Epson S1D13513 Bedienungsanleitung

Rev. 1.2

S1D13513 Display Controller

S5U13513P00C100 Evaluation

Board User Manual

Document Number: X78A-G-003-01.2

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission

of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does

not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application

or use in any product or circuit and, further, there is no representation that this material is applicable to products

requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights

is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance

with this material will be free from any patent or copyright infringement of a third party. When exporting the

products or technology described in this material, you should comply with the applicable export control laws and

regulations and follow the procedures required by such laws and regulations. You are requested not to use, to resell,

to export and/or to otherwise dispose of the products (and any technical information furnished, if any) for the devel-

opment and/or manufacture of weapon of mass destruction or for other military purposes.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective

companies.

Evaluation Board/Kit and Development Tool Important Notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop-

ment purposes only. Do not use it for other purposes. It is not intended to meet the requirements of design for finished

products.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product.

The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any

kind of damage and/or fire caused by the use of it. The user should cease to use it when any abnormal issue occurs even

during proper and safe use.

3. The part used for this evaluation board/kit or development tool may be changed without any notice.

2Seiko Epson Corporation S5U13513P00C100 Evaluation Board

Rev. 1.2

S5U13513P00C100 Evaluation Board Seiko Epson Corporation 3

Rev. 1.2

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1.2 Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1.3 S1D13513 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.4 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4.1 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . . . . 15

4.4.2 Connecting to the Epson PC Card Extender Board . . . . . . . . . . . . . . . . . . 15

4.4.3 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.5 LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.6 Camera Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.7 YUV Output for TV Display . . . . . . . . . . . . . . . . . . . . . . . . 19

4.8 Keypad Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.9 PWM Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.10 GPIO Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.11 JTAG Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7 S5U13513P00C100 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8 Change Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4Seiko Epson Corporation S5U13513P00C100 Evaluation Board

Rev. 1.2

Introduction

S5U13513P00C100 Evaluation Board Seiko Epson Corporation 5

Rev. 1.2

1 Introduction

This manual describes the setup and operation of the S5U13513P00C100 Evaluation

Board. The evaluation board is designed as an evaluation platform for the S1D13513

Display Controller.

The S5U13513P00C100 evaluation board can connect to the S5U13U00P00C100 USB

Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. With

some minor modifications, it is possible to connect the S5U13513P00C100 evaluation

board to a Epson PC Card Extender board instead of a USB Adapter board. The

S5U13513P00C100 evaluation board can also be used with many other native platforms via

the host connectors which provide the appropriate signals to support a variety of CPUs.

This document is updated as appropriate. Please check for the latest revision of this

document before beginning any development. The latest revision can be downloaded at

vdc.epson.com.

We appreciate your comments on our documentation. Please contact us via email at

vdc-document[email protected]pson.com.

Features

6Seiko Epson Corporation S5U13513P00C100 Evaluation Board

Rev. 1.2

2 Features

The S5U13513P00C100 Evaluation Board includes the following features:

• 256-pin PBGA S1D13513 Display Controller

• On-board SDRAM, selectable as 8MB x 32-bit or 8MB x 16-bit

• Headers for connection to the S5U13U00P00C100 USB Adapter board or to the PC

Card Extender board

• Headers for connecting to various Host Bus Interfaces

• Headers for connecting to LCD panels

• Headers for connecting to cameras

• On-board 10MHz crystal (used for OSC1 clock input)

• On-board 27MHz crystal (used for OSC2 clock input)

• 14-pin DIP socket (used to install an oscillator for CLKI3 clock input)

• 3.3V input power

• On-board voltage regulator with 1.8V output

Installation and Configuration

S5U13513P00C100 Evaluation Board Seiko Epson Corporation 7

Rev. 1.2

3 Installation and Configuration

The S5U13513P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm

resistors which allow it to be used with a variety of different configurations.

3.1 Configuration DIP Switch

The S1D13513 has configuration inputs (CNF[8:0]) which are read on the rising edge of

RESET#. A 10-position DIP switch (SW1) is used to configure the S1D13513 for multiple

Host Bus Interfaces. The following figure shows the location of DIP switch SW1 on the

S5U13513P00C100.

Figure 3-1: Configuration DIP Switch (SW1) Location

All S1D13513 configuration inputs (CNF[8:0]) are fully configurable using DIP switch

SW1 as described below.

Table 3-1: Summary of Power-On/Reset Options

SDU13513B00C

SW1-[10:1] Config

S1D13513

CNF[8:0] Config

Power-On/Reset State

1 (ON) 0 (OFF)

SW1-[10] - Not used

SW1-[9:8] CNF[8:7]

00b CLKI3 is the PLL1 clock source

01b BUSCLK is the PLL1 clock source

10b OSC1 is the PLL1 clock source

11b OSC2 is the PLL1 clock source

SW1-[6] CNF5 Indirect access Direct access

SW1-[7] CNF6 See Table 3-2: “CNF[4:0] Setting

for CNF[6] = 1b”

See Table 3-3: “CNF[4:0] Setting for

CNF[6] = 0b”

SW1-[5:1] CNF[4:0] 00000b Parallel Direct 80 Type 2: 1CS#

(see Table 3-2: “CNF[4:0] Setting for CNF[6] = 1b” )

= Required settings when using S5U13U00P00C100 USB Adapter board (SW1-[9:1] = 101000000b)

DIP SWITCH - SW1

Installation and Configuration

8Seiko Epson Corporation S5U13513P00C100 Evaluation Board

Rev. 1.2

Table 3-2: CNF[4:0] Setting for CNF[6] = 1b

CNF[4:0] Host Bus

00000b Parallel Direct 80 Type 2: 1 CS#

00001b Reserved

00010b Parallel Indirect 80 Type 2

00011b Reserved

00100b Parallel Direct 80 Type 1: 1 CS#

00101b Parallel Direct 68: 1 CS#

00110b Parallel Indirect 80 Type 1

00111b Parallel Indirect 68

01000b Parallel Direct 80 Type 2: 2 CS#

01001b Reserved

01010b Reserved

01011b Reserved

01100b Parallel Direct 80 Type 1: 2 CS#

01101b Parallel Direct 68: 2 CS#

01110b Reserved

01111b Reserved

10000b Serial on HVDD1: Data valid on falling edge

10001b Serial on HVDD2: Data valid on falling edge

10010b Reserved

10011b Reserved

10100b Reserved

10101b Reserved

10110b Reserved

10111b Reserved

11000b Serial on HVDD1: Data valid on rising edge

11001b Serial on HVDD2: Data valid on rising edge

11010b Reserved

11011b Reserved

11100b Reserved

11101b Reserved

11110b Reserved

11111b Reserved

= Required settings when using S5U13U00P00C100 USB Adapter board

(SW1-[9:1] = 101000000b)

Installation and Configuration

S5U13513P00C100 Evaluation Board Seiko Epson Corporation 9

Rev. 1.2

Table 3-3: CNF[4:0] Setting for CNF[6] = 0b

CNF[4:0] Host Bus

00000b Generic Little Endian: Active Low WAIT# with tri-state

00001b Generic Little Endian: Active Low WAIT# always driven

00010b Generic Little Endian: Active HIgh WAIT# with tri-state

00011b Reserved

00100b Generic Big Endian: Active Low WAIT# with tri-state

00101b Generic Big Endian: Active Low WAIT# always driven

00110b Generic Big Endian: Active HIgh WAIT# with tri-state

00111b Reserved

01000b MIPS/ISA Little Endian: Active Low WAIT# with tri-state

01001b MIPS/ISA Little Endian: Active Low WAIT# always driven

01010b MIPS/ISA Little Endian: Active HIgh WAIT# with tri-state

01011b Reserved

01100b MC68000 Big Endian: Active High WAIT# with tri-state

01101b Reserved

01110b MC68030 Big Endian: Active High WAIT# with tri-state

01111b Reserved

10000b PR31500/31700/TX3912 Little Endian: Active Low WAIT# with tri-state

(16-bit memory accesses only)

10001b PR31500/31700/TX3912 Little Endian: Active Low WAIT# always driven

(16-bit memory accesses only)

10010b Reserved

10011b Reserved

10100b Reserved

10101b Reserved

10110b MPC821/555/556 Big Endian: Active High WAIT# with tri-state

10111b Reserved

11000b SH3 Little Endian: Active Low WAIT# with tri-state

11001b SH3 Little Endian: Active Low WAIT# always driven

11010b SH4 Little Endian: Active High WAIT# with tri-state

11011b Reserved

11100b SH3 Big Endian: Active Low WAIT# with tri-state

11101b SH3 Big Endian: Active Low WAIT# always driven

11110b SH4 Big Endian: Active High WAIT# with tri-state

11111b Reserved

Installation and Configuration

10 Seiko Epson Corporation S5U13513P00C100 Evaluation Board

Rev. 1.2

3.2 Configuration Jumpers

The S5U13513P00C100 has 11 jumper blocks which configure various board settings. The

jumper positions for each function are shown below.

Table 3-4: Configuration Jumper Summary

Jumper Function Position 1-2 Position 2-3 No Jumper

JP1 COREVDD Normal — COREVDD current

measurement

JP2 PLLVDD1 Normal — PLLVDD1 current

measurement

JP3 PLLVDD2 Normal — PLLVDD2 current

measurement

JP4 OSCVDD1 Normal — OSCVDD1 current

measurement

JP5 OSCVDD2 Normal — OSCVDD2 current

measurement

JP6 HVDD1 Normal — HVDD1 current

measurement

JP7 HVDD2 Normal — HVDD2 current

measurement

JP8 HVDD3 Normal — HVDD3 current

measurement

JP9 HVDD4 Normal — HVDD4 current

measurement

JP10 HVDD5 Normal — HVDD5 current

measurement

JP11 SDRAM Width Select 32-bit wide SDRAM 16-bit wide SDRAM —

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epson Hauptplatine Handbücher

Epson

Epson S5U13L01P00C100 Bedienungsanleitung

Epson

Epson S5U13706B00C Bedienungsanleitung

Epson

Epson S5U13705B00C Bedienungsanleitung

Epson

Epson S1R72V18 Bedienungsanleitung

Epson

Epson S1D13709 Bedienungsanleitung

Epson

Epson S5U13A04B00C Bedienungsanleitung

Epson

Epson S1C31D50 Bedienungsanleitung

Epson

Epson S5U13U11 Bedienungsanleitung

Epson

Epson S5U1C31D50T1 Bedienungsanleitung

Epson

Epson S1S65010 Bedienungsanleitung

Epson

Epson S5U1C17965T2 Bedienungsanleitung

Epson

Epson S5U12517P00C100 Bedienungsanleitung

Epson

Epson S5U1C6S3N2E2 Bedienungsanleitung

Epson

Epson S5U1C17F57T Bedienungsanleitung

Epson

Epson S5U13513P00C100 Bedienungsanleitung

Epson

Epson S1V30000 Series Benutzerhandbuch

Epson

Epson S5U13781R00C100 Bedienungsanleitung

Epson

Epson S1D13743 Bedienungsanleitung

Epson

Epson S5U13506P00C100 Bedienungsanleitung

Epson

Epson S5U13515P00C100 Bedienungsanleitung

Epson

Epson S5U13U00P00C100 Bedienungsanleitung

Epson

Epson S5U13517P00C100 Bedienungsanleitung

Epson

Epson S5U13706P00C100 Bedienungsanleitung

Epson

Epson SG-WRITERII Gebrauchsanweisung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung