K5/K6/6x86/6x86L/

6x86MX/C6 processor due to possible overheat.

Thismainboard supports a minimum of 8MB and a maximum of 384MB of System

Memory while Onboard 1024KB cache to increase system performance.

This mainboard supports standard Fast Page, EDO (Extended Data Out or Hyper

Page Mode) or synchronous DRAM. This mainboardprovides two 168-pin DIMM

sites for memory expansion. The sockets support 1M x 64(8MB), 2M x 64(16MB), 4M

x 64(32MB), and 8M x 64(64MB) single-sided or double-sided memory modules. The

memory timing requires 70 ns Fast page devices or 60 ns EDO DRAM. (DRAM

Modules may be parity [x 36] or non-parity [x 32].

Thismainboard supportstwoOnboard PCI IDEconnectors, and automatically

detects IDE harddisk type by BIOS utility automatic.

This mainboard supports Award Plug & Play BIOS for the ISA and PCI cards. The

BIOS can be located in Flash EPROM which can replace BIOS code easily if

necessary.

Chapter 2

Hardware design

2-2 EP-MVP3G-M

Figure2-1

EP-MVP3G-M Layout

PCI Slot #1

AGP SLOT

PCI Slot #2

PCI Slot #3

PCI Slot #4

ISA Slot #1

ISA Slot #2

Battery

ATX Power Input

Winbond

83877TF

I/Oset

COM 1

USB

COM 2

Parallel Port

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

PS/2

Keyboard

(Bottom)

Chassis FAN

DIMM 2

DIMM 3

DIMM 1

Bank 2

Bank 1

Bank 0

IDE2

Secondary IDE

IDE1

FDD1

Flash Memory

for BIOS

SB-Link

J7:WOL

CPU FAN

PWR FAN

RESET

SPK

KEYLOCK

POWER_ON

IR CONN.

PCI Slot #5

3.2V

2.9V

2.8V

2.4V

2.2V

2.1V

JP2

64K*6464K*64

JP4

SOCKET 7

JP1

Multiplier X Bus CLOCK

JP3

100MHz

95MHz

83MHz

75MHz

66MHz

2.5X

4.5X

3.5X

2 1

28 27

112MHz

JP5

5.5X

Hardware Design 2-3

2-2Connectors andJumpers

This section describes the connectors and jumpers equipped in the mainboard.

Please refer to Figure 2-1 for the location of each connector and jumper.

2-4 EP-MVP3G-M

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your

connections (figure 2-2).

J2: Keylock, Speaker, Reset

J3: IR Conn. TB-LED, HDD-LED, POWER_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J5: POWER Supply FAN POWER

• A plug-in for Power Supply Fan

J6: Chassis Fan Power

• A Plug-in for the chassis Fan Power

J7: WOL (Wake on Lan) Connector

J8: SB_Link Header

Figure 2-2

USB 1

(Top)

USB 0

PS/2 Mouse

(Top)

PS/2 Keyboard

Parallel Port

(Top)

Com1 Com2

1234567890123456789012345678901212345678901234567890123456789012123456789012345

Hardware Design 2-5

Power On/Off - This is connected to the power button on the

case. Using the Soft-Off by Pwr-BTTN feature, you can

choose either Instant Off (turns system off immediatly), or 4

sec delay (you need to hold the button down for 4 seconds

before the system turns off). When the system is in 4 sec

delay mode, this mainboard has added a special feature to

make the system go into suspend mode when the button is

pressed momentarily.

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is

selected

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

IDE LED indicator - LED ON when Onboard PCI IDE

Hard disks is activate

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. Keylock

2. N/C 5. GND

3. GND

Andere Handbücher für EP-MVP3G-M

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX GXA486SPM Bedienungsanleitung

EPOX

EPOX EP-5BTXA-E Bedienungsanleitung

EPOX

EPOX F62 Bedienungsanleitung

EPOX

EPOX LX370Y Bedienungsanleitung

EPOX

EPOX 3WXA Bedienungsanleitung

EPOX

EPOX EP-3VCA2 Bedienungsanleitung

EPOX

EPOX EP-4BDM Bedienungsanleitung

EPOX

EPOX EP-8KTA Bedienungsanleitung

EPOX

EPOX 8KTA Bedienungsanleitung

EPOX

EPOX EP-3VWM Bedienungsanleitung

EPOX

EPOX MVP3G-M Bedienungsanleitung

EPOX

EPOX EP-4PEA Bedienungsanleitung

EPOX

EPOX EP-BX6 Bedienungsanleitung

EPOX

EPOX EP-3C1A Bedienungsanleitung

EPOX

EPOX EP-3WXM2 Bedienungsanleitung

EPOX

EPOX MVP4M Bedienungsanleitung

EPOX

EPOX kl-133m Bedienungsanleitung

EPOX

EPOX M762A Series Bedienungsanleitung

EPOX

EPOX ProNiX EP-9NPAJ Bedienungsanleitung

EPOX

EPOX EP-LX370Y Bedienungsanleitung

EPOX

EPOX EP-58MVP3C-M Bedienungsanleitung

EPOX

EPOX S7-530A Bedienungsanleitung

EPOX

EPOX 3VCA Bedienungsanleitung

EPOX

EPOX 3XCA2 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung